Read Sony HCD-D690 / HCD-XB6 / HCD-XB600 Service Manual online
– 1 –
HCD-D690/XB6/XB600
SERVICE MANUAL
US Model
Canadian Model
HCD-D690
AEP Model
UK Model
E Model
Australian Model
HCD-XB6
Mexican Model
HCD-XB600
CORRECTION-1
Please correct your service manual.
1. TEST MODE
2. ELECTRICAL ADJUSTMENTS
3. BLOCK DIAGRAMS (MAIN SECTION)
2. ELECTRICAL ADJUSTMENTS
3. BLOCK DIAGRAMS (MAIN SECTION)
•
This is to inform you the revision of previously distributed
service manual (9-960-880-11).
Regarding TEST MODE page30 and page31, please replace
them to the revised edition page2 and page3.
Regarding TEST MODE page30 and page31, please replace
them to the revised edition page2 and page3.
– 2 –
[MC Cold Reset]
•
The cold reset clears all data including preset data stored in the
RAM to initial conditions. Execute this mode when returning
the set to the customer.
RAM to initial conditions. Execute this mode when returning
the set to the customer.
Procedure:
1. Press three buttons SPECTRUM ANALYZER ,
1. Press three buttons SPECTRUM ANALYZER ,
ENTER
and DISC 1 simultaneously.
2. The fluorescent indicator tube becomes blank instantaneously,
and the set is reset.
[CD Delivery Mode]
•
This mode moves the pick-up to the position durable to vibra-
tion. Use this mode when returning the set to the customer after
repair.
tion. Use this mode when returning the set to the customer after
repair.
Procedure:
1. Press POWER button to turn the set ON.
2. Press PLAY MODE button and POWER button simulta-
1. Press POWER button to turn the set ON.
2. Press PLAY MODE button and POWER button simulta-
neously.
3. A message “LOCK” is displayed on the fluorescent indicator
tube, and the CD delivery mode is set.
[MC Hot Reset]
•
This mode resets the set with the preset data kept stored in the
memory. The hot reset mode functions same as if the power
cord is plugged in and out.
memory. The hot reset mode functions same as if the power
cord is plugged in and out.
Procedure:
1. Press three buttons SPECTRUM ANALYZER ,
1. Press three buttons SPECTRUM ANALYZER ,
ENTER
and DISC 2 simultaneously.
2. The fluorescent indicator tube becomes blank instantaneously,
and the set is reset.
[Sled Servo Mode]
•
This mode can run the CD sled motor freely. Use this mode, for
instance, when cleaning the pick-up.
instance, when cleaning the pick-up.
Procedure:
1. Select the function “CD”.
2. Press three buttons SPECTRUM ANALYZER ,
1. Select the function “CD”.
2. Press three buttons SPECTRUM ANALYZER ,
ENTER
and FUNCTION simultaneously.
3. The Sled Servo mode is selected, if “CD” is blanking on the
fluorescent indicator tube.
4. With the CD in stop status, press
) button in CD section
to move the pick-up to outside track, or
0 button to inside
track.
5. To exit from this mode, perform as follows:
1) Move the pickup to the most inside track.
2) Press three buttons in the same manner as step 2, or dis-
2) Press three buttons in the same manner as step 2, or dis-
connect the power cord.
Note:
•
Always move the pick-up to most inside track when exiting from
this mode. Otherwise, a disc will not be unloaded.
this mode. Otherwise, a disc will not be unloaded.
•
Do not run the sled motor excessively, otherwise the gear can
be chipped.
be chipped.
[Change-over of AM Tuner Step between 9kHz and 10kHz]
•
A step of AM channels can be changed over between 9kHz and
10kHz.
10kHz.
Procedure:
1. Press POWER button to turn the set ON.
2. Select the function “TUNER”, and press TUNER/BAND
1. Press POWER button to turn the set ON.
2. Select the function “TUNER”, and press TUNER/BAND
button to select the BAND “AM”.
3. Press POWER button to turn the set OFF.
4. Press ENTER/NEXT and POWER buttons simultaneously,
4. Press ENTER/NEXT and POWER buttons simultaneously,
and the display of fluorescent indicator tube changes to “AM
9k STEP” or “AM 10k STEP”, and thus the channel step is
changed over.
9k STEP” or “AM 10k STEP”, and thus the channel step is
changed over.
[LED and Fluorescent Indicator Tube All Lit, Key Check
Mode]
Mode]
Procedure:
1. Press three buttons SPECTRUM ANALYZER ,
1. Press three buttons SPECTRUM ANALYZER ,
ENTER
and DISC 3 simultaneously.
2. LEDs and fluorescent indicator tube are all turned on.
Press DISC 2 button, and the key check mode is activated.
3. In the key check mode, the fluorescent indicator tube displays
“K 1 V0 J0”. Each time a button is pressed, “K”value in-
creases. However, once a button is pressed, it is no longer taken
into account.
“J” Value increases like 1, 2, 3 ... if rotating JOG knob in “+”
direction, or it decreases like 0, 9, 8 ... if rotating in “–” direc-
tion.
“V” Value increases like 1, 2, 3 ... if rotating VOLUME knob
in “+” direction, or it decreases like 0, 9, 8 ... if rotating in “–
” direction.
creases. However, once a button is pressed, it is no longer taken
into account.
“J” Value increases like 1, 2, 3 ... if rotating JOG knob in “+”
direction, or it decreases like 0, 9, 8 ... if rotating in “–” direc-
tion.
“V” Value increases like 1, 2, 3 ... if rotating VOLUME knob
in “+” direction, or it decreases like 0, 9, 8 ... if rotating in “–
” direction.
4. To exit from this mode, press three buttons in the same man-
ner as step 1, or disconnect the power cord.
1. TEST MODE
– 3 –
[Aging Mode]
This mode can be used for operation check of CD section and tape
deck section.
deck section.
•
If an error occurred:
The aging operation stops.
•
If no error occurs:
The aging operation continues repeatedly.
1. Aging Mode in CD Section
1-1. Operating Method of Aging Mode
1-1. Operating Method of Aging Mode
1. Set discs in DISC 1 and DISC 3 trays.
2. Select the function “CD”.
3. Press three buttons SPECTRUM ANALYZER , ENTER
2. Select the function “CD”.
3. Press three buttons SPECTRUM ANALYZER , ENTER
and KARAOKE
PON/MPX simultaneously.
4. The aging mode is activated, if a roulette mark on the fluo-
rescent indicator tube is blinking.
5. In the aging mode, the aging is executed in a sequence
given in “1-2. Operation during Aging Mode”.
The aging continues unless an alarm occurred.
The aging continues unless an alarm occurred.
6. To exit from the aging mode, press POWER button to
turn the set OFF.
•
If a button other than buttons In CD section is pressed during
aging, the aging in the CD section is finished.
aging, the aging in the CD section is finished.
•
To execute aging to the tape deck section successively, press
·
button in the deck A.
“AGING” is displayed on the fluorescent indicator tube. (For
the aging in tape deck, see “2. Aging Mode in Tape Deck Sec-
tion”.
“AGING” is displayed on the fluorescent indicator tube. (For
the aging in tape deck, see “2. Aging Mode in Tape Deck Sec-
tion”.
1-2. Operation during aging Mode
In the aging mode, the program is executed in the following se-
quence.
In the aging mode, the program is executed in the following se-
quence.
1. The disc tray turns to select a disc. (For a disc selection
sequence, see Section 1-3.)
2. TOC of disc is read.
3. The pick-up accesses to the last track.
4. Steps 1 through 3 are repeated.
3. The pick-up accesses to the last track.
4. Steps 1 through 3 are repeated.
1-3. Disc Selection Sequence
•
During the aging mode, discs are selected in the following se-
quence:
quence:
Disc 1
→
Disc 3
↑
↓
Disc 3
←
Disc 1
2. Aging Mode in Tape Deck Section
2-1. Operating Method of Aging Mode
2-1. Operating Method of Aging Mode
1. Load a commercially available 10-minute tape into the
decks A and B respectively.
(If a 10-minute tape is not available, another tape may be
used but a cycle time will be longer.)
(If a 10-minute tape is not available, another tape may be
used but a cycle time will be longer.)
2. Select the function “TAPE”.
3. Rewind tapes in advance by pressing
3. Rewind tapes in advance by pressing
0 button respec-
tively on decks A and B.
4. Press three buttons SPECTRUM ANALYZER , ENTER
and KARAOKE
PON/MPX simultaneously.
5. Press
· button on deck A. (This button triggers the ag-
ing mode.)
6. The aging mode is activated if “AGING A” is displayed
on the fluorescent indicator tube.
7. In the aging mode, the aging is executed in a sequence
given in “2-2. Operation during Aging Mode”.
The aging continues unless an alarm occurred.
The aging continues unless an alarm occurred.
8. To exit from the aging mode, press POWER button to turn
the set OFF.
2-2. Operation during Aging Mode
In the aging mode, the program is executed in the following se-
quence.
In the aging mode, the program is executed in the following se-
quence.
1. A tape on FWD side is played for one minute.
2. PAUSE STOP is made.
3. Recording is made for 3 minutes. (For the deck not having
2. PAUSE STOP is made.
3. Recording is made for 3 minutes. (For the deck not having
the record function, the play is executed.)
4. FF is executed up to the end of tape.
5. A tape is reversed, and the tape on REV side is played for
5. A tape is reversed, and the tape on REV side is played for
one minute.
6. PAUSE STOP is made.
7. Recording is made for 3 minutes. (For the deck not hav-
7. Recording is made for 3 minutes. (For the deck not hav-
ing the record function, the play is executed.)
8. FF is executed up to the end of tape.
9. Steps 1 through 8 are executed for the other deck.
10. Steps 1 through 9 are repeated unless an alarm occurred.
9. Steps 1 through 8 are executed for the other deck.
10. Steps 1 through 9 are repeated unless an alarm occurred.
2-3. Deck Selection Sequence
•
During the aging mode, decks are selected in the following se-
quence:
quence:
Deck A (FWD)
→
Deck A (REV)
↑
↓
Deck B (REV)
←
Deck B (FWD)
– 4 –
correct
8. Set to test mode. (Press key switch same time SPEC-
TRUM ANALYZER ENTER and EFFECT button.)
Tape Speed Adjustment
DECK A
Procedure:
2. Press the SPECTRUM ANALYZER button, ENTER button
2. Press the SPECTRUM ANALYZER button, ENTER button
and EFFECT button simultaneously.
CD SECTION
Note:
Sony Corporation
Home A&V Products Company
9-960-880-91
97D0594-1
Printed in Japan © 1997. 4
Published by General Engineering Dept.
(Shibaura)
HCD-D690/XB6/XB600
2. ELECTRICAL ADJUSTMENTS
Page
32
33
37
incorrect
8. Set to test mode. (Press key switch same time
GROOVE
ENTER/NEXT
and
DISC 4
button.)
Tape Speed Adjustment
DECK A
Procedure:
2. Press the GROOVE button, ENTER/NEXT button and
2. Press the GROOVE button, ENTER/NEXT button and
DISC 4 button simultaneously.
CD SECTION
Note:
5. Adjust the focus bias adjustment when optical block is re-
5. Adjust the focus bias adjustment when optical block is re-
placed.
D611-D625
D631,D632
D635-D638
D631,D632
D635-D638
D641
D645-D647
LED DRIVE
Q604-Q608
Q609-Q611
Q609-Q611
Q614
Q617-Q619
Q621
SELECT SWITCH
Q601-Q603
S601-S626,S628-S631
S641-S647,S651-S659
S661-S668,S676-S679
S641-S647,S651-S659
S661-S668,S676-S679
JOG
S711
VOLUME
ROTARY
ENCODER
S701
IC602
SIRCS
MID FREQ
LOW FREQ
HIGH FREQ
FL601
FRUORESCENT INDICATOR TUBE
25
23
24
8
9
32
36 37
33
10
34
20
21
42- 56
57- 77
22 • 35
27 - 30
79-80 • 1-6 • 14-19
LED SELECT
CLOCK
DATA
DATA
GR1-GR15
SEG1-SEG20
X OUT
X IN
L+R
SPEANA1
SPEANA2
SIRCS
RESET
DOOR SW
KEY1-KEY4
JOG A•B
LED
IC601
DISPLAY CONTROL
S691
DOOR SW
X601
8MHz
VF
VF
3. BLOCK DIAGRAMS – MAIN SECTION –
Page
47-48
incorrect
correct
D611-D625
D631,D632
D635-D638
D631,D632
D635-D638
D641
D645-D647
LED DRIVE
Q604-Q608
Q609-Q611
Q614,Q615
Q617-Q619
Q621,Q622
Q609-Q611
Q614,Q615
Q617-Q619
Q621,Q622
SELECT SWITCH
Q601-Q603
S601-S607,S609-S616
S619-S625,S627-S634
S641-S647,S651-S659
S661-S668,S676-S679
S619-S625,S627-S634
S641-S647,S651-S659
S661-S668,S676-S679
S681-S686
JOG
S711
VOLUME
OPEN
AMS
ROTARY
ENCODER
S701
IC602
SIRCS
F1
F2
F3
F4
FL601
FRUORESCENT INDICATOR TUBE
29
27
28
12
13
45 44 43 42
39
14
40
24
38
51-66
67-100
•
1
26 • 41
33 - 37
3-10
•
15
•
16
•
18-23
•
25
•
47
LED SELECT
CLOCK
DATA
DATA
GR1-GR16
SEG1-SEG35
X OUT
2
V-LOAD
X IN
SPEANA3
SPEANA4
SPEANA2
SPEANA1
SIRCS
RESET
DOOR SW
VOL-A
VOL-B
KEY1-KEY5
JOG A•B
LED
IC601
DISPLAY CONTROL
S691
DOOR SW
X601
8MHz
LOW FREQ
HIGH FREQ
VF
VF
VP
§
: Corrected Portion
: Corrected Portion
