HCD-RG60, MHC-RG60 - Sony Audio Service Manual (repair manual)

hcd-rg60, mhc-rg60 service manual
Model
HCD-RG60 MHC-RG60
Pages
58
Size
5.68 MB
Type
PDF
Document
Service Manual
Brand
Device
Audio
File
hcd-rg60-mhc-rg60.pdf
Date

Read Sony HCD-RG60 / MHC-RG60 Service Manual online

HCD-RG60
AEP Model
UK Model
SERVICE MANUAL
MINI HI-FI COMPONENT SYSTEM
Ver 1.2  2003.12
Sony Corporation
Home Audio Company
Published by Sony Engineering Corporation
9-873-193-03
2003L02-1
© 2003.12
• HCD-RG60 is the tuner, deck, CD
and amplifier section in MHC-
RG60.
Model Name Using Similar Mechanism
HCD-DX30/RG40
CD
CD Mechanism Type
CDM58B-K6BD38
Section
Base Unit Name
BU-K6BD38
Optical Pick-up Name
KSM-213DAP
Tape deck
Model Name Using Similar Mechanism
HCD-DX30/RG40
Section
— Continued on next page —
SPECIFICATIONS
Amplifier section
DIN power output (rated) 80 + 80 watts
(6 ohms at 1 kHz, DIN)
Continuous RMS power output (reference)
100 + 100 watts (6 ohms
at 1 kHz, 10% THD)
Music power output (reference)
180 + 180 watts (6 ohms
at 1 kHz, 10% THD)
Inputs
MD/VIDEO (AUDIO) IN (phono jacks):
voltage 450/250 mV,
impedance 47 kilohms
GAME (AUDIO) IN (phono jack):
voltage 450 mV,
impedance 47 kilohms
MIC (mini jack):
sensitivity 1 mV,
impedance 10 kilohms
Outputs
PHONES (stereo mini jack):
accepts headphones of
8 ohms or more
FRONT SPEAKER:
accepts impedance of 6 to
16 ohms
SURROUND SPEAKER accepts impedance of 6 to
16 ohms
CD player section
System
Compact disc and digital
audio system
Laser
Semiconductor laser
(
λ =780 nm)
Emission duration:
continuous
Laser output
Max. 44.6 
µW*
*This output is the value
measured at a distance of
200 mm from the
objective lens surface on
the Optical Pick-up Block
with 7 mm aperture.
Frequency response
2 Hz – 20 kHz (
±0.5 dB)
Wavelength
780 – 790 nm
Signal-to-noise ratio
More than 90 dB
Dynamic range
More than 90 dB
CD OPTICAL DIGITAL OUT
(Square optical connector jack, rear panel)
Wavelength
660 nm
Output Level
–18 dBm
2
HCD-RG60
This appliance is classified as a CLASS 1 LASER product. The
CLASS 1 LASER PRODUCT MARKING is located on the rear
exterior.
Laser component in this product is capable
of emitting radiation exceeding the limit for
Class 1.
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous radia-
tion exposure.
Notes on chip component replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be
damaged by heat.
Flexible Circuit Board Repairing
• Keep the temperature of soldering iron around 270˚C
during repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.
NOTES  ON  HANDLING  THE  OPTICAL  PICK-UP
BLOCK  OR  BASE  UNIT
The laser diode in the optical pick-up block may suffer electrostatic
break-down because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled with
care.
NOTES  ON  LASER  DIODE  EMISSION  CHECK
The laser beam on this model is concentrated so as to be focused on
the disc reflective surface by the objective lens in the optical pick-
up block. Therefore, when checking the laser diode emission, ob-
serve from more than 30 cm away from the objective lens.
Tape deck section
Recording system
4-track 2-channel stereo
Frequency response
40 – 13,000 Hz (
±3 dB),
using Sony TYPE I
cassette
Tuner section
FM stereo, FM/AM superheterodyne tuner
FM tuner section
Tuning range                       87.5 – 108.0 MHz
Antenna
FM lead antenna
Antenna terminals
75 ohm unbalanced
Intermediate frequency
10.7 MHz
AM tuner section
Tuning range
531 – 1,602 kHz (with the
interval set at 9 kHz)
Antenna
AM loop antenna
Antenna terminals
External antenna terminal
Intermediate frequency
450 kHz
General
Power requirements
230 V AC, 50/60 Hz
Power consumption
175 watts
0.5 watts (at the Power
Saving Mode)
Dimensions (w/h/d)
Approx. 280 x   325  x  421 mm
Mass
Approx. 10.0 kg
Supplied accessories:
AM loop antenna (1)
Remote Commander (1)
Batteries (2)
FM lead antenna (1)
Front speaker pads (8)
Design and specifications are subject to change
without notice.
3
HCD-RG60
TABLE OF CONTENTS
1. SERVICE NOTE
.............................................................. 4
2. GENERAL
......................................................................... 5
3. DISASSEMBY
................................................................. 7
4. TEST MODE
................................................................... 13
5. ELECTRICAL ADJUSTMENTS
.............................. 17
6. DIAGRAMS
6-1.
Circuit Board Location ..................................................... 19
6-2.
Block Diagrams  –Tuner Section– ................................... 20
Block Diagrams  –Main Section– .................................... 21
6-3.
Printed Wiring Board  –BD Section– ............................... 22
6-4.
Schematic Diagram  –BD Section– .................................. 23
6-5.
Printed Wiring Board  –Main Section– ............................ 24
6-6.
Schematic Diagram  –Main Section (1/5) – ..................... 25
6-7.
Schematic Diagram  –Main Section (2/5) – ..................... 26
6-8.
Schematic Diagram  –Main Section (3/5) – ..................... 27
6-9.
Schematic Diagram  –Main Section (4/5) – ..................... 28
6-10. Schematic Diagram  –Main Section (5/5) – ..................... 29
6-11. Printed Wiring Board  –Power AMP Section– ................. 30
6-12. Schematic Diagram  –Power AMP Section– ..................... 31
6-13. Printed Wiring Board  –Panel Section– ............................ 32
6-14. Schematic Diagram  –Panel Section– ............................... 33
6-15. Printed Wiring Board  –Trans Section– ............................ 34
6-16. Schematic Diagram  –Trans Section– ............................... 35
6-17. Printed Wiring Board  –Driver Section– ........................... 36
6-18. Schematic Diagram  –Driver Section– .............................. 36
6-19. IC Pin Function Description ............................................. 37
6-20. IC Block Diagrams ............................................................ 40
7. EXPLODED VIEWS
7-1.
Main Section ..................................................................... 43
7-2.
Front Panel Section .......................................................... 44
7-3.
Chassis Section ................................................................. 45
7-4.
CD Mechanism Deck Section .......................................... 46
8. ELECTRICAL PARTS LIST
...................................... 47
4
HCD-RG60
SECTION 1
SERVICE NOTE
1
Connector 
      13p (CN712)
2
Cut the seven melted-connection points
     with a cutting plier.
4
Cut the six melted-connection points
     with a cutting plier.
3
Panel board
5
Key board
Panel board
(ten screw holes)
Key board
(eight screw holes)
Screw hole
In order to re-install the panel board and the key board,
fix them by using the screws (+BVTP 2.6
 
× 
8 ) respectively.
Screw in to the respective screw holes.
Do not tighten the screws excessively.
* The panel board and the key board only are connected to the front panel
  by means of hot-melting the plastics.
Note for installing the panel board and the key board
REMOVING THE PANEL BOARD AND THE KEY BOARD
Hot melt
Page of 58
Display

Download Sony HCD-RG60 / MHC-RG60 Service Manual (Repair Manual)

Here you can read online and download Sony HCD-RG60 / MHC-RG60 Service Manual in PDF. HCD-RG60 / MHC-RG60 service manual will guide through the process and help you recover, restore, fix, disassemble and repair Sony HCD-RG60 / MHC-RG60 Audio. Information contained in service manuals typically includes schematics / circuit diagrams, wiring diagrams, block diagrams, printed wiring boards, exploded views, parts list, disassembly / assembly, pcb.