Read Sony HCD-GN999D / MHC-GN999D / MHC-GN999DS Service Manual online
4
HCD-GN999D
SECTION 1
SERVICING NOTES
NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK
OR BASE UNIT
OR BASE UNIT
The laser diode in the optical pick-up block may suffer electrostatic
break-down because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled with
care.
break-down because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled with
care.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused on
the disc reflective surface by the objective lens in the optical pick-
up block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.
the disc reflective surface by the objective lens in the optical pick-
up block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.
LASER DIODE AND FOCUS SEARCH OPERATION
CHECK
CHECK
Carry out the “S curve check” in “CD section adjustment” and check
that the S curve waveform is output several times.
that the S curve waveform is output several times.
• MODEL IDENTIFICATION
– Back Panel –
– Back Panel –
MODEL
PART No.
E3, E15 models
2-658-971-0
[]
E2 model
2-658-971-1
[]
EA model
2-658-971-2
[]
MY,SP models
2-658-971-3
[]
E12 model
2-658-971-4
[]
E13 model
2-658-971-5
[]
PH model
2-658-971-6
[]
MX model
2-658-971-7
[]
E51 model
2-658-971-8
[]
TH model
2-658-971-9
[]
Notes on chip component replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be
• Notice that the minus side of a tantalum capacitor may be
damaged by heat.
Flexible Circuit Board Repairing
• Keep the temperature of soldering iron around 270˚C
during repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous
radiation exposure.
other than those specified herein may result in hazardous
radiation exposure.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK
0
OR DOTTED LINE WITH
MARK
0
ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS
LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.
PART No.
•
Abbreviation
E2 : 120V AC Area in E model
E3 : 240V AC Area in E model
E12 : 220V-240V AC Area in E model
E13 : 220V-230V AC area in E model
E15 : Iran model
E51 : Chilean and Perurian model
EA : Saudi Arabia model
MX : Mexican model
MY : Malaysia model
PH : Philippines model
SP : Singapore model
TH : Thai model
E2 : 120V AC Area in E model
E3 : 240V AC Area in E model
E12 : 220V-240V AC Area in E model
E13 : 220V-230V AC area in E model
E15 : Iran model
E51 : Chilean and Perurian model
EA : Saudi Arabia model
MX : Mexican model
MY : Malaysia model
PH : Philippines model
SP : Singapore model
TH : Thai model
This appliance is classified as
a CLASS 1 LASER product.
This label is located on the rear
exterior.
a CLASS 1 LASER product.
This label is located on the rear
exterior.
NOTE ON REPLACEMENT OF DMB15 BOARD
New part of EEPROM (IC103) on the DMB15 board cannot be
used. Therefore, if the mounted DMB15 board (A-1167-802-A or
A-1167-915-A or A-1188-872-A) is replaced, exchange new
EEPROM with that used before the replacement.
used. Therefore, if the mounted DMB15 board (A-1167-802-A or
A-1167-915-A or A-1188-872-A) is replaced, exchange new
EEPROM with that used before the replacement.
CHANGE OF THE COMBINED BOARD SUFFIX
Suffix of the Main, Panel, Power and SMASTER combined board
was changed from -12 to -13.
was changed from -12 to -13.
Ver. 1.2
Click on the first or last page to see other HCD-GN999D / MHC-GN999D / MHC-GN999DS service manuals if exist.