Read Sony HT-DDW5000 / HT-DDW7000 / SA-WP5000 / SS-CNP5000 / SS-CRP5000 / SS-CRP7001 / SS-MSP5000 / SS-SRP5000 Service Manual online
SERVICE MANUAL
Sony Corporation
Audio Business Group
Published by Sony Techno Create Corporation
SPECIFICATIONS
SA-WP5000
ACTIVE SUBWOOFER
SS-CNP5000/MSP5000/SRP5000
SPEAKER SYSTEM
9-889-038-02
2008E05-1
©
2008.05
E Model
Australian Model
• SA-WP5000 is the active subwoofer in HT-DDW5000/DDW7000.
• SS-CNP5000 is the center speaker in HT-DDW5000/DDW7000.
• SS-MSP5000 is the front speaker in HT-DDW5000/DDW7000.
• SS-SRP5000 is the surround/surround back speaker in HT-DDW5000/
• SS-CNP5000 is the center speaker in HT-DDW5000/DDW7000.
• SS-MSP5000 is the front speaker in HT-DDW5000/DDW7000.
• SS-SRP5000 is the surround/surround back speaker in HT-DDW5000/
DDW7000.
• SS-CRP5000/CRP7001 are composed of SS-CNP5000, SS-MSP5000
and SS-SRP5000.
SA-WP5000/SS-CNP5000/CRP5000/
CRP7001/MSP5000/SRP5000
Photo: SA-WP5000
Photo: SS-CNP5000
Photo: SS-MSP5000
Photo: SS-SRP5000
SS-CRP5000/CRP7001 COMPONENT MODEL NAME
SS-CRP5000/CRP7001
Front speaker
SS-MSP5000
Center speaker
SS-CNP5000
Surround/Surround back speaker
SS-SRP5000
Speaker section
• Front speaker (SS-MSP5000)
Speaker system
2-way, 3-driver, Bass
reflex, Magnetically
shielded
reflex, Magnetically
shielded
Speaker unit
Woofer:
Woofer:
160 mm, cone type × 2
Tweeter:
25 mm, horn type
Rated Impedance
4 ohm
Dimensions (width/height/depth) (Approx.)
305 × 1,000 × 325 mm
(with foot)
Mass (Approx.)
13.5 kg
• Center speaker (SS-CNP5000)
Speaker system
2-way, 3-driver, Bass
reflex, Magnetically
shielded
reflex, Magnetically
shielded
Speaker unit
Woofer:
Woofer:
100 mm, cone type × 2
Tweeter:
25 mm, horn type
Rated Impedance
4 ohm
Dimensions (width/height/depth) (Approx.)
515 × 175 × 225 mm
(with foot)
Mass (Approx.)
4.8 kg
• Surround/Surround back speaker
(SS-SRP5000)
Speaker system
Full range, Bass reflex
Speaker unit
Woofer:
Woofer:
100 mm, cone type
Rated Impedance
4 ohm
Dimensions (width/height/depth) (Approx.)
174 × 220 × 166 mm
(with foot)
Mass (Approx.)
1.4 kg
• Subwoofer (SA-WP5000)
Speaker system
Active subwoofer, Bass
reflex, Magnetically
shielded
reflex, Magnetically
shielded
Speaker unit
250 mm, cone type
RMS output
200 W
5)
175 W
6)
Input
LINE IN (input pin jacks)
5)
Measured under the following conditions:
6)
Measured under the following conditions:
Area code
Power requirements
E51, SP, MY, AUS
240 V AC, 50 Hz
MX
127 V AC, 60 Hz
AR, TH
230 V AC, 50 Hz
Area code
Power requirements
AR, TH
220 V AC, 50 Hz
Power requirements
Power consumption 80 W
Dimensions (width/height/depth) (Approx.)
Dimensions (width/height/depth) (Approx.)
335 × 420 × 430 mm
(with foot)
Mass (Approx.)
11 kg
Design and specifications are subject to
change without notice.
change without notice.
Area code
Power requirements
SP, MY
230 – 240 V AC, 50/60 Hz
MX
127 V AC, 60 Hz
E51
120/220/240 V AC,
50/60 Hz
AUS
240 V AC, 50 Hz
AR, TH
220 – 230 V AC, 50/60 Hz
Ver. 1.1 2008.05
• Abbreviation
AR :
AR :
Argentina
model
AUS :
Australian
model
E51
: Chilean and Peruvian models
MX
: Mexican model
MY
: Malaysia model
SP
: Singapore model
TH :
Thai
model
SA-WP5000/SS-CNP5000/CRP5000/CRP7001/MSP5000/SRP5000
2
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40 °C higher
• Unleaded solder melts at a temperature about 40 °C higher
than ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350 °C.
Caution: The printed pattern (copper foil) may peel away if the
about 350 °C.
Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!
• Strong
viscosity
Unleaded solder is more viscous (sticky, less prone to fl ow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
•
Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
also be added to ordinary solder.
Notes on chip component replacement
•
•
Never reuse a disconnected chip component.
•
Notice that the minus side of a tantalum capacitor may be dam-
aged by heat.
aged by heat.
SAFETY-RELATED COMPONET WARNING!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE
WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS
WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS
WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS
MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
• JIG
When disassembling the set, use the following jig (for speaker
When disassembling the set, use the following jig (for speaker
removal).
Part No.: J-2501-238-A
JIG FOR SPEAKER REMOVAL
JIG FOR SPEAKER REMOVAL
SA-WP5000/SS-CNP5000/CRP5000/CRP7001/MSP5000/SRP5000
3
SECTION 1
DISASSEMBLY
Note: Follow the disassembly procedure in the numerical order given.
1-1. FRONT PANEL ASSY (SA-WP5000)
1-2. FRONT PANEL ASSY (SS-CNP5000)
Insert the jig (J-2501-238-A) into a space
and raise the front panel assy gradually.
Note:
When using a jig, please work so as not
to injure front panel and speaker cabinet.
Insert the jig (J-2501-238-A) into a space
and raise the front panel assy gradually.
Note:
When using a jig, please work so as not
to injure front panel and speaker cabinet.
eight bosses
front panel assy
Insert a flat-tip screwdriver into a recess
in the bottom of the set
to raise the front panel assy a little.
Insert the jig (J-2501-238-A) into a space
and raise the front panel assy gradually.
Note 1:
When using a jig, please work so as not
to injure front panel and speaker cabinet.
Note 2:
Please insert jig from a gap on the front
panel assy underside and expand the
surrounding gap in turn.
nine bosses
front panel assy
Insert a flat-tip screwdriver
into a recess in the bottom of the set
to raise the front panel assy a little.
SA-WP5000/SS-CNP5000/CRP5000/CRP7001/MSP5000/SRP5000
4
Insert the jig (J-2501-238-A) into a space
and raise the front panel assy gradually.
Note: When using a jig, please work so as not to injure
front panel and speaker cabinet.
Insert the jig (J-2501-238-A) into a space
and raise the duct panel assy gradually.
Note: When using a jig, please work
so as not to injure duct panel assy
and
speaker
cabinet.
Insert the jig (J-2501-238-A) into a space
and raise the duct panel assy gradually.
Note: When using a jig, please work
so as not to injure duct panel assy
and
speaker
cabinet.
ten bosses
twelve bosses
front panel assy
duct panel assy
1-3. FRONT PANEL ASSY, DUCT PANEL ASSY (SS-MPS5000)
