Read Sony HT-CT550W / STR-CT550WT Service Manual online
STR-CT550WT
3
SECTION 1
SERVICING NOTES
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40 °C higher
• Unleaded solder melts at a temperature about 40 °C higher
than ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350 °C.
Caution: The printed pattern (copper foil) may peel away if
about 350 °C.
Caution: The printed pattern (copper foil) may peel away if
the heated tip is applied for too long, so be careful!
• Strong
viscosity
Unleaded solder is more viscous (sticky, less prone to fl ow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
also be added to ordinary solder.
NOTE THE IC3500 AND IC3501 ON THE HDMI BOARD
REPLACING
IC3500 and IC3501 on the HDMI board cannot exchange with sin-
gle. When these parts are damaged, exchange the entire mounted
board.
REPLACING
IC3500 and IC3501 on the HDMI board cannot exchange with sin-
gle. When these parts are damaged, exchange the entire mounted
board.
CAPACITOR ELECTRICAL DISCHARGE PROCESSING
When checking the board, for the electric shock prevention, con-
nect the resistors to both ends of respective capacitor (C935 or
936) to discharge the capacitor (C935 or 936).
When checking the board, for the electric shock prevention, con-
nect the resistors to both ends of respective capacitor (C935 or
936) to discharge the capacitor (C935 or 936).
– POWER Board (Conductor Side) –
800
:/2 W
C935 (US, Canadian and Taiwan models)
C936 (AEP and UK models)
ADVANCE PREPARATION WHEN CONFIRMING OP-
ERATION
All of the units included in the HT-CT550W (SA-WCT550W/SS-
CT550W/STR-CT550WT (main unit)/EZW-RT50) are required to
confi rming operation of the main unit. Check in advance that you
have all of the units.
ERATION
All of the units included in the HT-CT550W (SA-WCT550W/SS-
CT550W/STR-CT550WT (main unit)/EZW-RT50) are required to
confi rming operation of the main unit. Check in advance that you
have all of the units.
COMPLETING SETTINGS FOR THE WIRELESS
SOUND SYSTEM
Procedure:
1. Insert the two supplied wireless transceivers (EZW-RT50) into
SOUND SYSTEM
Procedure:
1. Insert the two supplied wireless transceivers (EZW-RT50) into
the wireless transceiver slot on the rear panel of both the re-
ceiver (STR-CT550WT) and the subwoofer (SA-WCT550W).
ceiver (STR-CT550WT) and the subwoofer (SA-WCT550W).
Rear panel of the receiver (STR-CT550WT)
Wireless transceiver
(EZW-RT50)
(EZW-RT50)
Rear panel of the subwoofer (SA-WCT550W)
Wireless transceiver
(EZW-RT50)
(EZW-RT50)
2. Press the [
?/1
] (Power) button on the receiver (STR-CT550
WT: main unit).
3. If wireless transmission is activated, the LINK/STANDBY in-
dicator on the subwoofer (SA-WCT550W) turns green.
Note: Refer to the instruction manual for assistance if the LINK/STAND-
BY indicator on the subwoofer (SA-WCT550W) does not turn on.
MODEL IDENTIFICATION
– Model Number Label –
Power
Voltage
Indication
Voltage
Indication
Model
Power Voltage Indication
US and Canadian models
- 120V 60Hz 50W
AEP and UK models
- 220-240V 50/60Hz 50W
Taiwan model
- 120V 50/60Hz 50W
NOTE OF REPLACING THE IC3100 ON THE MAIN
BOARD AND THE COMPLETE MAIN BOARD
When IC3100 on the MAIN board and the complete MAIN board
are replaced, it is necessary to spread the compound (THERMAL
COMPOUND G747) (Part No. J-2501-221-A) between the main
board and the heat sink.
Spread the compound referring to the fi gure below.
BOARD AND THE COMPLETE MAIN BOARD
When IC3100 on the MAIN board and the complete MAIN board
are replaced, it is necessary to spread the compound (THERMAL
COMPOUND G747) (Part No. J-2501-221-A) between the main
board and the heat sink.
Spread the compound referring to the fi gure below.
– MAIN Board (Component Side) –
thermal compound G747
IC3100
Ver. 1.1
Click on the first or last page to see other HT-CT550W / STR-CT550WT service manuals if exist.