Read Sony HCD-D890AV / HCD-XB55AV / HCD-XB80AV / HCD-XB88AV / LBT-D890AV / LBT-XB55AV / LBT-XB80AV Service Manual online
– 14 –
Record Bias Adjustment (Deck B)
Procedure:
INTRODUCTION
When set to the test mode performed in
When set to the test mode performed in
Tape Speed Adjust-
ment
,
when the tape is rewound after recording, the “REC memory
mode” which rewinds only the recorded portion and playback is
set.
This “REC memory mode” is convenient for performing this ad-
justment. During recording, the input signal FUNCTION will auto-
matically switch to VIDEO.
set.
This “REC memory mode” is convenient for performing this ad-
justment. During recording, the input signal FUNCTION will auto-
matically switch to VIDEO.
1. Press FUNCTION button to select VIDEO. (This step is not
necessary if the above test mode has already been set.)
2. Load a tape into deck B, and press the r REC button.
3. Mode: Record
3. Mode: Record
4. Mode: Playback
5. Confirm playback the signal recorded in step 2 become adjust-
ment level as follows.
If these levels do not adjustment level, adjust the RV341 (L-CH)
and RV441 (R-CH) on the AUDIO board to repeat steps 3 and 4.
If these levels do not adjustment level, adjust the RV341 (L-CH)
and RV441 (R-CH) on the AUDIO board to repeat steps 3 and 4.
Adjustment level: The playback output of 10 kHz level difference
against 315 Hz reference should be ± 1.0 dB.
Adjustment Location: AUDIO board
Record Level Adjustment (Deck B)
Procedure:
INTRODUCTION
When set to the test mode performed in
When set to the test mode performed in
Tape Speed Adjust-
ment
, when the tape is rewound after recording, the “REC memory
mode” which rewinds only the recorded portion and playback is
set.
This “REC memory mode” is convenient for performing this
adjustment. During recording, the input signal FUNCTION will au-
tomatically switch to VIDEO.
set.
This “REC memory mode” is convenient for performing this
adjustment. During recording, the input signal FUNCTION will au-
tomatically switch to VIDEO.
1. Press FUNCTION button to select VIDEO. (This step is not
necessary if the above test mode has already been set.)
2. Load a tape into deck B, and press the r REC button.
3. Mode: Record
3. Mode: Record
4. Mode: Playback
5. Confirm playback the signal recorded in step 2 become adjust-
ment level as follows.
If these levels do not adjustment level, adjust the RV301 (L-CH)
and RV351 (R-CH) on the MAIN board to repeat steps 3 and 4.
If these levels do not adjustment level, adjust the RV301 (L-CH)
and RV351 (R-CH) on the MAIN board to repeat steps 3 and 4.
Adjustment level:
CN403 playback level: 47.2 to 53.0 mV (–24.3 to –23.3 dB)
CN403 playback level: 47.2 to 53.0 mV (–24.3 to –23.3 dB)
Adjustment Location: MAIN board
Adjustment Location
[AUDIO BOARD] (Conductor Side)
[AUDIO BOARD] (Conductor Side)
AF OSC
VIDEO/MD (AUDIO) IN
1) 315 Hz
2) 10 kHz
1) 315 Hz
2) 10 kHz
blank tape
CS-123
CS-123
set
attenuator
600
Ω
} 50 mV (–23.8 dB)
recorded
position
position
level meter
set
main board
CN403
CN403
Pin
3
(L-CH)
Pin
1
(R-CH)
recorded
position
position
level meter
set
main board
CN403
CN403
Pin
3
(L-CH)
Pin
1
(R-CH)
[MAIN BOARD] (Component Side)
CN403
IC401
1
3
RV351
Record Level
(R CH)
Record Level
(R CH)
RV301
Record Level (L CH)
Record Level (L CH)
RV341(Lch),RV441(Rch)
Record Bias
Record Bias
RV301
RV401
RV441 RV341
RV301(Lch),RV401(Rch)
Playback Level (Deck B)
Playback Level (Deck B)
RV651 (Normal Speed)
RV652 (High Speed)
Tape Speed
RV652 (High Speed)
Tape Speed
RV651
RV311(Lch),RV411(Rch)
Playback Level (Deck A)
Playback Level (Deck A)
RV652
RV311
RV411
AF OSC
VIDEO/MD (AUDIO) IN
1) 315 Hz
2) 10 kHz
1) 315 Hz
2) 10 kHz
blank tape
CS-123
CS-123
set
attenuator
600
Ω
} 50 mV (–23.8 dB)
Click on the first or last page to see other HCD-D890AV / HCD-XB55AV / HCD-XB80AV / HCD-XB88AV / LBT-D890AV / LBT-XB55AV / LBT-XB80AV service manuals if exist.