Read Sony HCD-GTX66 / HCD-GTX77 / HCD-GTX77BP / MHC-GTX66 / MHC-GTX77 / MHC-GTX77BP Service Manual online
1
Ver. 1.1 2008. 03
Model Name Using Similar Mechanism
HCD-GTX88
CD
CD Mechanism Type
CDM74KF-K6BD91UR-WOD
Section
Optical Pick-up Name
KSM-213DCP/C2NP
Tape Deck
Model Name Using Similar Machanism
HCD-GTX88
Section
SERVICE MANUAL
HCD-GTX66/GTX77/
GTX77BP
Amplifier section
The following are measured at
Mexican model:
Mexican model:
HCD-GTX77BP: AC 127 V, 60 Hz
Other models:
AC 120, 220, 240 V, 50/60 Hz
Front speaker
Power Output (rated):
Power Output (rated):
HCD-GTX77/GTX77BP: 225 W + 225 W
(at 4
(at 4
Ω, 1 kHz, 1% THD)
HCD-GTX66: 210 W + 210 W
(at 4
(at 4
Ω, 1 kHz, 1% THD)
RMS output power (reference):
HCD-GTX77/GTX77BP: 380 W + 380 W
(per channel at 4
(per channel at 4
Ω, 1 kHz,
10% THD)
HCD-GTX66: 340 W + 340 W
(per channel at 4
HCD-GTX66: 340 W + 340 W
(per channel at 4
Ω, 1 kHz,
10% THD)
Inputs
VIDEO (AUDIO IN) L/R:
VIDEO (AUDIO IN) L/R:
Voltage 250 mV,
impedance 47 kilohms
impedance 47 kilohms
AUDIO (AUDIO IN) L/R:
Voltage 450 mV,
impedance 47 kilohms
impedance 47 kilohms
MIC:
Sensitivity 1 mV,
impedance 10 kilohms
impedance 10 kilohms
(USB) port:
Type A
Outputs
PHONES:
PHONES:
accepts headphones of
8 ohms or more
8 ohms or more
SPECIFICATIONS
Disc player section
System
Compact disc and digital
audio system
audio system
Laser
Semiconductor laser
(
(
λ=770 – 810 nm)
Emission duration:
continuous
continuous
Laser Output
Max. 44.6 µW*
* This output is the value measured
at a distance of 200 mm from the
objective lens surface on the Optical
Pick-up Block with 7 mm aperture.
* This output is the value measured
at a distance of 200 mm from the
objective lens surface on the Optical
Pick-up Block with 7 mm aperture.
Frequency response
20 Hz – 20 kHz
Wave length
770 – 810 nm
Signal-to-noise ratio
More than 90 dB
Dynamic range
More than 88 dB
Tape deck section
Recording system
4-track 2-channel stereo
Frequency response
50 – 13,000 Hz (±3 dB),
using Sony TYPE I tape
using Sony TYPE I tape
Sony Corporation
Audio Business Group
Published by Sony Techno Create Corporation
9-887-780-02
2008C04-1
© 2008. 03
– Continued on next page –
CD DECK RECEIVER
• HCD-GTX66/GTX77/GTX77BP are the
tuner,deck, CD and amplifier section in
MHC-GTX66/GTX77/GTX77BP.
MHC-GTX66/GTX77/GTX77BP.
E Model
HCD-GTX66/GTX77
Mexican Model
HCD-GTX77BP
Photo: HCD-GTX66
2
HCD-GTX66/GTX77/GTX77BP
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK
0
OR DOTTED LINE
WITH MARK
0
ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE
PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR
IN SUPPLEMENTS PUBLISHED BY SONY.
REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE
PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR
IN SUPPLEMENTS PUBLISHED BY SONY.
Tuner section
FM stereo, FM/AM superheterodyne tuner
FM tuner section
Tuning range
87.5 – 108.0 MHz
(50 kHz step)
(50 kHz step)
Antenna
FM lead antenna
Antenna terminals
75 ohm unbalanced
Intermediate frequency 10.7 MHz
AM tuner section
Tuning range
Latin American models:
Latin American models:
530 – 1,710 kHz (with the
interval set at 10 kHz)
531 – 1,710 kHz (with the
interval set at 9 kHz)
interval set at 10 kHz)
531 – 1,710 kHz (with the
interval set at 9 kHz)
Other models:
531 – 1,602 kHz (with the
interval set at 9 kHz)
530 – 1,610 kHz (with the
interval set at 10 kHz)
interval set at 9 kHz)
530 – 1,610 kHz (with the
interval set at 10 kHz)
Antenna
AM loop antenna
Antenna terminals
External antenna terminal
Intermediate frequency 450 kHz
USB section
Supported bit rate
MP3 (MPEG 1 Audio Layer 3):
32 – 320 kbps, VBR
32 – 320 kbps, VBR
Sampling frequencies
MP3 (MPEG 1 Audio Layer 3):
32/44.1/48 kHz
32/44.1/48 kHz
Transfer speed
Full-Speed
Supported USB device
Mass Storage Class
Maximum current
500 mA
General
Power requirements
Mexican model:
Mexican model:
127 V AC, 60 Hz
Argentina model:
220 V AC, 50/60 Hz
Other models:
120 V, 220 V or 230 – 240 V AC,
50/60 Hz, adjustable with
voltage selector
50/60 Hz, adjustable with
voltage selector
Power consumption
300 W
Dimensions (w/h/d) (Approx.)
281
×
361
×
417 mm
Mass (Approx.)
12.4 kg
Design and specifications are subject to change without
notice.
notice.
Ver. 1.1
3
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous
radiation exposure.
other than those specified herein may result in hazardous
radiation exposure.
HCD-GTX66/GTX77/GTX77BP
NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK
OR BASE UNIT
OR BASE UNIT
The laser diode in the optical pick-up block may suffer electrostatic
breakdown because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled with
care.
breakdown because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled with
care.
Notes on Chip Component Replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be
• Notice that the minus side of a tantalum capacitor may be
damaged by heat.
Flexible Circuit Board Repairing
• Keep the temperature of soldering iron around 270°C during
repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40 °C higher than
• Unleaded solder melts at a temperature about 40 °C higher than
ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to about
350 °C.
Caution: The printed pattern (copper foil) may peel away if the
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to about
350 °C.
Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!
• Strong viscosity
Unleaded solder is more viscou-s (sticky, less prone to flow) than
ordinary solder so use caution not to let solder bridges occur such
as on IC pins, etc.
ordinary solder so use caution not to let solder bridges occur such
as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may also
be added to ordinary solder.
be added to ordinary solder.
This appliance is
claassified as a CLASS 1
LASER product. This
label is located on the
rear exterior.
claassified as a CLASS 1
LASER product. This
label is located on the
rear exterior.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused on
the disc reflective surface by the objective lens in the optical pick-
up block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.
the disc reflective surface by the objective lens in the optical pick-
up block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.
Laser component in this product is capable
of emitting radiation exceeding the limit for
Class 1.
of emitting radiation exceeding the limit for
Class 1.
4
HCD-GTX66/GTX77/GTX77BP
MODEL IDENTIFICATION
– MODEL NUMBER LABEL –
MODEL
PARTS No.
GTX66
AR
3-198-001-2
s
E2
3-113-126-2
s
E51
3-198-009-2
s
GTX77
AR
3-198-001-1
s
E2
3-113-126-1
s
E51
3-198-009-1
s
GTX77BP
MX
3-113-127-1
s
• Abbreviation
AR
: Argentina model
E2
: 120V AC area in E model
E51 : Chilean and Peruvian model
MX
MX
: Mexican Model
PART No.
Ver. 1.1