Read Sony HCD-DR3 / HCD-DR330 / HCD-XB200 / LBT-DR3 / LBT-DR330 / LBT-XB200 Service Manual online
2
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK
!
OR DOTTED LINE WITH
MARK
!
ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS
LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.
This appliance is classified as a CLASS 1 LASER product. The
CLASS 1 LASER PRODUCT MARKING is located on the rear
exterior.
CLASS 1 LASER PRODUCT MARKING is located on the rear
exterior.
The following caution label is located inside the unit.
Laser component in this product is capable
of emitting radiation exceeding the limit for
Class 1.
of emitting radiation exceeding the limit for
Class 1.
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous radiation
exposure.
other than those specified herein may result in hazardous radiation
exposure.
Notes on chip component replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be
• Notice that the minus side of a tantalum capacitor may be
damaged by heat.
Flexible Circuit Board Repairing
• Keep the temperature of soldering iron around 270˚C
during repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.
AM tuner section
Tuning renge
European and Middle Eastern models:
531 – 1,602 kHz
(with the tuning interval set at 9 kHz)
(with the tuning interval set at 9 kHz)
Other models:
531 – 1,602 kHz
(with the tuning interval set at 9 kHz)
530 – 1,710 kHz
(with the tuning interval set at 10 kHz)
(with the tuning interval set at 9 kHz)
530 – 1,710 kHz
(with the tuning interval set at 10 kHz)
Antenna
AM loop antenna,
External antenna terminals
External antenna terminals
Intermediate frequency
450 kHz
General
Power requirements
European model:
230 V AC, 50/60 Hz
Mexican model:
120V AC, 50/60 Hz
Australian model:
220 – 240 V AC, 50/60 Hz
Other models:
110 – 120 V or 220 – 240 V AC, 50/60 Hz Adjustable
with voltage selector
with voltage selector
Power consumption
(HCD-DR330/DR3)
(HCD-DR330/DR3)
180W
(HCD-XB200)
135W
Dimensions(w/h/d)
Approx. 355
×
425
×
442 mm
(14
×
16
3
/
4
×
17
1
/
2
in) incl.
projecting parts and controls
Mass
Approx. 13.1 kg (28 lb 14 oz.)
Supplied accessories
AM loop antenna (1)
Remote RM-SG7B (1)
FM wire antenna (1)
Remote RM-SG7B (1)
FM wire antenna (1)
Design and specifications are subject to change without notice
Parts No.
PARTS No.
MODEL
4-222-140-0
π
XB200 : AEP, UK
4-222-141-0
π
XB200 : EE, CIS
4-222-142-0
π
DR3 : E, SP, AR
4-222-143-0
π
DR3 : AUS
4-222-144-0
π
DR3 : MX
4-222-145-0
π
DR330
MODEL IDENTIFICATION
• Abbreviation
SP
: Singapore model
MX : Mexican model
AR
AR
: Argentina model
AUS : Australian model
EE
EE
: East European model
Click on the first or last page to see other HCD-DR3 / HCD-DR330 / HCD-XB200 / LBT-DR3 / LBT-DR330 / LBT-XB200 service manuals if exist.