Read Sony HCD-LV100AV / LBT-LV100AV Service Manual online
3
TABLE OF CONTENTS
1. GENERAL
......................................................................
4
2. DISASSEMBLY
.............................................................
7
3. SERVICE MODE
.......................................................... 11
4. MECHANICAL ADJUSTMENTS
............................ 15
5. ELECTRICAL ADJUSTMENTS
............................. 15
6. DIAGRAMS
6-1. Circuit Boards Location ·············································· 20
6-2. Block Diagrams ··························································· 21
6-3. Schematic Diagram Video Board (1/2) ··················· 25
6-4. Schematic Diagram Video Board (2/2) ··················· 26
6-5. Printed Wiring Board Video Board ························· 27
6-6. Printed Wiring Board BD Board ····························· 28
6-7. Schematic Diagam BD Board ································· 29
6-8. Printed Wiring Baord CD Motor Section ················ 30
6-9. Schematic Diagram CD Motor Section ··················· 31
6-10. Printed Wiring Board Audio Board ························· 32
6-11. Schematic Diagram Audio Board ···························· 33
6-12. Printed Wiring Board Leaf SW Board ···················· 34
6-13. Schematic Diagram Leaf SW Board ······················· 34
6-14. Printed Wiring Board Main Board ·························· 35
6-15. Schematic Diagram Main Board (1/3) ···················· 36
6-16. Schematic Diagram Main Board (2/3) ···················· 37
6-17. Schematic Diagram Main Board (3/3) ···················· 38
6-18. Printed Wiring Board Panel FL Board ···················· 40
6-19. Schematic Diagram Panel FL Board ······················· 41
6-20. Printed Wiring Board Panel VR Board ···················· 42
6-21. Schematic Diagram Panel VR Board ······················ 43
6-22. Printed Wiring Board
6-2. Block Diagrams ··························································· 21
6-3. Schematic Diagram Video Board (1/2) ··················· 25
6-4. Schematic Diagram Video Board (2/2) ··················· 26
6-5. Printed Wiring Board Video Board ························· 27
6-6. Printed Wiring Board BD Board ····························· 28
6-7. Schematic Diagam BD Board ································· 29
6-8. Printed Wiring Baord CD Motor Section ················ 30
6-9. Schematic Diagram CD Motor Section ··················· 31
6-10. Printed Wiring Board Audio Board ························· 32
6-11. Schematic Diagram Audio Board ···························· 33
6-12. Printed Wiring Board Leaf SW Board ···················· 34
6-13. Schematic Diagram Leaf SW Board ······················· 34
6-14. Printed Wiring Board Main Board ·························· 35
6-15. Schematic Diagram Main Board (1/3) ···················· 36
6-16. Schematic Diagram Main Board (2/3) ···················· 37
6-17. Schematic Diagram Main Board (3/3) ···················· 38
6-18. Printed Wiring Board Panel FL Board ···················· 40
6-19. Schematic Diagram Panel FL Board ······················· 41
6-20. Printed Wiring Board Panel VR Board ···················· 42
6-21. Schematic Diagram Panel VR Board ······················ 43
6-22. Printed Wiring Board
TC-A/TC-B/CD-L/CD-L2/CD-R/CD-R2 Boards ······· 44
6-23. Schematic Diagram
TC-A/TC-B/CD-L/CD-L2/CD-R/CD-R2 Boards ······· 45
6-24. Printed Wiring Board
Front Input/Headphone/MIC Boards ··························· 46
6-25. Schematic Diagram
Front Input/Headphone/MIC Boards ··························· 47
6-26. Printed Wiring Board PA Board ······························ 48
6-27. Schematic Diagram PA Board ································· 49
7-28. Printed Wiring Board Surround Board ···················· 50
6-29. Schematic Diagram Surround Board ······················· 51
6-30. Printed Wiring Board Trans/Sub Trans Boards ······· 52
6-31. Schematic Diagram Trans/Sub Ttrans Boards ········· 53
6-32. IC Block Diagrams ······················································ 54
6-33. IC Pin Function Description ········································ 56
6-27. Schematic Diagram PA Board ································· 49
7-28. Printed Wiring Board Surround Board ···················· 50
6-29. Schematic Diagram Surround Board ······················· 51
6-30. Printed Wiring Board Trans/Sub Trans Boards ······· 52
6-31. Schematic Diagram Trans/Sub Ttrans Boards ········· 53
6-32. IC Block Diagrams ······················································ 54
6-33. IC Pin Function Description ········································ 56
7. EXPLODED VIEWS
................................................... 64
8. ELECTRICAL PARTS LIST
................................... 72
This appliance is classified as a CLASS 1 LASER product.
The CLASS 1 LASER PRODUCT MARKING is located on
the rear exterior.
The CLASS 1 LASER PRODUCT MARKING is located on
the rear exterior.
Laser component in this product is capable of emitting radiation
exceeding the limit for Class 1.
exceeding the limit for Class 1.
The following caution label is located inside the unit.
The laser diode in the optical pick-up block may suffer electrostatic
break-down because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled with
care.
break-down because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled with
care.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused on
the disc reflective surface by the objective lens in the optical pick-
up block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.
The laser beam on this model is concentrated so as to be focused on
the disc reflective surface by the objective lens in the optical pick-
up block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.
Notes on chip component replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be dam-
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be dam-
aged by heat.
Flexible Circuit Board Repairing
• Keep the temperature of the soldering iron around 270 ˚C dur-
• Keep the temperature of the soldering iron around 270 ˚C dur-
ing repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.
NOTES ON HANDLING THE OPTICAL PICK-UP
BLOCK OR BASE UNIT
BLOCK OR BASE UNIT
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous
radiation exposure.
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous
radiation exposure.
Click on the first or last page to see other HCD-LV100AV / LBT-LV100AV service manuals if exist.