Read Sony HCD-GZR5D / MHC-GZR5D Service Manual online
HCD-GZR5D
2
NOTES ON CHIP COMPONENT REPLACEMENT
•
•
Never reuse a disconnected chip component.
•
Notice that the minus side of a tantalum capacitor may be dam-
aged by heat.
aged by heat.
FLEXIBLE CIRCUIT BOARD REPAIRING
•
•
Keep the temperature of soldering iron around 270 °C during
repairing.
repairing.
•
Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
circuit board (within 3 times).
•
Be careful not to apply force on the conductor when soldering
or unsoldering.
or unsoldering.
SAFETY-RELATED COMPONET WARNING!
COMPONENTS IDENTIFIED BY MARK
0 OR DOTTED LINE
WITH MARK
0 ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS
REPLACE THESE COMPONENTS WITH SONY PARTS
WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS
MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
Tuner section
FM stereo, FM/AM superheterodyne tuner
FM stereo, FM/AM superheterodyne tuner
FM tuner section
Tuning range:
Tuning range:
87.5 – 108.0 MHz (50 kHz step)
Antenna:
FM lead antenna
Antenna terminals:
75 ohms unbalanced
Intermediate frequency: 10.7 MHz
AM tuner section
Tuning range:
Tuning range:
European, Russian and Saudi Arabian models:
531 – 1,602 kHz (9 kHz step)
Other
models:
531 – 1,602 kHz (with 9 kHz tuning interval)
530 – 1,610 kHz (with 10 kHz tuning interval)
Antenna:
AM loop antenna
Antenna terminals:
External antenna terminal
Intermediate frequency: 450 kHz
General
Power requirements
European and Russian models:
Power requirements
European and Russian models:
AC 230 V, 50/60 Hz
Saudi Arabian model:
AC 120 – 127, 220 – 240 V
50/60 Hz, adjustable with voltage selector
Thai model:
AC 220 V, 50/60 Hz
Other models:
AC 120, 220, 230 – 240 V, 50/60 Hz, adjustable
with voltage selector
Power consumption:
190 W
Dimensions (w/h/d) (excl. speakers):
Approx. 200 × 306 × 415 mm
Mass (excl. speakers): Approx. 7.9 kg
Design and specifi cations are subject to change without notice.
NOTES ON HANDLING THE OPTICAL PICK-UP
BLOCK OR BASE UNIT
The laser diode in the optical pick-up block may suffer electrostat-
ic break-down because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The fl exible board is easily damaged and should be handled with
care.
ic break-down because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The fl exible board is easily damaged and should be handled with
care.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused
on the disc refl ective surface by the objective lens in the optical
pickup block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.
The laser beam on this model is concentrated so as to be focused
on the disc refl ective surface by the objective lens in the optical
pickup block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.
LASER DIODE AND FOCUS SEARCH OPERATION
CHECK
Carry out the “S curve check” in “CD section adjustment” and
check that the S curve waveform is output several times.
CHECK
Carry out the “S curve check” in “CD section adjustment” and
check that the S curve waveform is output several times.
CAUTION
Use of controls or adjustments or performance of procedures
other than those specifi ed herein may result in hazardous radia-
tion exposure.
Use of controls or adjustments or performance of procedures
other than those specifi ed herein may result in hazardous radia-
tion exposure.
This appliance is classifi ed as
a CLASS 1 LASER product.
This marking is located on the
rear or bottom exterior.
a CLASS 1 LASER product.
This marking is located on the
rear or bottom exterior.
Ver. 1.1
Click on the first or last page to see other HCD-GZR5D / MHC-GZR5D service manuals if exist.