Read Sony DXA-WZ8D / MHC-WZ8D Service Manual online
2
DXA-WZ8D
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK
0
OR DOTTED LINE WITH
MARK
0
ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS
LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.
Notes on chip component replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be
• Notice that the minus side of a tantalum capacitor may be
damaged by heat.
Flexible Circuit Board Repairing
• Keep the temperature of soldering iron around 270˚C
during repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.
TABLE OF CONTENTS
1. GENERAL
·········································································· 3
2. DISASSEMBLY
························································· 5
2-1. Case ··············································································· 5
2-2. Switching Power, DC Fan and Back Panel ··················· 6
2-3. TC MAIN Board ··························································· 6
2-4. FRONT AMP Board and SURROUND AMP Board ···· 7
2-5. Front Panel Assy ···························································· 7
2-6. Tape Mechanism Deck (CWM43RR23) ······················· 8
2-7. Lid (TC) Assy, Holder (A) Assy and Holder (B) Assy ·· 8
2-2. Switching Power, DC Fan and Back Panel ··················· 6
2-3. TC MAIN Board ··························································· 6
2-4. FRONT AMP Board and SURROUND AMP Board ···· 7
2-5. Front Panel Assy ···························································· 7
2-6. Tape Mechanism Deck (CWM43RR23) ······················· 8
2-7. Lid (TC) Assy, Holder (A) Assy and Holder (B) Assy ·· 8
3. ELECTRICAL ADJUSTMENTS
································· 9
4. DIAGRAMS
······································································ 10
4-1. Block Diagram ···························································· 11
4-2. Printed Wiring Board – TC MAIN Board – ··············· 12
4-3. Schematic Diagram
4-2. Printed Wiring Board – TC MAIN Board – ··············· 12
4-3. Schematic Diagram
– TC MAIN Board (1/2) – ······ 13
– TC MAIN Board (2/2) – ······ 14
– TC MAIN Board (2/2) – ······ 14
4-4. Printed Wiring Board – FRONT AMP Board – ········· 15
4-5. Schematic Diagram
4-5. Schematic Diagram
– FRONT AMP Board – ········· 16
4-6. Printed Wiring Board – SURROUND AMP Board – 15
4-7. Schematic Diagram
4-7. Schematic Diagram
– SURROUND AMP Board – 16
5. EXPLODED VIEWS
5-1. Front Panel Section ····················································· 17
5-2. Chassis Section ···························································· 18
5-3. Tape Mechanism Deck Section ··································· 19
5-2. Chassis Section ···························································· 18
5-3. Tape Mechanism Deck Section ··································· 19
6. ELECTRICAL PARTS LIST
······································· 20
Unleaded solder
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size.)
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size.)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40
• Unleaded solder melts at a temperature about 40
°C higher than
ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350
°C.
Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!
heated tip is applied for too long, so be careful!
• Strong viscosity
Unleaded solder is more viscous (sticky, less prone to flow) than
ordinary solder so use caution not to let solder bridges occur such
as on IC pins, etc.
ordinary solder so use caution not to let solder bridges occur such
as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
also be added to ordinary solder.
[When bringing in the equipment for service]
In case of repairing, please bring the entire system set([HCD-WZ5,
DXA-WZ5],except for the speaker) to the service station.
DXA-WZ5],except for the speaker) to the service station.
Other models:
120 V, 220 V or
230 – 240 V AC, 50/60 Hz
Adjustable with voltage
selector
230 – 240 V AC, 50/60 Hz
Adjustable with voltage
selector
Power consumption
European and Russian models:
European and Russian models:
235 watts
0.3 watts (in Power Saving
Mode)
0.3 watts (in Power Saving
Mode)
Other models:
260 watts
Dimensions (w/h/d)
Amplifier/Tape deck:
Amplifier/Tape deck:
Approx. 255
× 135 ×
330 mm
Mass
Amplifier/Tape deck:
Amplifier/Tape deck:
Approx. 8.5 kg
Supplied accessories:
Remote Commander (1)
Batteries (2)
AM loop antenna (1)
FM lead antenna (1)
Speaker pads (20)
Speaker cords (5)
Video cord (1)
Batteries (2)
AM loop antenna (1)
FM lead antenna (1)
Speaker pads (20)
Speaker cords (5)
Video cord (1)
Design and specifications are subject to change
without notice.
without notice.
MODEL IDENTIFICATION
— BACK PANEL —
• Abbreviation
AUS
: Australian model
E2
: 120V AC area in E model
E3
: 240V AC area in E model
E15
: 220-240V AC area in E model
EA
: Saudi Arabia model
KR
: Korean model
PARTS No.
VOLTAGE SELECTOR Switch
MY
: Malaysia model
PH
: Philippines model
RU
: Russian model
SP
: Singapore model
TH
: Thai model
MODEL
AEP, UK models
EA model
E2,E3,E15 models
AUS model
TH model
PARTS No.
4-244-898-0
s
4-244-898-1
s
4-244-898-2
s
4-244-898-4
s
4-244-898-6
s
MODEL
KR model
MY,SP models
RU model
PH model
PARTS No.
4-244-898-7
s
4-244-898-8
s
4-244-898-9
s
4-247-937-0
s
Click on the first or last page to see other DXA-WZ8D / MHC-WZ8D service manuals if exist.