Read Sony HCD-BX20I / HCD-BX50BTI Service Manual online
HCD-BX20i/BX50BTi
4
NOTES ON HANDLING THE OPTICAL PICK-UP
BLOCK OR BASE UNIT
BLOCK OR BASE UNIT
The laser diode in the optical pick-up block may suffer electro-
static break-down because of the potential difference generated by
the charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The fl exible board is easily damaged and should be handled with
care.
static break-down because of the potential difference generated by
the charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The fl exible board is easily damaged and should be handled with
care.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused
on the disc refl ective surface by the objective lens in the optical
pickup block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.
The laser beam on this model is concentrated so as to be focused
on the disc refl ective surface by the objective lens in the optical
pickup block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40 °C higher
• Unleaded solder melts at a temperature about 40 °C higher
than ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350 °C.
Caution: The printed pattern (copper foil) may peel away if the
about 350 °C.
Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!
• Strong
viscosity
Unleaded solder is more viscous (sticky, less prone to fl ow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
also be added to ordinary solder.
SECTION 1
SERVICING NOTES
ANTITHEFT UNLOCK MODE
Procedure:
1. Press the [
Procedure:
1. Press the [
?/1
] button to turn the power on.
2. Press the [FUNCTION] button to select “CD”.
3. Press two buttons of [
3. Press two buttons of [
x/
CANCEL] and [
A
] for 5 seconds.
4. The message “UNLOCKED” is displayed on the fl uorescent
indicator tube and the disc tray is unlocked.
Note: When “LOCKED” is displayed, the tray lock is not released by
turning power on/off with the [
?/1] button.
NOTE OF REPLACING THE IC904 ON THE BT BOARD
IC904 on the BT board cannot exchange with single. When IC904
on the BT board is damaged, exchange the entire mounted board.
IC904 on the BT board cannot exchange with single. When IC904
on the BT board is damaged, exchange the entire mounted board.
Model
Part No.
HCD-BX20i: US model
3-293-462-0
[]
HCD-BX20i: Canadian model
3-293-463-0
[]
HCD-BX50BTi: US model
3-293-464-0
[]
HCD-BX50BTi: Canadian model
3-293-465-0
[]
HCD-BX20i: Australian model
3-295-838-0
[]
HCD-BX20i: Singapore model
3-296-979-0
[]
HCD-BX20i: AEP model
4-154-084-0
[]
MODEL IDENTIFICATION
Part No.
– Rear View – (Except Singapore model)
Ver. 1.4
– Bottom View – (Singapore model)
Part No.
Click on the first or last page to see other HCD-BX20I / HCD-BX50BTI service manuals if exist.