HCD-GRX5, HCD-RX66, MHC-GRX5, MHC-RX66 - Sony Audio Service Manual (repair manual). Page 3

Read Sony HCD-GRX5 / HCD-RX66 / MHC-GRX5 / MHC-RX66 Service Manual online

– 3 –
TABLE  OF  CONTENTS
1.
SERVICING  NOTES
............................................... 3
2.
GENERAL
Location of Controls ....................................................... 6
Setting the Time .............................................................. 7
3.
DISASSEMBLY
......................................................... 8
4.
TEST  MODE
.............................................................. 11
5.
MECHANICAL  ADJUSTMENTS
....................... 13
6.
ELECTRICAL  ADJUSTMENTS
DECK Section ................................................................. 13
CD Section ...................................................................... 16
7.
DIAGRAMS
................................................................. 18
7-1. Block Diagram
– CD MECHANISM DECK Section – .......................... 19
7-2. Block Diagram
– TAPE DECK Section – ................................................ 21
7-3. Block Diagram
– MAIN Section – ........................................................... 23
7-4. Block Diagram
– DISPLAY/KEY CONTROL/POWER SUPPLY
Section –  ........................................................................ 25
7-5. Printed Wiring Boards  – CD Section – ......................... 29
7-6. Schematic Diagram – CD Section – ............................... 31
7-7. Printed Wiring Board  – CD MOTOR Section – ............ 33
7-8. Schematic Diagram  – CD MOTOR Section – .............. 35
7-9. Printed Wiring Board  – TAPE DECK Section – ........... 37
7-10. Schematic Diagram  – TAPE DECK Section – .............. 39
7-11. Printed Wiring Board  – LEAF SW Section – ............... 41
7-12. Schematic Diagram  – LEAF SW Section – .................. 41
7-13. Printed Wiring Board  – MAIN Section – ...................... 43
7-14. Schematic Diagram
– MAIN Section (1/4) – .................................................. 45
7-15. Schematic Diagram
– MAIN Section (2/4) – .................................................. 47
7-16. Schematic Diagram
– MAIN Section (3/4) – .................................................. 49
7-17. Schematic Diagram
– MAIN Section (4/4) – .................................................. 51
7-18. Printed Wiring Board  – PANEL Section – .................... 53
7-19. Schematic Diagram  – PANEL Section – ....................... 55
7-20. Printed Wiring Board  – CD-SW Section – .................... 57
7-21. Schematic Diagram  – CD-SW Section – ...................... 57
7-22. Printed Wiring Board  – HP Section – ........................... 59
7-23. Schematic Diagram  – HP Section – .............................. 59
7-24. Printed Wiring Board  – POWER AMP Section – ......... 60
7-25. Schematic Diagram  – POWER AMP Section – ............ 61
7-26. Printed Wiring Board
– TRANSFORMER Section – ........................................ 63
7-27. Schematic Diagram
– TRANSFORMER Section – ........................................ 64
7-28. IC Pin Function Description ........................................... 68
8.
EXPLODED  VIEWS
................................................ 73
9.
ELECTRICAL  PARTS  LIST
............................... 82
SECTION  1
SERVICING  NOTES
The laser diode in the optical pick-up block may suffer electro-
static break-down because of the potential difference generated
by the charged electrostatic load, etc. on clothing and the human
body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled with
care.
NOTES  ON  LASER  DIODE  EMISSION  CHECK
The laser beam on this model is concentrated so as to be focused
on the disc reflective surface by the objective lens in the optical
pick-up block. Therefore, when checking the laser diode emis-
sion, observe from more than 30 cm away from the objective lens.
Notes on chip component replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be dam-
aged by heat.
Flexible Circuit Board Repairing
• Keep the temperature of the soldering iron around 270 ˚C dur-
ing repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.
NOTES  ON  HANDLING  THE  OPTICAL  PICK-UP
BLOCK  OR  BASE  UNIT
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous ra-
diation exposure.
This appliance is classified as a CLASS 1 LASER product.
The CLASS 1 LASER PRODUCT MARKING is located on
the rear exterior.
Laser component in this product is capable of emitting radiation
exceeding the limit for Class 1.
The following caution label is located inside the unit.
CAUTION
:
INVISIBLE LASER RADIATION WHEN OPEN AND INTER-
LOCKS DEFEATED.  AVOID EXPOSURE TO BEAM.
ADVARSEL
:
USYNLIG LASERSTRÅLING VED ÅBNING NÅR
SIKKERHEDSAFBRYDERE ER UDE AF FUNKTION. UNDGÅ UDSAETTELSE FOR
STRÅLING.
VORSICHT
:
UNSICHTBARE LASERSTRAHLUNG, WENN ABDECKUNG
GEÖFFNET UND SICHEREITSVERRIEGELUNG ÜBERBRÜCKT. NICHT DEM
STRAHL AUSSETZEN.
VARO
!
:
AVATTAESSA JA SUOJALUKITUS OHITETTAESSA OLET
ALTTIINA NÄKYMÄTTÖMÄLLE LASERSÄTEILYLLE. ÄLÄ KATSO SÄTEESEEN.
VARNING
:
OSYNLING LASERSTRÅLING NÄR DENNA DEL ÄR
ÖPPNAD OCH SPÄRREN ÄR URKOPPLAD. BETRAKTA EJ STRÅLEN.
ADVERSEL
:
USYNLIG LASERSTRÅLING NÅR DEKSEL ÅPNES OG
SIKKERHEDSLÅS BRYTES. UNNGÅ EKSPONERING FOR STRÅLEN.
VIGYAZAT
!
:
A BURKOLAT NYITÁSAKOR LÁTHATATLAN
LÉZERSUGÁRVESZÉLY
!  KERÜLJE A BESUGÁRZÁST!
Page of 70
Display

Click on the first or last page to see other HCD-GRX5 / HCD-RX66 / MHC-GRX5 / MHC-RX66 service manuals if exist.