Read Sony DXA-WZ88D / MHC-WZ88D Service Manual online
2
DXA-WZ88D
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40 °C higher
than ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350
°C.
Caution: The printed pattern (copper foil) may peel away if
the heated tip is applied for too long, so be careful!
• Strong viscosity
Unleaded solder is more viscou-s (sticky, less prone to flow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
also be added to ordinary solder.
Notes on chip component replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be
damaged by heat.
Flexible Circuit Board Repairing
• Keep the temperature of the soldering iron around 270 °C
during repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK
0
OR DOTTED LINE
WITH MARK
0
ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE
PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR
IN SUPPLEMENTS PUBLISHED BY SONY.
REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE
PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR
IN SUPPLEMENTS PUBLISHED BY SONY.
TABLE OF CONTENTS
1.
GENERAL
...................................................................
3
2.
DISASSEMBLY
2-1.
Disassembly Flow ...........................................................
5
2-2.
Case .................................................................................
6
2-3.
Switching Power, DC Fan, Back Panel ...........................
7
2-4.
TC MAIN Board .............................................................
7
2-5.
FRONT AMP Board, SURROUND AMP Board ............
8
2-6.
Front Panel Section .........................................................
8
2-7.
Tape Mechanism Deck (CWM43RR602) .......................
9
2-8.
TC Holder (A), TC Holder (B), Lid (TC) Assy ............... 10
3.
ELECTRICAL ADJUSTMENTS
.......................... 11
4.
DIAGRAMS
4-1.
Block Diagram ................................................................ 13
4-2.
Printed Wiring Board – TC MAIN Section – ................. 14
4-3.
Schematic Diagram – TC MAIN Section (1/2) – ........... 15
4-4.
Schematic Diagram – TC MAIN Section (2/2) – ........... 16
4-5.
Printed Wiring Board – FRONT AMP Section – ........... 17
4-6.
Schematic Diagram – FRONT AMP Section – .............. 18
4-7.
Printed Wiring Board – SURROUND AMP Section – ... 19
4-8.
Schematic Diagram – SURROUND AMP Section – ...... 20
5.
EXPLODED VIEWS
5-1.
Front Panel Section ......................................................... 21
5-2.
Chassis Section ................................................................ 22
5-3.
Tape Mechanism Deck Section (CWM43RR602) .......... 23
6.
ELECTRICAL PARTS LIST
.................................. 24
MODEL IDENTIFICATION
– Rear Panel –
– Rear Panel –
Model
Part No.
EXCEPT EA, AUS models
2-580-718-0
[]
EA, AUS models
2-580-718-1
[]
• Abbreviation
AUS
: Australian model
EA
: Saudi Arabia model
PARTS No.
VOLTAGE SELECTOR Switch
Note:
DXA-WZ88D does not operate independently.
HCD-WZ88D is required to operate this.
In this case of a service, please connect HCD-WZ88D.
HCD-WZ88D is required to operate this.
In this case of a service, please connect HCD-WZ88D.
Click on the first or last page to see other DXA-WZ88D / MHC-WZ88D service manuals if exist.