Read Sony HST-471 / SEN-471 Service Manual online
— 5 —
2.
Turn the adjustment screw and check output peaks. If the peaks
do not match for L-CH and R-CH, turn the adjustment screw
so that outputs match within 1dB of peak.
do not match for L-CH and R-CH, turn the adjustment screw
so that outputs match within 1dB of peak.
3.
Mode: Playback (FWD)
4.
Repeat steps 1 to 3 in playback (REV) mode.
5.
After the adjustments, apply suitable locking compound to the
pats adjusted.
pats adjusted.
Adjustment Location:
Record/Playback Head (Deck A and B)
and main board.
and main board.
reverse
forward
Tape Speed Adjustment
DECK A
Note: Start the Tape Speed adjustment as below after setting to the
test mode.
Procedure:
Mode: Playback (FWD)
Mode: Playback (FWD)
1.
Insert the WS-48B into the deck A and the blank tape into the
deck B.
deck B.
2.
Press the REC button and
· button on the deck B. Then
the deck B is at recording mode.
3.
Set the deck A to playback mode.
4.
Press the DUBBING SPEED HIGH button in playback mode.
Then at HIGH speed mode.
Then at HIGH speed mode.
5.
Adjust RV652 on the AUDIO board do that frequency counter
reads 6,000 ± 90 Hz.
reads 6,000 ± 90 Hz.
6.
Press the DUBBING SPEED NORMAL button in playback
mode.
Then at NORMAL speed mode.
mode.
Then at NORMAL speed mode.
7.
Adjust RV651 on the AUDIO board so that frequency counter
reads 3,000 ± 90Hz.
reads 3,000 ± 90Hz.
8.
Frequency difference between deck A and deck B the beginning
of the tape should be within ± 1.5 %.
of the tape should be within ± 1.5 %.
Adjustment Location: AUDIO board
Sample Value of Wow and flutter
W.RMS (JIS) within 0.3%
(test tape: WS-48B)
(test tape: WS-48B)
Playback level Adjustment
DECK A
DECK B
Procedure:
Mode: Playback (FWD)
Mode: Playback (FWD)
Deck A is RV311 (L-CH) and RV411 (R-CH), Deck B is RV301
(L-CH) and RV401 (R-CH) so that adjustment within adjustment
level as follows.
Adjustment Level:
(L-CH) and RV401 (R-CH) so that adjustment within adjustment
level as follows.
Adjustment Level:
VIDEO1 AUDIO OUT PB level: 301.5 to 338.3 mV (–8.2 to
–7.2 dB) level difference between the channels: within ± 0.5
dB
–7.2 dB) level difference between the channels: within ± 0.5
dB
Adjustment Location: AUDIO and main boards
Screw
position
position
L-CH
peak
peak
within
1dB
1dB
output
level
level
L-CH
peak
peak
R-CH
peak
peak
within
1dB
1dB
Screw
position
position
R-CH
peak
peak
set
test tape
P-4-A100
(10kHz, –10dB)
P-4-A100
(10kHz, –10dB)
oscilloscope
L
R
V
waveform of oscilloscope
in phase 45
°
90
°
135
°
180
°
good
wrong
rear panel
VIDEO1
AUDIO OUT connector
AUDIO OUT connector
H
+
–
–
set
test tape
WS-48B
(3 kHz, 0 dB)
WS-48B
(3 kHz, 0 dB)
frequency counter
rear panel
VIDEO1
AUDIO OUT connector
(L: L-CH)
(R: R-CH)
AUDIO OUT connector
(L: L-CH)
(R: R-CH)
+
–
–
level meter
set
test tape
P-4-L300
(315 Hz, 0 dB)
P-4-L300
(315 Hz, 0 dB)
rear panel
VIDEO1
AUDIO OUT connector
(L: L-CH)
(R: R-CH)
AUDIO OUT connector
(L: L-CH)
(R: R-CH)
Click on the first or last page to see other HST-471 / SEN-471 service manuals if exist.