Read Sony HS-WV1 Service Manual online
SERVICE MANUAL
Published by Sony Techno Create Corporation
Sony Corporation
Audio&Video Business Group
HS-WV1
SPECIFICATIONS
AV WALL PORT
9-889-380-01
2009A04-1
©
2009.01
US Model
Ver. 1.0 2009.01
Input and output terminals
RJ45: T568B Terminated. CD (only for connection to HS-KP1
RJ45: T568B Terminated. CD (only for connection to HS-KP1
(Keypad) or HS-MB1 (Distribution Panel))
(C DC 19.5 V included)
E (only for connection to CAV-CVB1
(Component Video Balun) or HS-MB1
(Distribution Panel)) (DC10V included)
Pin jack:
COMPONENT VIDEO IN: 75 ohms terminal
COMPONENT VIDEO OUT: 75 ohms
impedance
AUDIO IN: 50 kilohms terminal
AUDIO OUT: 1 kilohm impedance
RS-232C:
For a Sony Multi Channel AV Receiver or
Service
IR REMOTE OUT:
Only for connecting an IR fl asher to operate a
Sony component.
DC IN 19.5 V:
HS-AC1 only, JEITA TYPE5 jacks
General
Power consumption (when HS-KP1, HS-MB1, and CAV-CVB1 are not
connected):
Power consumption (when HS-KP1, HS-MB1, and CAV-CVB1 are not
connected):
DC 19.5 V, 0.15 A
Operating temperature:
0 °C - 30 °C (32 °F - 86 °F)
Storage temperature:
– 20 °C - 60 °C (– 4 °F - 140 °F)
Dimensions (wall port):
74 × 110 × 66 mm
(3 × 4
3
/
8
× 2
5
/
8
inches) (w/h/d)
Dimensions (cover panel): 115 × 124 × 5.5 mm
(4
5
/
8
× 5 ×
1
/
4
inches) (w/h/d)
Mass:
200 g (7.1 oz) (cover panel included)
Design and specifi cations are subject to change without notice.
Unpacking
• HS-WV1 (1)
• Cover panel (1)
• Screws for 2 gang J-box (long) (4)
• Screws for cover panel (short) (4)
• Installer’s manual (this manual) (1)
• HS-WV1 (1)
• Cover panel (1)
• Screws for 2 gang J-box (long) (4)
• Screws for cover panel (short) (4)
• Installer’s manual (this manual) (1)
The other units referred to in this manual are optional. Prepare necessary
units depending on your system.
units depending on your system.
Connecting the CAT5 cables to the wall port
When the wall is finished, connect the CAT5 cables to the rear of the wall port.
1
Attach RJ45 connectors to the ends of the CAT5 cables.
For details, see “Connecting RJ45 connectors to CAT5 cables”.
2
Connect the units using the CAT5 cables as shown below:
To connect the wall port to Distribution Panel (HS-MB1)
%
$
&
SOURCE 4
SOURCE 1
% / #
$ / "
&
TO DISTRIBUTION PANEL HS-MB1
$ & %
OR TO KEYPAD HS-KP1
" & #
(WHEN USED WITHOUT HS-MB1)
TO DISTRIBUTION PANEL HS-MB1 OR
TO COMPONENT VIDEO BALUN CAV-CVB1
TO COMPONENT VIDEO BALUN CAV-CVB1
Distribution Panel
Rear of the wall port
To connect the wall port to Keypad (HS-KP1)
ZONE
MODE
DC IN
+
19.5V
GND
R
+
R-
L-
L
L-
L
+
SPEAKERS
IMPEDANCE USE
8 - 16
HT
IR REMOTE
IN
% / #
$ / "
&
TO DISTRIBUTION PANEL HS-MB1
$ & %
OR TO KEYPAD HS-KP1
" & #
(WHEN USED WITHOUT HS-MB1)
TO DISTRIBUTION PANEL HS-MB1 OR
TO COMPONENT VIDEO BALUN CAV-CVB1
TO COMPONENT VIDEO BALUN CAV-CVB1
Rear of Keypad
Rear of the wall port
Tip
The signal input from the COMPONENT VIDEO IN jacks can be output from the
& terminal.
To connect to a TV, use a Component Video Balun (CAV-CVB1).
HS-WV1
2
PARTS LIST
4-108-085-01 PLATE (L), ORNAMENTAL (COVER PANEL)
4-113-750-11
MANUAL, INSTALLATION (ENGLISH)
4-123-926-01 SCREW (WALL PLATE) (for COVER PANEL)
4-874-614-82 +BV TAPPING SCREW TYPE-1 3.5
(for 2 GANG J-BOX)
A-1557-938-A OVERALL
ASSY
(HS-WV1)
Ref. No.
Part No.
Description
Remark
HS-WV1
3
MEMO
HS-WV1
REVISION HISTORY
Checking the version allows you to jump to the revised page.
Also, clicking the version at the top of the revised page allows you to jump to the next revised page.
Also, clicking the version at the top of the revised page allows you to jump to the next revised page.
Ver.
Date
Description of Revision
1.0
2009.01
New