Read Sony HCD-GR5 / HCD-RX50 / MHC-GR5 / MHC-RX50 Service Manual online
— 5 —
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused on
the disc reflective surface by the objective lens in the optical pick-
up block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.
the disc reflective surface by the objective lens in the optical pick-
up block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.
LASER DIODE AND FOCUS SEARCH OPERATION
CHECK
CHECK
Carry out the “S curve check” in “CD section adjustment” and check
that the S curve waveform is output two times.
that the S curve waveform is output two times.
Note for installation (ROTARY ENCODER)
[FL Display Tube, LED All Lit and Key Check mode]
When the TUNER/BAND , DISPLAY , and MENU 2 buttons
are pressed simultaneously, the FL display tube and LEDs will all
light up. Press any button to enter the key check mode.
When the key check mode is entered, the FL display tube displays
“K 1 J0 V0”. Each time a button is pressed, the counter increases
in the following order, K 2
are pressed simultaneously, the FL display tube and LEDs will all
light up. Press any button to enter the key check mode.
When the key check mode is entered, the FL display tube displays
“K 1 J0 V0”. Each time a button is pressed, the counter increases
in the following order, K 2
n K 3 n K 4.
If buttons already pressed once are pressed again, the counter will
not increase. When the VOLUME knob is rotated in the + direction,
the count increases in the following order.
V1
not increase. When the VOLUME knob is rotated in the + direction,
the count increases in the following order.
V1
n V2 n V3.
When rotated in the–direction, it decreases in the following order.
V0
V0
n V9 n V8.
When the AMS dial is rotated in the clockwise direction, the count
increases in the following order.
J1
increases in the following order.
J1
n J2 n J3.
When rotated in the counterclockwise direction, it decreases in the
following order.
J0
following order.
J0
n J9 n J8.
To exit form the test mode, press the TUNER/BAND , DISPLAY
, MENU 2 buttons simultaneously again.
, MENU 2 buttons simultaneously again.
[Switching the channel step 9 KHz/10 KHz]
Press ENTER/NEXT button and POWER button simultaneously
to switch the AM channel step 9 KHz and 10 KHz. Be sure not to
change with carelessness.
to switch the AM channel step 9 KHz and 10 KHz. Be sure not to
change with carelessness.
NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK
OR BASE UNIT
OR BASE UNIT
The laser diode in the optical pick-up block may suffer electrostatic
break-down because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled with
care.
break-down because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled with
care.
HOW TO OPEN THE DISC TRAY WHEN POWER SWITCH
TURNS OFF
TURNS OFF
SECTION 1
SERVICING NOTE
Insert a tapering driver into the
aperture of the unit bottom, and turn
in the direction of arrow.
aperture of the unit bottom, and turn
in the direction of arrow.
*
To close the disc tray, turn the
driver in the reverse direction.
Note :
When attaching the BU
cam, engage the Rotary
encoder switch as shown in
the figure.
cam, engage the Rotary
encoder switch as shown in
the figure.
Note :
When attaching the Base unit, insert the
section A into the groove of BU cam.
section A into the groove of BU cam.
groove
BU cam
Section A
Click on the first or last page to see other HCD-GR5 / HCD-RX50 / MHC-GR5 / MHC-RX50 service manuals if exist.