Read Sony HT-CT150 / HT-CT350 / SA-WCT150 / SA-WCT350 Service Manual online
SA-WCT150/WCT350
4
SECTION 1
SERVICING NOTES
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40 °C higher
• Unleaded solder melts at a temperature about 40 °C higher
than ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350 °C.
Caution: The printed pattern (copper foil) may peel away if
about 350 °C.
Caution: The printed pattern (copper foil) may peel away if
the heated tip is applied for too long, so be careful!
•
Strong viscosity
Unleaded solder is more viscous (sticky, less prone to fl ow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
•
Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
also be added to ordinary solder.
MODEL IDENTIFICATION
Bar cord
Model Number Label
– Rear View –
Part No.
Model
Part No.
WCT150: US and Canadian models
4-166-506-0
[]
WCT350: US and Canadian models
4-174-743-0
[]
WCT350: AEP model
4-174-931-0
[]
WCT350: UK model
4-174-933-0
[]
WCT350: Russian model
4-174-934-0
[]
WCT150: Saudi Arabia model
4-177-835-0
[]
WCT150: Chilean and Peruvian
models
4-184-061-0
[]
WCT150: Singapore model
4-184-062-0
[]
WCT350: Singapore model
4-184-063-0
[]
WCT350: Taiwan model
4-184-064-0
[]
WCT350: Thai model
4-184-065-0
[]
ADVANCE PREPARATION WHEN CONFIRMING OP-
ERATION
When the operation of the subwoofer (SA-WCT150/WCT350) is
confi rmed, it is necessary to connect subwoofer (SA-WCT150/
WCT350) and satellite speaker (SS-CT150/CT350).
Confi rm the subwoofer (SA-WCT150/WCT350) and satellite
speaker (SS-CT150/CT350) are prepared beforehand when you
repair.
ERATION
When the operation of the subwoofer (SA-WCT150/WCT350) is
confi rmed, it is necessary to connect subwoofer (SA-WCT150/
WCT350) and satellite speaker (SS-CT150/CT350).
Confi rm the subwoofer (SA-WCT150/WCT350) and satellite
speaker (SS-CT150/CT350) are prepared beforehand when you
repair.
NOTE THE IC3500 AND IC3501 ON THE HDMI BOARD
REPLACING
IC3500 and IC3501 on the HDMI board cannot exchange with sin-
gle. When these parts are damaged, exchange the entire mounted
board.
REPLACING
IC3500 and IC3501 on the HDMI board cannot exchange with sin-
gle. When these parts are damaged, exchange the entire mounted
board.
NOTE OF REPLACING THE IC340 AND IC400 ON THE
MAIN BOARD AND THE COMPLETE MAIN BOARD
When IC340 and IC400 on the MAIN board and the complete
MAIN board are replaced, it is necessary to spread the compound
(THERMAL COMPOUND G747) (Part No. J-2501-221-A) be-
tween the main board and the heat sink.
Spread the compound referring to the fi gure below.
MAIN BOARD AND THE COMPLETE MAIN BOARD
When IC340 and IC400 on the MAIN board and the complete
MAIN board are replaced, it is necessary to spread the compound
(THERMAL COMPOUND G747) (Part No. J-2501-221-A) be-
tween the main board and the heat sink.
Spread the compound referring to the fi gure below.
– MAIN Board (Component Side) –
thermal compound G747
(J-2501-221-A)
(J-2501-221-A)
IC400
IC340
CAPACITOR ELECTRICAL DISCHARGE PROCESSING
When checking the board, for the electric shock prevention, con-
nect the resistors to both ends of respective capacitor (C903) to
discharge the capacitor (C903).
When checking the board, for the electric shock prevention, con-
nect the resistors to both ends of respective capacitor (C903) to
discharge the capacitor (C903).
800
:/2 W
C903
– POWER Board (Conductor Side) –
• JIG
When disassembling the set, use the following jig (for speaker
When disassembling the set, use the following jig (for speaker
removal).
Part No. J-2501-238-A JIG FOR SPEAKER REMOVAL
Ver. 1.3
Click on the first or last page to see other HT-CT150 / HT-CT350 / SA-WCT150 / SA-WCT350 service manuals if exist.