Read Sony HCD-GRX9000 / HCD-RX900 / MHC-GRX9000 / MHC-RX900 Service Manual online
– 14 –
2. Turn the adjustment screw and check output peaks. If the peaks
do not match for L-CH and R-CH, turn the adjustment screw
so that outputs match within 1dB of peak.
so that outputs match within 1dB of peak.
3. Mode: Playback (FWD)
4. Repeat setps 1 to 3 in playback (REV) mode.
5. After the adjustments, apply suitable locking compound to the
5. After the adjustments, apply suitable locking compound to the
pats adjusted.
Adjustment Location: Playback Head (Deck A).
Record/Playback/Erase Head (Deck B).
Tape Speed Adjustment
DECK B
Note:
Start the Tape Speed adjustment as below after setting to the test
mode.
In the test mode, the tape speed is high during pressing the
mode.
In the test mode, the tape speed is high during pressing the
[HI-DUB]
button.
Procedure:
1. Turn the power switch on.
2. Press the
1. Turn the power switch on.
2. Press the
p button,
[ENTER/NEXT]
button and
[DISC 3]
button
simultaneously.
(The “VOLUME” on the fluorescent indicator tube will blink
while in the test mode.)
To exit from the test mode, press the
(The “VOLUME” on the fluorescent indicator tube will blink
while in the test mode.)
To exit from the test mode, press the
I/
u
button.
Mode: Playback
1. Insert the WS-48B into the deck B.
2. Press the
2. Press the
· button on the deck B.
3. Press the
[HI-DUB]
button in playback mode.
Then at HIGH speed mode.
4. Adjust RV1001 on the LEAF SW board do that frequency
counter reads 6,000 ± 180 Hz.
5. Press the
[HI-DUB]
button.
Then back to NORMAL speed mode.
6. Adjust RV1002 on the LEAF SW board so that frequency
counter reads 3,000 ± 90 Hz.
Adjustment Location: LEAF SW board
Sample value of Wow and Flutter: 0.3% or less W.RMS (JIS)
Sample value of Wow and Flutter: 0.3% or less W.RMS (JIS)
(WS-48B)
Playback level Adjustment
DECK A
DECK B
Procedure:
Mode: Playback
Mode: Playback
Deck A is RV311 (L-CH) and RV411 (R-CH), Deck B is RV301
(L-CH) and RV401 (R-CH) so that adjustment within adjustment
level as follows.
Adjustment Level:
(L-CH) and RV401 (R-CH) so that adjustment within adjustment
level as follows.
Adjustment Level:
CN301 PB level: 301.5 to 338.3 mV (–8.2 to –7.2 dB) level
difference between the channels: within ± 0.5 dB
difference between the channels: within ± 0.5 dB
Adjustment Location: AUDIO board
Screw
position
position
L-CH
peak
peak
within
1dB
1dB
Output
level
level
L-CH
peak
peak
R-CH
peak
peak
within
1dB
1dB
Screw
position
position
R-CH
peak
peak
set
test tape
P-4-A100
(10 kHz, –10 dB)
P-4-A100
(10 kHz, –10 dB)
(pin
1
: R-CH)
oscilloscope
V
H
waveform of oscilloscope
in phase 45
°
90
°
135
°
180
°
good
wrong
(pin
2
: GND)
(pin
3
: L-CH)
MAIN board
CN301
CN301
+
–
–
set
test tape
WS-48B
(3 kHz, 0 dB)
WS-48B
(3 kHz, 0 dB)
MAIN board
CN301 (Pin
CN301 (Pin
3
: L-CH)
(Pin
1
: R-CH)
frequency counter
+
–
–
set
test tape
P-4-L300
(315 Hz, 0 dB)
P-4-L300
(315 Hz, 0 dB)
MAIN board
CN301 (Pin
CN301 (Pin
3
: L-CH)
(Pin
1
: R-CH)
level meter
forward
reverse
Click on the first or last page to see other HCD-GRX9000 / HCD-RX900 / MHC-GRX9000 / MHC-RX900 service manuals if exist.