Read Sony HT-DDW1000 / STR-K1000P Service Manual online
2
STR-K1000P
Notes on chip component replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be
damaged by heat.
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40 °C higher
than ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350
°C.
Caution: The printed pattern (copper foil) may peel away if
the heated tip is applied for too long, so be careful!
• Strong viscosity
Unleaded solder is more viscou-s (sticky, less prone to flow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
also be added to ordinary solder.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK
0
OR DOTTED LINE
WITH MARK
0
ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE
PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR
IN SUPPLEMENTS PUBLISHED BY SONY.
REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE
PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR
IN SUPPLEMENTS PUBLISHED BY SONY.
• Abbreviation
AUS
AUS
: Australian model
E51
: Chilean and Peruvian models
MX
: Mexican model
SP
: Singapore model
SP6
: Singapore and Malaysia models
Video section
Inputs/Outputs
Video:
Video:
1 Vp-p, 75 ohms
COMPONENT VIDEO:
Y: 1 Vp-p, 75 ohms
P
P
B
/C
B
/B-Y: 0.7 Vp-p,
75 ohms
P
P
R
/C
R
/R-Y: 0.7 Vp-p,
75 ohms
80 MHz HD Pass Through
80 MHz HD Pass Through
General
Power requirements
Power consumption
200 W
Power consumption (during standby mode)
0.2 W
Dimensions (w/h/d) (Approx.)
430 1 58 310 mm
(16 7/8
(16 7/8
× 6 2/8 × 12 2/8
inches) including
projecting parts and
controls
projecting parts and
controls
Mass (Approx.)
8.0 kg (17 lb 11 oz)
Area code
Power requirements
SP, SP6
220–230 V AC, 50/60 Hz
AUS
240 V AC, 50 Hz
MX
127 V AC, 60 Hz
E51
120/220/240 V AC,
50/60 Hz
50/60 Hz
Design and specifications are subject to change
without notice
without notice
Ver. 1.1
Click on the first or last page to see other HT-DDW1000 / STR-K1000P service manuals if exist.