Read Sony HCD-GZR88D / HCD-GZR99D / MHC-GZR88D / MHC-GZR99D Service Manual online
SERVICE MANUAL
Sony Corporation
Published by Sony Techno Create Corporation
HCD-GZR88D/GZR99D
HCD-GZR88D/GZR99D: E3, E4, E15, EA, PH, SP Model
DVD DECK RECEIVER
HCD-GZR99D: E2, E51, AR, MX Model
DVD RECEIVER
9-889-536-03
2011I33-1
©
2011.09
E Model
Ver. 1.2 2011.09
• HCD-GZR88D/GZR99D are the tuner,
deck, DVD and amplifi er section
in
deck, DVD and amplifi er section
in
MHC-GZR88D/GZR99D.
DVD
Section
Section
Model Name Using Similar Mechanism
HCD-GZR77D
DVD Mechanism Type
CDM74HF-DVBU101
Optical Pick-up Name
KHM-313CAB
Tape Deck
Section
Section
Model Name Using Similar Machanism
HCD-GZR77D
Tape Transport Mechanism Type
CWP42FR605
SPECIFICATIONS
Amplifi er Section
The following measured at AC 127 V, 60 Hz (Mexican model)
The following measured at AC 127, 220, 240 V, 50/60 Hz
(Saudi Arabian model)
The following measured at AC 120, 220, 240 V, 50/60 Hz (Other models)
MHC-GZR99D
Power output (rated):
135 W + 135 W
(at
6
, 1 kHz, 1% THD, at LINK MODE)
RMS output power (reference)
Front speaker:
Front speaker:
175 W + 175 W
(per channel at 8
, 1 kHz, 10% THD)
Satellite speaker:
70 W + 70 W
(per channel at 24
, 1 kHz, 10% THD)
Subwoofer:
210 W (at 6
, 100 Hz, 10% THD)
MHC-GZR88D
Power output (rated):
125 W + 125 W
(at
6
, 1 kHz, 1% THD, at LINK MODE)
RMS output power (reference)
Front speaker:
Front speaker:
175 W + 175 W
(per channel at 8
, 1 kHz, 10% THD)
Satellite speaker:
70 W + 70 W
(per channel at 24
, 1 kHz, 10% THD)
– Continued on next page –
Photo: HCD-GZR99D: E2 model
HCD-GZR88D/GZR99D
2
SAFETY-RELATED COMPONET WARNING!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE
WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS
WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS
WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS
MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
Inputs
VIDEO/SAT VIDEO IN (phono jack):
1 Vp-p, 75 ohms
VIDEO/SAT AUDIO IN L/R (phono jacks):
voltage 250/450 mV, impedance 47 kilohms
MIC 1/MIC 2 (phone jacks):
sensitivity 1 mV, impedance 10 kilohms
Outputs
VIDEO OUT (phono jack):
max. output level 1 Vp-p, unbalanced,
Sync negative, load impedance 75 ohms
COMPONENT VIDEO OUT:
Y: 1 Vp-p, 75 ohms
P
B
/C
B
: 0.7 Vp-p, 75 ohms
P
R
/C
R
: 0.7 Vp-p, 75 ohms
DVD DIGITAL OUT (Square optical connector jack, rear panel):
Wavelength 650 nm
PHONES (stereo mini jack):
accepts headphones of 8 ohms or more
SUBWOOFER OUT (MHC-GZR88D only):
Voltage 1 V, impedance 1 kilohm
FRONT SPEAKER:
Use only the supplied speaker SS-GZR99D.
SATELLITE SPEAKER: Use only the supplied speaker SS-RSX99D.
SUBWOOFER (MHC-GZR99D only):
SUBWOOFER (MHC-GZR99D only):
Use only the supplied subwoofer
SS-WGV99D.
(USB) port: Type A (1)
Maximum current: 500 mA
Disc player section
System:
Compact disc and digital audio and video
system
Laser Diode Properties
Emission
Laser Diode Properties
Emission
duration:
Continuous Laser Output*:
Less than 44.6
μW
*This output is the value measurement
at a distance of 200mm from the objective
lens surface on the Optical Pick-up Block
with 7mm aperture.
Frequency response
DVD (PCM 48 kHz):
DVD (PCM 48 kHz):
2 Hz
− 22 kHz (±1 dB)
CD: 2
Hz
− 20 kHz (±0.5 dB)
Video color system format
Latin American model:
Latin American model:
NTSC
Other models:
NTSC and PAL
Tape deck section (except for Latin American models)
Recording system:
4-track 2-channel, stereo
Tuner section
FM stereo, FM/AM superheterodyne tuner
FM tuner section
Tuning range:
FM tuner section
Tuning range:
87.5
− 108.0 MHz (50 kHz step)
Antenna:
FM lead antenna
Antenna terminals: 75
Ω unbalanced
Intermediate frequency:
10.7
10.7
MHz
AM tuner section
Tuning range:
Saudi Arabian models:
531
Tuning range:
Saudi Arabian models:
531
− 1,602 kHz (9 kHz step)
Latin American model:
530 – 1,710 kHz (with 10 kHz tuning interval)
531 – 1,710 kHz (with 9 kHz tuning interval)
Other models:
531 – 1,602 kHz (with 9 kHz tuning interval)
530 – 1,610 kHz (with 10 kHz tuning interval)
Antenna:
AM loop antenna
Antenna terminals: External antenna terminal
Intermediate frequency:
450
Intermediate frequency:
450
kHz
General
Power requirements
Argentine and Thai models:
Argentine and Thai models:
AC 220 V, 50/60 Hz
Saudi Arabian model:
AC
AC
120
− 127, 220, 230 − 240 V, 50/60 Hz,
adjustable with voltage selector
Mexican model:
AC 127 V, 60 Hz,
Other models:
AC 120, 220, 230
− 240 V, 50/60 Hz,
adjustable with voltage selector
Power consumption
MHC-GZR99D: 215
MHC-GZR99D: 215
W
MHC-GZR88D: 170
W
Dimensions (w/h/d) (excl. speakers):
Approx.
Approx.
280
× 326 × 440 mm
Mass (excl. speakers)
MHC-GZR99D:
MHC-GZR99D:
Approx. 13.2 kg (Latin American models),
approx.13.7 kg (other models)
MHC-GZR88D:
Approx. 13.2 kg
Design and specifi cations are subject to change without notice.
Ver. 1.1
HCD-GZR88D/GZR99D
3
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40 °C higher
• Unleaded solder melts at a temperature about 40 °C higher
than ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350 °C.
Caution: The printed pattern (copper foil) may peel away if
about 350 °C.
Caution: The printed pattern (copper foil) may peel away if
the heated tip is applied for too long, so be careful!
• Strong
viscosity
Unleaded solder is more viscous (sticky, less prone to fl ow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
•
Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
also be added to ordinary solder.
NOTES ON CHIP COMPONENT REPLACEMENT
•
•
Never reuse a disconnected chip component.
•
Notice that the minus side of a tantalum capacitor may be dam-
aged by heat.
aged by heat.
FLEXIBLE CIRCUIT BOARD REPAIRING
•
•
Keep the temperature of soldering iron around 270 °C during
repairing.
repairing.
•
Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
circuit board (within 3 times).
•
Be careful not to apply force on the conductor when soldering
or unsoldering.
or unsoldering.
Laser component in this product is capable of emitting radiation
exceeding the limit for Class 1.
exceeding the limit for Class 1.
This appliance is classifi ed as
a CLASS 1 LASER product.
This marking is located on the
rear exterior.
a CLASS 1 LASER product.
This marking is located on the
rear exterior.
CAUTION
Use of controls or adjustments or performance of procedures
other than those specifi ed herein may result in hazardous radia-
tion exposure.
Use of controls or adjustments or performance of procedures
other than those specifi ed herein may result in hazardous radia-
tion exposure.
NOTES ON HANDLING THE OPTICAL PICK-UP
BLOCK OR BASE UNIT
BLOCK OR BASE UNIT
The laser diode in the optical pick-up block may suffer electrostat-
ic break-down because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The fl exible board is easily damaged and should be handled with
care.
ic break-down because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The fl exible board is easily damaged and should be handled with
care.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused
on the disc refl ective surface by the objective lens in the optical
pickup block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.
The laser beam on this model is concentrated so as to be focused
on the disc refl ective surface by the objective lens in the optical
pickup block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.
HCD-GZR88D/GZR99D
4
Model
Parts No.
GZR88D: E3, E15
4-133-526-0[]
GZR88D: E4
4-133-526-1[]
GZR88D: E12
4-133-526-2[]
GZR88D: SP
4-133-526-3[]
GZR88D: TH
4-133-526-4[]
GZR88D: PH
4-133-526-5[]
GZR88D: EA
4-133-526-6[]
GZR99D: E3, E15
4-133-527-0[]
GZR99D: E4
4-133-527-1[]
GZR99D: SP
4-133-527-2[]
GZR99D: PH
4-133-527-3[]
GZR99D: E2, E51
4-133-527-4[]
GZR99D: AR
4-133-527-6[]
GZR99D: MX
4-133-527-7[]
GZR99D: EA
4-133-527-9[]
MODEL IDENTIFICATION
– Back Panel –
– Back Panel –
• Abbreviation
E3
E3
: 240V AC area in E model
E15
: Iran model
E4
: 110 – 120V/220 – 240V AC area in E model
E12
: 220 – 240V AC area in E model
SP
: Singapore model
TH :
Thai
model
PH
: Philippines model
EA
: Saudi Arabia model
E2
: 120V AC area in E model
E51
: Chilean and Peruvian model
MX
: Mexican model
AR :
Argentina
model
Parts No.
Ver. 1.1
