Read Sony DVP-NS355 / DVP-NS360 / DVP-NS507P / DVP-NS525P / DVP-NS575P / DVP-NS585P / HT-1900DP / HTP-1200 / HTP-2000 / HTP-3200 Service Manual online
Laser: Semiconductor laser
Signal format system: NTSC
Frequency response: DVD VIDEO (PCM
DVD VIDEO (PCM 48 kHz): 2 Hz to
22 kHz (±0.5 dB)/CD: 2 Hz to 20 kHz
(±0.5 dB)
Harmonic distortion: 0.003%
Dynamic range: DVD VIDEO: 103 dB/
(Jack name: Jack type/Output level/
Power requirements:
120 V AC, 60 Hz
110-240 V AC, 50/60 Hz
See page 5 for further information
Dimensions (approx.): 430
parts
See page 17
change without notice.
As an
product meets the
and bridges.
to the customer and recommend their replacement.
their replacement.
tomer.
leakage as described below.
WITH THE EYE TOO CLOSELY. IN CASE IT IS NECESSARY TO
CONFIRM LASER BEAM EMISSION, BE SURE TO OBSERVE
FROM A DISTANCE OF MORE THAN 25 cm FROM THE SURFACE
OF THE OBJECTIVE LENS ON THE OPTICAL PICK-UP BLOCK.
The use of optical instrument with this product will increase eye
hazard.
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous radiation
exposure.
REPLACE THESE COMPONENTS WITH SONY PARTS
WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS
MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
safety checks before releasing the set to the customer:
The AC leakage from any exposed metal part to earth ground and
from all exposed metal parts to any exposed metal part having a
return to chassis, must not exceed 0.5mA (500 microampers).
Leakage current can be measured by any one of three methods.
instruments.
is 0.75V, so analog meters must have an accurate low voltage
scale. The Simpson 250 and Sanwa SH-63Trd are examples of
a passive VOM that is suitable. Nearly all battery operated
digital multimeters that have a 2V AC range are suitable. (See
Fig. A)
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size.)
• Unleaded solder melts at a temperature about 40°C highter than
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350°C
Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!
ordinary solder so use caution not to let solder bridges occur such
as on IC pins, etc.
be added to ordinary solder.
SONT CRITIQUES POUR LA SÉCURITÉ DE
FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS
QUE PAR DES PIÈSES SONY DONT LES NUMÉROS SONT
DONNÉS DANS CE MANUEL OU DANS LES SUPPÉMENTS
PUBLIÉS PAR SONY.
Voltmeter
(0.75 V)
About this Manual .......................................................... 1-1
This Player Can Play the Following Discs ................... 1-1
Notes about the Discs .................................................. 1-1
Index to Parts and Controls ......................................... 1-1
Guide to the Control Menu Display .............................. 1-2
Step 1: Unpacking ......................................................... 1-3
Step 2: Inserting Batteries into the Remote ................. 1-3
Step 3: Connecting the Video Cords ............................ 1-3
Step 4: Connecting the Audio Cords ............................ 1-4
Step 5: Connecting the Power Cord ............................. 1-5
Step 6: Quick Setup ...................................................... 1-5
Resuming Playback from the Point Where You
Selecting “ORIGINAL” or “PLAY LIST” on a
Searching by Scene (PICTURE NAVIGATION) ......... 1-9
TV Virtual Surround Settings (TVS) ............................. 1-10
Displaying the Subtitles ................................................. 1-11
Adjusting the Playback Picture
Playing DATA CDs with MP3 Audio Tracks and
Selecting an effect for image files in the slideshow .... 1-13
Setting the Display or Sound Track Language
Custom Settings (CUSTOM SETUP) .......................... 1-16
Settings for the Sound (AUDIO SETUP) ..................... 1-16
Self-diagnosis Function (When letters/
Specifications ................................................................. 1-18
SCHEMATIC DIAGRAMS
Waveform ...................................................................... 4-4
•
(MV-044 BOARD IC201) .............................................. 5-1
8-1-2. Mechanism Deck Assembly .................................... 8-2
When handling IF-112 PWB avoid contact with the sharp metal
edge on the top side of Vacuum Fluorescent Display (ND401).