Read Sony HCD-GRX10AV / HCD-RX110AV / MHC-GRX10AV / MHC-RX110AV Service Manual online
– 16 –
Record Bias Adjustment (Deck B)
Procedure:
INTRODUCTION
When set to the test mode performed in
When set to the test mode performed in
Tape Speed Adjust-
ment
,
when the tape is rewound after recording, the “REC memory
mode” which rewinds only the recorded portion and playback is
set.
This “REC memory mode” is convenient for performing this ad-
justment. During recording, the input signal FUNCTION will auto-
matically switch to VIDEO.
(After recording, press the – 0 button without stopping will
return to the position where recording was started.)
set.
This “REC memory mode” is convenient for performing this ad-
justment. During recording, the input signal FUNCTION will auto-
matically switch to VIDEO.
(After recording, press the – 0 button without stopping will
return to the position where recording was started.)
1. Press FUNCTION button to select VIDEO. (This step is not
necessary if the above test mode has already been set.)
2. Insert a tape into deck B, press the r REC button, and then
press the ( button to start recording.
3. Mode: Record
5. Confirm playback the signal recorded in step 2 become adjust-
ment level as follows.
If these levels do not adjustment level, adjust the RV341 (L-CH)
and RV441 (R-CH) on the AUDIO board to repeat steps 3 and 4.
If these levels do not adjustment level, adjust the RV341 (L-CH)
and RV441 (R-CH) on the AUDIO board to repeat steps 3 and 4.
Adjustment level: The playback output of 10 kHz level difference
against 315 Hz reference should be ± 1.0 dB.
Adjustment Location: AUDIO board
Record Level Adjustment (Deck B)
Procedure:
INTRODUCTION
When set to the test mode performed in
When set to the test mode performed in
Tape Speed Adjust-
ment
, when the tape is rewound after recording, the “REC memory
mode” which rewinds only the recorded portion and playback is
set.
This “REC memory mode” is convenient for performing this
adjustment. During recording, the input signal FUNCTION will au-
tomatically switch to VIDEO.
(After recording, press the – 0 button without stopping will
return to the position where recording was started.)
set.
This “REC memory mode” is convenient for performing this
adjustment. During recording, the input signal FUNCTION will au-
tomatically switch to VIDEO.
(After recording, press the – 0 button without stopping will
return to the position where recording was started.)
1. Press FUNCTION button to select VIDEO. (This step is not
necessary if the above test mode has already been set.)
2. Insert a tape into deck B, press the r REC button, and then
press the ( button to start recording.
3. Mode: Record
4. Mode: Playback
5. Confirm playback the signal recorded in step 2 become adjust-
ment level as follows.
If these levels do not adjustment level, adjust the RV301 (L-CH)
and RV351 (R-CH) on the MAIN board to repeat steps 3 and 4.
If these levels do not adjustment level, adjust the RV301 (L-CH)
and RV351 (R-CH) on the MAIN board to repeat steps 3 and 4.
Adjustment level:
CN403 playback level: 47.2 to 53.0 mV (–24.3 to –23.3 dB)
CN403 playback level: 47.2 to 53.0 mV (–24.3 to –23.3 dB)
Adjustment Location: MAIN board
Adjustment Location:
[AUDIO BOARD] (Conductor Side)
4. Mode: Playback
AF OSC
VIDEO (AUDIO) IN
1) 315 Hz
2) 10 kHz
1) 315 Hz
2) 10 kHz
blank tape
CS-123
CS-123
set
attenuator
600
Ω
} 50 mV (–23.8 dB)
recorded
position
position
level meter
set
main board
CN301
Pin
CN301
Pin
1
(L-CH)
Pin
3
(R-CH)
AF OSC
VIDEO (AUDIO) IN
315Hz 50 mV (–23.8 dB)
315Hz 50 mV (–23.8 dB)
blank tape
CS-123
CS-123
set
attenuator
600
Ω
recorded
position
position
level meter
set
main board
CN301
Pin
CN301
Pin
1
(L-CH)
Pin
3
(R-CH)
RV301
Record Level (Lch)
Record Level (Lch)
RV351
Record Level (Rch)
Record Level (Rch)
IC301
CN301
1 3
[MAIN BOARD] (Conductor Side)
RV441 RV341
RV301(Lch),RV401(Rch)
Playback Level (Deck B)
Playback Level (Deck B)
RV301 RV401
RV341(Lch),RV441(Rch)
Record Bias
Record Bias
RV311(Lch),RV411(Rch)
Playback Level (Deck A)
Playback Level (Deck A)
RV311
RV411
Click on the first or last page to see other HCD-GRX10AV / HCD-RX110AV / MHC-GRX10AV / MHC-RX110AV service manuals if exist.