Read Sony HCD-ZX70DVD Service Manual online
20
Checking S Video Output S-C
<Purpose>
This checks whether the S-C satisfies the NTSC Standard. If it is
not correct, the colors will be too dark or light.
This checks whether the S-C satisfies the NTSC Standard. If it is
not correct, the colors will be too dark or light.
Mode
Video level adjustment in test mode
Signal
Color bars
Test point
CN005 pin 5
Instrument
Oscilloscope
Specification
286 ± 50 mVp-p
Connection:
Procedure:
1. Select the initial menu “6. Video Level Adjustment” in the test
1. Select the initial menu “6. Video Level Adjustment” in the test
mode so that color bars are generated. (Refer to “4-9. VIDEO
LEVEL ADJUSTMENT” on page 16)
LEVEL ADJUSTMENT” on page 16)
2. Confirm that the S-C burst is 286 ± 50 mVp-p.
Figure 5-3
4
5
100
µ
F
75
Ω
±
1%
100 k
±
1%
CN005
+
Oscilloscope
Adjustment Location :
– MB BOARD (Side A) –
286 ± 50 mVp-p
1
RV401
VIDEO LEVEL
5
2
4
4
CN005
VIDEO SECTION
Note:
During diagnostic check, the characters and color bars can be seen
only with the NTSC monitor. Therefore, for diagnostic check, use
the monitor that supports both NTSC and PAL modes
only with the NTSC monitor. Therefore, for diagnostic check, use
the monitor that supports both NTSC and PAL modes
Instruments required:
1) Color monitor TV
2) Oscilloscope 1 or 2 phenomena, band width over 100 MHz,
2) Oscilloscope 1 or 2 phenomena, band width over 100 MHz,
with delay mode
3) Frequency counter (over 8 digits)
4) Digital voltmeter
5) Remote commander
4) Digital voltmeter
5) Remote commander
RM-SD170 (1-418-911-11)
6) DVD reference disc
HLX-501 (J-6090-071-A) (dual layer)
HLX-503 (J-6090-069-A) (single layer)
HLX-504 (J-6090-088-A) (single layer)
HLX-505 (J-6090-089-A) (dual layer)
HLX-503 (J-6090-069-A) (single layer)
HLX-504 (J-6090-088-A) (single layer)
HLX-505 (J-6090-089-A) (dual layer)
7) SACD reference disc
HLXA-509 (J-6090-090-A)
Video Level Adjustment
<Purpose>
This adjustment is made to satisfy the NTSC standard, and if not
adjusted correctly, the brightness will be too large or small.
This adjustment is made to satisfy the NTSC standard, and if not
adjusted correctly, the brightness will be too large or small.
Mode
Video level adjustment in test mode
Signal
Color bars
Test point
VIDEO OUT jack
(75
(75
Ω
terminated)
Instrument
Oscilloscope
Adjusting element
RV401 (MB board)
Specification
1.0 ± 0.02 Vp-p
Procedure:
1. Select the initial menu “6. Video Level Adjustment” in the test
1. Select the initial menu “6. Video Level Adjustment” in the test
mode so that color bars are generated. (Refer to “4-9. VIDEO
LEVEL ADJUSTMENT” on page 16)
LEVEL ADJUSTMENT” on page 16)
2. Adjust the RV401 to attain 1.0 ± 0.02 Vp-p.
Figure 5-1
S-terminal Output Check
<Purpose>
Check S-terminal video output. If it is incorrect, pictures will not
be displayed correctly in spite of connection to the TV with a S-
terminal cable.
Check S-terminal video output. If it is incorrect, pictures will not
be displayed correctly in spite of connection to the TV with a S-
terminal cable.
Mode
Video level adjustment in test mode
Signal
Color bars
Test point
S VIDEO OUT jack
(75
(75
Ω
terminated)
Instrument
Oscilloscope
Specification
1.0 ± 0.1 Vp-p
1.0 ± 0.02 Vp-p
1.0 ± 0.1 Vp-p
Procedure:
1. Select the initial menu “6. Video Level Adjustment” in the test
1. Select the initial menu “6. Video Level Adjustment” in the test
mode so that color bars are generated. (Refer to “4-9. VIDEO
LEVEL ADJUSTMENT” on page 16)
LEVEL ADJUSTMENT” on page 16)
2. Confirm that the S-Y level is 1.0 ± 0.1 Vp-p.
Figure 5-2
Click on the first or last page to see other HCD-ZX70DVD service manuals if exist.