Read Sony HCD-DP900D Service Manual online
9
HCD-DP900D
On this screen, the mirror time is measured to judge the disc and it
is written to the EEPROM. First load DVD SL disc and press
is written to the EEPROM. First load DVD SL disc and press
[1]
,
next load CD disc and press
[2]
, and finally load DVD DL disc
and press
[3]
.
The adjustment must be executed more than once after default
data were written. External vibration or shock to the player must
not be given. Reference value for DVD is from 10 to 20, and for
CD, from 28 to 4F.
Check that the value of CD is larger than that of DVD.
When those values are beyond a range perform this adjustment
again.
From this screen, you can go to another mode by pressing
data were written. External vibration or shock to the player must
not be given. Reference value for DVD is from 10 to 20, and for
CD, from 28 to 4F.
Check that the value of CD is larger than that of DVD.
When those values are beyond a range perform this adjustment
again.
From this screen, you can go to another mode by pressing
[NEXT]
or
[PREV]
key, but you cannot enter this mode from another mode.
You can enter this mode from the Operation Menu screen only.
1.
Disc Type
Disc Type
1. Disc Type Auto Check
2. DVD SL
2. DVD SL
12 cm
3. DVD DL
12 cm
4. CD
12cm
5. SACD
12 cm
6. dvd SL
8 cm
7. DVD DL
8 cm
8. CD
8 cm
9. SACD
8 cm
0. Reset SLED TILT
EMG. 00
On this screen, select the disc type. To select the disc type, press
the number of the loaded disc. The selected disc type is displayed
at the bottom. Selecting
the number of the loaded disc. The selected disc type is displayed
at the bottom. Selecting
[1]
automatically selects and displays the
disc type. In case of wrong display, retry “Disc Check Memory”.
Also, opening the tray causes the set disc type to be cleared. In
this case, set the disc type again after loading.
In performing manual operation, the disc type must be set.
Once the disc type has been selected, the sector address or time
code display field will appear as shown below. These values are
displayed when PLL is locked.
Also, opening the tray causes the set disc type to be cleared. In
this case, set the disc type again after loading.
In performing manual operation, the disc type must be set.
Once the disc type has been selected, the sector address or time
code display field will appear as shown below. These values are
displayed when PLL is locked.
Disc Type
1. Disc Type Auto Check
2. DVD SL
2. DVD SL
12 cm
3. DVD DL
12 cm
4. CD
12cm
5. SACD
12 cm
6. dvd SL
8 cm
7. DVD DL
8 cm
8. CD
8 cm
9. SACD
8 cm
0. Reset SLED TILT
SA. SI. EMG. 00
DVD SL 12 cm
Display when DVD SL 12cm disc was selected
Disc Type
1. Disc Type Auto Check
2. DVD SL
2. DVD SL
12 cm
3. DVD DL
12 cm
4. CD
12cm
5. SACD
12 cm
6. dvd SL
8 cm
7. DVD DL
8 cm
8. CD
8 cm
9. SACD
8 cm
0. Reset SLED TILT
TC. : : EMG. 00
CD 12 cm
Display when CD 12cm disc was selected
[10/0]
Reset SLED TILT Reset the Sled and Tilt to initial posi-
tion.
[1]
Disk Type Check
Judge automatically the loaded disc. As
the judged result is displayed at the bot-
tom of screen, make sure that it is cor-
rect.
If Disc Check Memory Menu has not
been executed after EEPROM default
setting, the disc type cannot be judged.
In this case, return to the initial menu
and make a check for three types of
discs (SL, DL, CD).
the judged result is displayed at the bot-
tom of screen, make sure that it is cor-
rect.
If Disc Check Memory Menu has not
been executed after EEPROM default
setting, the disc type cannot be judged.
In this case, return to the initial menu
and make a check for three types of
discs (SL, DL, CD).
[2]
to
[9]
Select the loaded disc. The adjusted
value is written to the address of se-
lected disc. No further entry is neces-
sary if
value is written to the address of se-
lected disc. No further entry is neces-
sary if
[1]
was selected.
2. Servo Control
Servo Control
1. LD
Off R.Sled FWD
2. SP
Off L.Sled REV
3. Focus
Off
4. TRK.
Off
5. Sled
Off
6. CLVA
Off
7. FCS. Srch Off
0. Reset SLED TILT
SA. SI. EMG. 00
DVD SL 12 cm
On this screen, the servo on/off control necessary for replay is
executed. Normally, turn on each servo from 1 sequentially and
when CLVA is turned on, the usual trace mode becomes active. In
the trace mode, DVD sector address or CD time code is displayed.
This is not displayed where the spindle is not locked.
The spindle could run overriding the control if the spindle system
is faulty or RF is not present. In such a case, do not operate CLVA.
executed. Normally, turn on each servo from 1 sequentially and
when CLVA is turned on, the usual trace mode becomes active. In
the trace mode, DVD sector address or CD time code is displayed.
This is not displayed where the spindle is not locked.
The spindle could run overriding the control if the spindle system
is faulty or RF is not present. In such a case, do not operate CLVA.
Click on the first or last page to see other HCD-DP900D service manuals if exist.