Read Sony HCD-GTR33 / HCD-GTR55 / HCD-GTR77 / MHC-GTR33 / MHC-GTR55 / MHC-GTR77 Service Manual online
HCD-GTR33/GTR55/GTR77
4
HOW TO OPEN THE TRAY WHEN POWER SWITCH TURN OFF
Step: 1) Work after removing the case (side-R and side-L) referring to “2.2. CASE(SIDE-L/R)” on disassembly (page 5).
2) Work after removing the top case referring to “2-3. TOP CASE” on disassembly (page 6).
lever
d
Turn a gear by
a driver till a lever
rises up to the
position of the figure.
(Try to push gear at the
same time slowly pull
Front panel away.)
rises up to the
position of the figure.
(Try to push gear at the
same time slowly pull
Front panel away.)
state of opening the CD tray
a
e
c
c
b
gear
PRECAUTION WHEN INSTALLING A NEW OP UNIT/
PRECAUTION BEFORE UNSOLDERING THE STATIC
ELECTRICITY PREVENTION SOLDER BRIDGE
PRECAUTION BEFORE UNSOLDERING THE STATIC
ELECTRICITY PREVENTION SOLDER BRIDGE
When installing a new OP unit, be sure to connect the fl ex-
ible printed circuit board fi rst of all before removing the static
electricity prevention solder bridge by unsoldering.
Remove the static electricity prevention solder bridge by unsolder-
ing after the fl exible printed circuit board has already been con-
nected.
(Do not remove nor unsolder the solder bridge as long as the OP
unit is kept standalone.)
ible printed circuit board fi rst of all before removing the static
electricity prevention solder bridge by unsoldering.
Remove the static electricity prevention solder bridge by unsolder-
ing after the fl exible printed circuit board has already been con-
nected.
(Do not remove nor unsolder the solder bridge as long as the OP
unit is kept standalone.)
Ver. 1.4
NOTE OF REPLACING THE IC800 ON THE POWER
BOARD FOR HCD-GTR55/GTR77
Take note for HCD-GTR55/GTR77 set as listed below:
a) For all serial number of HCD-GTR55/GTR77
Take note for HCD-GTR55/GTR77 set as listed below:
a) For all serial number of HCD-GTR55/GTR77
(AR, E2, E51 and MX)
b) For serial number which is before S 011206151 of
HCD-GTR55
HCD-GTR55
(E4)
c) For serial number which is before S 011206641 of
HCD-GTR77
HCD-GTR77
(E4)
The IC800 is limited to the stock quantity of service parts.
When the IC800 cannot be obtained, exchange the complete
POWER board (refer to Supplement-1).
Moreover, when the complete POWER board is exchanged, you
must also exchange the IC401 on the MAIN board (refer to Sup-
plemetn-1) at the same time.
Refer to Supplement-1 (page 2) for the “REPLACING THE IC800
ON THE POWER BOARD” fl owchart.
When the IC800 cannot be obtained, exchange the complete
POWER board (refer to Supplement-1).
Moreover, when the complete POWER board is exchanged, you
must also exchange the IC401 on the MAIN board (refer to Sup-
plemetn-1) at the same time.
Refer to Supplement-1 (page 2) for the “REPLACING THE IC800
ON THE POWER BOARD” fl owchart.
Note: Refer to Supplement-1 for the servicing notes, printed
wiring board, schematic diagram of POWER board (HCD-
GTR55/GTR77) and electrical part list of POWER board
(HCD-GTR55/GTR77) and MAIN board (HCD-GTR55/
GTR77).
GTR55/GTR77) and electrical part list of POWER board
(HCD-GTR55/GTR77) and MAIN board (HCD-GTR55/
GTR77).
• Abbreviation
AR :
AR :
Argentina
model
E2
: 120V AC area in E model
E4 :
African
model
E51
: Chilean and Peruvian models
MX
: Mexican model
Click on the first or last page to see other HCD-GTR33 / HCD-GTR55 / HCD-GTR77 / MHC-GTR33 / MHC-GTR55 / MHC-GTR77 service manuals if exist.