DVP-NC615, DVP-NC655P, HT-5500D - Sony Audio Service Manual (repair manual)

Model
DVP-NC615 DVP-NC655P HT-5500D
Pages
124
Size
15.29 MB
Type
PDF
Document
Service Manual
Brand
Device
Audio
File
dvp-nc615-dvp-nc655p-ht-5500d.pdf
Date

View Sony DVP-NC615 / DVP-NC655P / HT-5500D Service Manual online

CD/DVD PLAYER
SPECIFICATIONS
DVP-NC615/NC655P
RMT-D143A/D143E/D143P/D144A
US Model
DVP-NC615/NC655P
Canadian Model
AEP Model
UK Model
E Model
Australian Model
Singapore Model
PX Model
DVP-NC615
SERVICE MANUAL
System
Laser: Semiconductor laser
Signal format system: 
U.S./Canadian models: NTSC
Asian/Oceanian models: PAL/NTSC
UK/European models: PAL/(NTSC)
(See page 1-3 to switch.)
Audio characteristics
Frequency response: DVD VIDEO (PCM 
96 kHz): 2 Hz to 44 kHz (
±1.0 dB)/DVD 
VIDEO (PCM 48 kHz): 2 Hz to 22 kHz 
(
±0.5 dB)/CD:  2 Hz  to  20 kHz  (±0.5 dB)
Signal-to-noise ratio (S/N ratio): 115 dB 
(LINE OUT L/R (AUDIO) jacks only)
Harmonic distortion: 0.003 %
Dynamic range: DVD VIDEO: 103 dB/CD: 
99 dB
Wow and flutter: Less than detected value 
(
±0.001% W PEAK)
The signals from LINE OUT L/R (AUDIO) 
jacks are measured. When you play PCM 
sound tracks with a 96 kHz sampling 
frequency, the output signals from the 
DIGITAL OUT (COAXIAL) jack are 
converted to 48 kHz sampling frequency.
Outputs
(Jack name: Jack type/Output level/Load 
impedance)
LINE OUT L/R (AUDIO): Phono jack/
2 Vrms/10 kilohms
DIGITAL OUT (COAXIAL): Phono jack/
0.5 Vp-p/75 ohms
COMPONENT VIDEO OUT(Y, P
B
/C
B
, P
R
/
C
R
): Phono jack/Y: 1.0 Vp-p/P
B
, P
R
,
 
C
B
C
R
,: 0.7 Vp-p/75 ohms (US/Canadian/
Asian/Oceanian models)
LINE OUT (VIDEO): Phono jack/1.0 Vp-p/
75 ohms
S VIDEO OUT: 4-pin mini DIN/
Y: 1.0 Vp-p/C:0.3 Vp-p (PAL), 
0.286 Vp-p (NTSC)/75 ohms
General
Power requirements: 
120 V AC, 60 Hz
110 to 240V AC, 50/60 Hz
220 to 240V AC, 50/60 Hz
See page 1-1 for further information.
Power consumption: 13 W/14 W
See page 1-1 for further information.
Mass (approx.): 5.1 kg (11 lb 4 oz)
Operating temperature: 5
° C to 35 ° C 
(41
°
F to 95
°
F)
Operating humidity: 25 % to 80 %
Supplied accessories
See page 1-3.
Specifications and design are subject to 
change without notice.
E
NERGY 
S
TAR
R
 is a U.S. registered mark. 
As an 
E
NERGY 
S
TAR
R
 Partner, Sony 
Corporation has determined that this product 
meets the 
E
NERGY 
S
TAR
R
 guidelines for 
energy efficiency.
DIGITAL OUT (OPTICAL): Optical 
output jack/–18 dBm (wave length 
660 nm) (UK/European models)
Dimensions (approx.): 430 
×  108 ×  409 mm 
430 
×  108 ×  411 mm 
(1
(NC615: UK, European models)
×  4 
3
/
8
 
×  16 
1
/
8
 in.):(NC615: US,
(17 
×  4 
3
/
8
 
×  16 
3
/
8
 in.): 
430 
×  108 ×  413 mm 
(NC655P model)
(17 
×  4 
3
/
8
 
×  16 
1
/
4
 in.): 
(width/height/depth)
 incl. projecting parts
Canadian, Asian, Oceanian models)
Photo : DVP-NC655P (SILVER)
RMT-D144A
— 2 —
SAFETY CHECK-OUT
After correcting the original service problem, perform the following
safety checks before releasing the set to the customer.
1.
Check the area of your repair for unsoldered or poorly-soldered
connections. Check the entire board surface for solder splashes
and bridges.
2.
Check the interboard wiring to ensure that no wires are
"pinched" or contact high-wattage resistors.
3.
Look for unauthorized replacement parts, particularly
transistors, that were installed during a previous repair. Point
them out to the customer and recommend their replacement.
4.
Look for parts which, though functioning, show obvious signs
of deterioration. Point them out to the customer and
recommend their replacement.
5.
Check the line cord for cracks and abrasion.
Recommend the replacement of any such line cord to the
customer.
6.
Check the B+ voltage to see it is at the values specified.
7.
Check the antenna terminals, metal trim, "metallized" knobs,
screws, and all other exposed metal parts for AC leakage.
Check leakage as described below.
LEAKAGE TEST
The AC leakage from any exposed metal part to earth ground and
from all exposed metal parts to any exposed metal part having a
return to chassis, must not exceed 0.5mA (500 microampers).
Leakage current can be measured by any one of three methods.
1.
A commercial leakage tester, such as the Simpson 229 or RCA
TW-540A. Follow the manufacturers' instructions to use these
instruments.
2.
A battery-operated AC milliammeter. The Data Precision 245
digital multimeter is suitable for this job.
3.
Measuring the voltage drop across a resistor by means of a
VOM or battery-operated AC voltmeter. The "limit" indication
is 0.75V, so analog meters must have an accurate low voltage
scale. The Simpson 250 and Sanwa SH-63Trd are examples
of a passive VOM that is suitable. Nearly all battery operated
digital multimeters that have a 2V AC range are suitable. (See
Fig. A)
Unleaded solder
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size.)
 : LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40°C higher than
ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350°C.
Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!
• Strong viscosity
Unleaded solder is more viscous (sticky, less prone to flow) than
ordinary solder so use caution not to let solder bridges occur such
as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH
MARK 
0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS
LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE 0 SUR LES
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE
REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY
DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU
DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
To Exposed Metal 
Parts on Set
0.15 
µF
1.5 k
AC
Voltmeter
(0.75 V)
Earth Ground
Fig. A.  Using an AC voltmeter to check AC leakage.
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous radiation
exposure.
WARNING!!
WHEN SERVICING, DO NOT APPROACH THE LASER EXIT WITH
THE EYE TOO CLOSELY. IN CASE IT IS NECESSARY TO
CONFIRM LASER BEAM EMISSION, BE SURE TO OBSERVE
FROM A DISTANCE OF MORE THAN 25 cm FROM THE SURFACE
OF THE OBJECTIVE LENS ON THE OPTICAL PICK-UP BLOCK.
CAUTION:
The use of optical instrument with this product will increase eye
hazard.
— 3 —
TABLE OF CONTENTS
SERVICE NOTE
1.
NOTE ON REMOVING THE UPPER CASE ··················· 5
2.
DISC REMOVAL PROCEDURE ······································ 5
3.
NOTE ON REMOVING THE TABLE ASS’Y ·················· 5
4.
NOTE ON MOUNTING THE GEARS ····························· 6
5.
HOW TO SERVICE THE MB-103 BOARD ····················· 7
6.
CONNECTION OF SERVICE JIG ···································· 9
1.
GENERAL
Precautions ············································································· 1-1
About this Manual ································································· 1-1
This Player Can Play the Following Discs ···························· 1-1
Notes about the Discs ···························································· 1-1
Index to Parts and Controls ···················································· 1-2
Guide to On-Screen Displays (Control Bar) ·························· 1-3
Simple Start Guide ···································································· 1-3
Quick Overview ····································································· 1-3
Step 1: Unpacking ································································· 1-3
Step 2: Inserting Batteries into the Remote ··························· 1-3
Step 3: TV Hookups ······························································ 1-3
Step 4: Playing a Disc ···························································· 1-4
Hookups ····················································································· 1-4
Hooking Up the Player ·························································· 1-4
Step 1: Connecting the Video Cords ······································ 1-4
Step 2: Connecting the Audio Cords ····································· 1-4
Step 3: Connecting the Power Cord ······································· 1-6
Step 4: Quick Setup ······························································· 1-6
Playing Discs ············································································· 1-6
Playing Discs ········································································· 1-6
Searching for a Particular Point on a Disc (Scan, Slow-motion
   Play, Search, Freeze Frame) ··············································· 1-7
Resuming Playback from the Point Where You Stopped the
   Disc (Resume Play/Multi-disc Resume) ····························· 1-7
Using the DVD’s Menu ························································· 1-8
Playing VIDEO CDs with PBC Functions (PBC Playback) ·  1-8
Playing an MP3 Audio Track ················································· 1-8
Various Play Mode Functions (Program Play, Shuffle Play,
   Repeat Play, A-B Repeat Play) ··········································· 1-9
Searching for a Scene ······························································ 1-10
Searching for a Title/Chapter/Track/Index/Scene
   (Search mode) ··································································· 1-10
Viewing Information About the Disc ······································· 1-10
Checking the Playing Time and Remaining Time ··············· 1-10
Sound Adjustments ·································································· 1-11
Changing the Sound ····························································· 1-11
TV Virtual Surround Settings (TVS) ··································· 1-11
Enjoying Movies ····································································· 1-12
Changing the Angles ···························································· 1-12
Displaying the Subtitles ······················································· 1-12
Adjusting the Picture Quality (BNR) ·································· 1-12
Adjusting the Playback Picture (CUSTOM PICTURE MODE) ·· 1-12
Enhancing the Playback Picture (DIGITAL VIDEO
   ENHANCER) ··································································· 1-13
Using Various Additional Functions ········································ 1-13
Locking Discs (CUSTOM PARENTAL CONTROL,
   PARENTAL CONTROL) ················································· 1-13
Controlling Your TV with the Supplied Remote ················· 1-14
Settings and Adjustments ························································ 1-15
Using the Setup Display ······················································ 1-15
Setting the Display or Sound Track Language
   (LANGUAGE SETUP) ···················································· 1-15
Settings for the Display (SCREEN SETUP) ······················· 1-15
Custom Settings (CUSTOM SETUP) ································· 1-15
Settings for the Sound (AUDIO SETUP) ···························· 1-16
Additional Information ···························································· 1-16
Troubleshooting ··································································· 1-16
Self-diagnosis Function (When letters/numbers appear in
   the display) ······································································· 1-17
Glossary ··············································································· 1-17
Language Code List ····························································· 1-18
2.
DISASSEMBLY
2-1.
DISASSEMBLY ······························································ 2-1
2-2.
UPPER CASE ································································· 2-1
2-3.
FRONT PANEL SECTION ············································· 2-2
2-4.
REAR PANEL ································································· 2-2
2-5.
MB-103 BOARD ····························································· 2-3
2-6.
CN-158 BOARD ····························································· 2-3
2-7.
AV-062 BOARD ······························································ 2-4
2-8.
ER-14 BOARD (AEP, UK) ············································· 2-4
2-9.
TABLE ASS’Y ································································ 2-4
2-10. LOADING MOTOR ASS’Y ··········································· 2-5
2-11. OPTICAL PICK-UP ························································ 2-5
2-12. POWER BLOCK ····························································· 2-6
2-13. IF-091 AND FR-187 BOARDS ······································ 2-6
2-14. INTERNAL VIEWS ························································ 2-7
2-15. CIRCUIT BOARDS LOCATION ··································· 2-8
3.
BLOCK DIAGRAMS
3-1.
OVERALL BLOCK DIAGRAM ···································· 3-1
3-2.
RF/SERVO BLOCK DIAGRAM ···································· 3-3
3-3.
SIGNAL PROCESSOR BLOCK DIAGRAM ················ 3-5
3-4.
SYSTEM CONTROL BLOCK DIAGRAM ··················· 3-7
3-5.
VIDEO BLOCK DIAGRAM (NC655P) ························· 3-9
3-6.
VIDEO BLOCK DIAGRAM (NC615) ························· 3-11
3-7.
AUDIO BLOCK DIAGRAM ········································ 3-13
3-8.
INTERFACE CONTROL BLOCK DIAGRAM ··········· 3-15
3-9.
POWER BLOCK DIAGRAM (1/2) ······························ 3-17
3-10. POWER BLOCK DIAGRAM (2/2) ······························ 3-19
4.
PRINTED WIRING BOARDS AND
SCHEMATIC DIAGRAMS
4-1.
FRAME SCHEMATIC DIAGRAM ································ 4-1
4-2.
PRINTED WIRING BOARDS AND SCHEMATIC
DIAGRAM ······································································ 4-4
WAVEFORMS ································································ 4-5
• MB-103(DVD/CD RF AMP, DIGITAL SERVO, MOTOR
DRIVE, SERVO, AV DECODER, SDRAM, SYSTEM
CONTROL, AUDIO DAC, PLL, I/P CONVERTER,
VIDEO ENCODER)
PRINTED WIRING BOARD ························· 4-7
• MB-103 (DVD/CD RF AMP, DIGITAL SERVO) (1/8)
SCHEMATIC DIAGRAM ···························· 4-11
• MB-103 (MOTOR DRIVE) (2/8)
SCHEMATIC DIAGRAM ···························· 4-13
• MB-103 (SERVO) (3/8)
SCHEMATIC DIAGRAM ···························· 4-15
• MB-103 (AV DECODER) (4/8)
SCHEMATIC DIAGRAM ···························· 4-17
• MB-103 (SDRAM) (5/8)
SCHEMATIC DIAGRAM ···························· 4-19
• MB-103 (SYSTEM CONTROL) (6/8)
SCHEMATIC DIAGRAM ···························· 4-21
• MB-103 (AUDIO DAC, PLL) (7/8)
SCHEMATIC DIAGRAM ···························· 4-23
• MB-103 (I/P CONVERTER, VIDEO ENCODER) (8/8)
SCHEMATIC DIAGRAM ···························· 4-25
• AV-062 (AUDIO OUT, VIDEO OUT)
PRINTED WIRING BOARD ······················· 4-29
• AV-062 (AUDIO OUT) (1/2)
SCHEMATIC DIAGRAM ···························· 4-31
• AV-062 (VIDEO OUT) (2/2)
SCHEMATIC DIAGRAM ···························· 4-33
• ER-14 (LINE1 OUT) (NC615:AEP,UK)
PRINTED WIRING BOARD ······················· 4-35
— 4 —
• ER-14 (LINE1 OUT) (NC615:AEP,UK)
SCHEMATIC DIAGRAM ···························· 4-37
• IF-091 (IF COM), PL-031 (LED)
PRINTED WIRING BOARDS ····················· 4-39
• IF-091 (IF COM)
SCHEMATIC DIAGRAM ···························· 4-41
• FR-187 (FUNCTION SW/LED)
PRINTED WIRING BOARD ······················· 4-43
• FR-187 (FUNCTION SW/LED)
SCHEMATIC DIAGRAM ···························· 4-45
• CN-158 (CONNECTOR)
PRINTED WIRING BOARD ······················· 4-47
• CN-158 (CONNECTOR)
SCHEMATIC DIAGRAM ···························· 4-49
• SE-130 (SENSOR), MD-94 (MD INTERFACE)
PRINTED WIRING BOARD ······················· 4-51
• SE-130 (SENSOR), MD-94 (MD INTERFACE)
SCHEMATIC DIAGRAM ···························· 4-53
• HS10S1U, HS10S1F (SWITCHING REGULATOR)
PRINTED WIRING BOARDS ····················· 4-55
• HS10S1U, HS10S1F (SWITCHING REGULATOR)
SCHEMATIC DIAGRAM ···························· 4-57
5.
IC PIN FUNCTION DESCRIPTION
5-1.
SYSTEM CONTROL PIN FUNCTION
(MB-103 BOARD IC104: MB91307RPFV-G-BND-E1) · 5-1
6.
TEST MODE
6-1.
GENERAL DESCRIPTION ··········································· 6-1
6-2.
STARTING TEST MODE ··············································· 6-1
6-3.
SYSCON DIAGNOSIS ··················································· 6-1
6-4.
DRIVE AUTO ADJUSTMENT ······································ 6-5
6-5.
DRIVE MANUAL OPERATION ··································· 6-7
6-6.
MECHA AGING ··························································· 6-11
6-7.
EMERGENCY HISTORY ············································ 6-11
6-8.
VERSION INFORMATION ········································· 6-11
6-9.
VIDEO LEVEL ADJUSTMENT ·································· 6-11
6-10. IF CON SELF DIAGNOSTIC FUNCTION ················· 6-12
6-11. TROUBLESHOOTING ················································ 6-19
6-12. MECHANISM TEST MODE  ADJUSTMENT ··········· 6-22
6-12-1. How to enter the mechanism test mode ······················ 6-22
6-12-2. Types of the mechanism test mode ····························· 6-22
6-12-3. Description of Each Mode ·········································· 6-22
7.
ELECTRICAL ADJUSTMENT
7-1.
POWER SUPPLY ADJUSTMENT ································· 7-1
1.
Power Supply Check (HS10S1U/HS10S1F Boards) ······ 7-1
7-2.
ADJUSTMENT OF VIDEO SYSTEM ··························· 7-2
1.
Video Level Adjustment (MB-103 Board) ······················ 7-2
2.
Progressive Video Output Level Adjustment
(MB-103 Board) ······························································ 7-2
3.
Checking S Video Output S-Y ········································· 7-2
4.
Checking S Video Output S-C ········································· 7-2
5.
Checking Component Video Output Y
(US, Canadian, Australian, PX Model) ··························· 7-3
6.
Checking Component Video Output B-Y
(US, Canadian, Australian, PX Model) ··························· 7-3
7.
Checking Component Video Output R-Y
(US, Canadian, Australian, PX Model) ··························· 7-3
8.
Checking RGB Output R (AEP, UK Model) ··················· 7-3
9.
Checking RGB Output G (AEP, UK Model) ·················· 7-4
10.
Checking RGB Output B (AEP, UK Model) ··················· 7-4
7-3.
ADJUSTMENT RELATED PARTS ARRANGEMENT ··· 7-5
8.
REPAIR PARTS LIST
8-1.
EXPLODED VIEWS ······················································ 8-1
8-1-1. OVERALL SECTION ····················································· 8-2
8-1-2. FRONT PANEL SECTION ············································· 8-3
8-1-3. LOADING SECTION ····················································· 8-4
8-1-4. CHASSIS SECTION ······················································· 8-5
8-2.
ELECTRICAL PARTS LIST ·········································· 8-6
— 5 —
1.
NOTE ON REMOVING THE UPPER
CASE
1)
Remove the four tapping screws and three screws. (See Fig. 1)
2)
Open the sides of case. (See Fig. 1)
3)
Remove the upper case in the direction of the arrow A.
2.
DISC REMOVAL PROCEDURE
1)
Insert a flat-head (-) screwdriver into a hole at the bottom, and
rotate the cam gear in the direction of the arrow A. (See Fig.2)
Two tapping screws
Two tapping screws
Three screws (B3)
A
3.
NOTE ON REMOVING THE TABLE
ASS’Y
1)
Remove the two screws. (See Fig. 3)
A
Cam gear
Table
Hole
Screw
(M2.6 
×
 8)
Screw
 (M2.6 
×
 8)
2)
Remove the two Plates (guide) in the direction of the arrows
A
 and B.
3)
Remove the Table ass’y in the direction of the arrow C.
4)
Remove the Flexible flat cable (See Fig. 4).
A
B
C
Plate (guide)
Plate (guide)
Table ass'y
Flexible flat cable
(FMS-18: CN002)
Fig. 1.
Fig. 2.
Fig. 3.
Fig. 4.
SERVICE NOTE
— 6 —
4.
NOTE ON MOUNTING THE GEARS
1)
Mount the gear (chuck). (See Fig. 5)
2)
Rotate the gear (chuck) in the direction of the arrow. (down
position) (See Fig. 5)
3)
Connect the boss of the gear (swing) with the groove of the
rotary encoder and mount the gear (swing). (See Fig. 6)
4)
Align triangle mark of the chassis with the groove of the gear
(swing).
Gear (chuck)
Gear (swing)
Gear (swing)
Boss
Groove
Align triangle mark of the chassis 
with the groove of the gear (swing). 
5)
Mount the gear (idler) while aligning the engagement of the
gear (swing) and the gear (chuck). (See Fig. 7)
Gear 
(idler)
Gear (idler)
Gear (chuck)
Gear (swing)
Engagement the gear (swing) and the gear (chuck).
Fig. 5.
Fig. 6.
Fig. 7.
— 7 —
5.
HOW TO  SERVICE THE  MB-103
BOARD
1)
Remove the upper case from the set. (Refer to section 2-1)
2)
Remove the MB-103 board. (Refer to section 2-4)
3)
Set the MB-103 board in the stand (with CK-121 board) as
shown in Fig. 9.
FFC 26P J-6090-117-A,
FFC 9P   J-6090-118-A,
FFC 15P J-6090-121-A,
FFC 25P J-6090-122-A,
FFC 11P J-6090-120-A
Harness 6P (J-6090-126-A)
CK-120 board
(J-6090-127-A)
Stand
(CK-121 board)
(J-6090-132-A)
Five flexible flat cables
Jig
4)
Set the CK-120 board in the place where the MB-103 board is
removed, as shown in Fig. 10.
3
 Connector (CN101)
2
 Stand
    (with CK-121 board)
1
 MB-103 board
4
 Two screws (B3)
5
 Connector
    
(CN109)
6
 Board to board
     connector (CN111)
1
 CK-120 
     board
2
 Four screws (B3)
4
 Flexible flat cable
    (FMO-6: CN103)
3
 Flexible flat cable
    (FMM-42: CN101)
7
 Flexible flat cable
    (FMC-15: CN107)
Fig. 8.
Fig. 9.
Fig. 10.
— 8 —
5)
Set the four flexible flat cables as shown in Fig. 11.
6)
Set the flexible flat cable and the harness as shown in Fig. 12.
4
 Connector
    
(CN110)
4
 Connector
    
(CN201)
5
 Harness
    
(6P: CN102)
3
 Flexible flat cable
    (FFC 25P: CN601)
4
 Connector
    
(CN102)
5
 Connector
    
(CN104)
6
 Connector
    
(CN108)
8
 Connector
    
(CN112)
3
 Flexible flat cable
    (FFC 11P: CN201)
7
 Flexible flat cable
    (FFC 15P: CN201)
2
 Flexible flat cable
    (FFC 9P: CN204)
1
 Flexible flat cable
    (FFC 26P: CN203)
7)
Set is finished.
Fig. 11.
Fig. 12.
— 9 —
CK-120 board
Mechanism deck
CN-158
MB-103
board
AV-62 board
Stand
(CK-121 board)
B to B Connector 9P
B to B Connector 9P
FFC 26P
(Used the set)
FFC  9P
(Used the set)
FFC 11P
(Used the set)
HARNESS 6P
HARNESS 6P
(Used the set)
FFC 26P
FFC  9P
FFC 11P
FFC15P
FFC25P
CN101
CN102
CN103
CN104
CN107
CN108
CN110
CN203
CN204
CN201
CN102
CN111
CN109
CN308
CN311
CN301
CN112
CN201
CN202
CN101
CN601
CN201
6.
CONNECTION OF SERVICE JIG
1-1
SECTION 1
GENERAL
DVP-NC615/NC655P
This section is extracted from instruction
manual. (DVP-NC615 : 3-074-252-11)
3
Precautions
• The power requirements and power 
consumption of this player are indicated on 
the back of the player. Check that the 
player’s operating voltage is identical with 
your local power supply.
Power requirements and 
power consumption 
t
On safety
• Caution – The use of optical instruments 
with this product will increase eye hazard.
• To prevent fire or shock hazard, do not 
place objects filled with liquids, such as 
vases, on the apparatus.
• Should any solid object or liquid fall into 
the cabinet, unplug the player and have it 
checked by qualified personnel before 
operating it any further.
On power sources
• The player is not disconnected from the AC 
power source as long as it is connected to 
the wall outlet, even if the player itself has 
been turned off.
• If you are not going to use the player for a 
long time, be sure to disconnect the player 
from the wall outlet. To disconnect the AC 
power cord, grasp the plug itself; never pull 
the cord.
• Should the AC power cord need to be 
changed, have it done at a qualified service 
shop only.
On placement
• Place the player in a location with adequate 
ventilation to prevent heat build-up in the 
player.
• Do not place the player on a soft surface 
such as a rug that might block the 
ventilation holes.
• Do not place the player in a location near 
heat sources, or in a place subject to direct 
sunlight, excessive dust, or mechanical 
shock.
• Do not install the player in an inclined 
position. It is designed to be operated in a 
horizontal position only.
• Keep the player and discs away from 
equipment with strong magnets, such as 
microwave ovens, or large loudspeakers.
• Do not place heavy objects on the player.
For the model supplied with the AC plug 
adaptor
If the AC plug of your unit does not fit into 
the wall outlet, attach the supplied AC plug 
adaptor.
On operation
• If the player is brought directly from a cold 
to a warm location, or is placed in a very 
damp room, moisture may condense on the 
lenses inside the player. Should this occur, 
the player may not operate properly. In this 
case, remove the disc and leave the player 
turned on for about half an hour until the 
moisture evaporates.
• When you move the player, take out any 
discs. If you don’t, the disc may be 
damaged.
On adjusting volume
Do not turn up the volume while listening to 
a section with very low level inputs or no 
audio signals. If you do, the speakers may be 
damaged when a peak level section is played.
On cleaning
Clean the cabinet, panel, and controls with a 
soft cloth slightly moistened with a mild 
detergent solution. Do not use any type of 
abrasive pad, scouring powder or solvent 
such as alcohol or benzine.
On cleaning discs
Do not use a commercially available cleaning 
disc. It may cause a malfunction.
IMPORTANT NOTICE
Caution: This player is capable of holding a 
still video image or on-screen display image 
on your television screen indefinitely. If 
you leave the still video image or on-screen 
display image displayed on your TV for an 
extended period of time you risk permanent 
damage to your television screen. 
Projection televisions are especially 
susceptible to this.
DVP–XXXX 
00V 00Hz
00W
NO. 
0-000-000-00
X
4
On transporting the player
Before transporting the player, follow the 
procedure below to return the internal 
mechanisms to their original positions.
1
Remove all the discs from the disc tray.
2
Press 
Z to close the disc tray.
Make sure that “NO DISC” appears on 
the front panel display.
3
Press 
?/1 to turn off the player.
The player enters standby mode and the 
power indicator lights up in red.
4
Disconnect the AC power cord.
If you have any questions or problems 
concerning your player, please consult your 
nearest Sony dealer.
7
About this Manual
• Instructions in this manual describe the 
controls on the remote. You can also use the 
controls on the player if they have the same 
or similar names as those on the remote.
• The meaning of the icons used in this 
manual is described below:
* MP3 (MPEG1 Audio Layer 3) is a standard 
format defined by ISO (International Standard 
Organization)/MPEG which compresses audio 
data.
This Player Can Play the 
Following Discs
The “DVD VIDEO” logo is a trademark.
Region code
Your player has a region code printed on the 
back of the unit and only will play DVD 
VIDEO discs (playback only) labeled with 
identical region codes. This system is used to 
protect copyrights.
DVDs labeled 
 will also play on this 
player.
If you try to play any other DVD, the message 
“Playback prohibited by area limitations..” 
will appear on the TV screen. Depending on 
the DVD, no region code indication may be 
labeled even though playing the DVD is 
prohibited by area restrictions.
Example of discs that the player 
cannot play
The player cannot play the following discs:
• All CD-ROMs (including PHOTO CDs)/
CD-Rs/CD-RWs other than those recorded 
in the following formats:
–music CD format
–video CD format
–MP3 format that conforms to ISO9660* 
Level 1/Level 2, or its extended format, 
Joliet
• Data part of CD-Extras
• DVD-RWs in VR mode
Check your model
The instructions in this manual are for 
DVP-NC615 sold in the U.S.A., Canada, 
Asia and Oceania. The differences between 
U.S./Canadian models and Asian/Oceanian 
models are the supplied remote 
commander, RMT-D143A for U.S./
Canadian models or RMT-D143E for 
Asian/Oceanian models, jack names on the 
rear panel, and some of the on-screen 
displays.
U.S./Canadian model is the one used for 
illustration purposes unless otherwise 
specified. Any difference in operation is 
clearly indicated in the text, for example, 
“Asian/Oceanian models only.”
Icon
Meaning
Functions available for DVD 
VIDEOs or DVD-Rs/DVD-
RWs in video mode
Functions available for VIDEO 
CDs or CD-Rs/CD-RWs in 
video CD format
Functions available for DATA 
CDs (CD-ROMs/CD-Rs/CD-
RWs containing MP3* audio 
tracks)
Functions available for music 
CDs or CD-Rs/CD-RWs in 
music CD format
Format of discs
DVD VIDEO
VIDEO CD
Music CD
ALL
DVP–XXXX 
00V 00Hz
00W
NO. 
0-000-000-00
X
Region code
8
• DVD-ROMs
• DVD Audio discs
• HD layer on Super Audio CDs
* A logical format of files and folders on CD-
ROMs defined by ISO (International Standard 
Organization).
Also, the player cannot play the following 
discs:
• A DVD with a different region code.
• A disc that has a non-standard shape (e.g., 
card, heart).
• A disc with paper or stickers on it.
• A disc that has the adhesive of cellophane 
tape or a sticker still left on it.
For U.S./Canadian models only:
• The player cannot play a disc recorded in a 
color system other than NTSC, such as PAL 
or SECAM (this player conforms to the 
NTSC color system).
Note
Some CD-Rs, CD-RWs, DVD-Rs, or DVD-RWs 
(in video mode) cannot be played on this player due 
to the recording quality or physical condition of the 
disc, or the characteristics of the recording device.
Furthermore, the disc will not play if it has not been 
correctly finalized. For more information, see the 
operating instructions for the recording device.
Note that discs created in the Packet Write format 
cannot be played.
Note on playback operations of 
DVDs and VIDEO CDs
Some playback operations of DVDs and 
VIDEO CDs may be intentionally set by 
software producers. Since this player plays 
DVDs and VIDEO CDs according to the disc 
contents the software producers designed, 
some playback features may not be available. 
Also, refer to the instructions supplied with 
the DVDs or VIDEO CDs.
Copyrights
This product incorporates copyright 
protection technology that is protected by 
method claims of certain U.S. patents, other 
intellectual property rights owned by 
Macrovision Corporation, and other rights 
owners. Use of this copyright protection 
technology must be authorized by 
Macrovision Corporation, and is intended for 
home and other limited viewing uses only 
unless otherwise authorized by Macrovision 
Corporation. Reverse engineering or 
disassembly is prohibited.
Notes about the Discs
• To keep the disc clean, handle the disc by its 
edge. Do not touch the surface.
• Do not expose the disc to direct sunlight or 
heat sources such as hot air ducts, or leave it 
in a car parked in direct sunlight as the 
temperature may rise considerably inside 
the car.
• After playing, store the disc in its case.
• Clean the disc with a cleaning cloth.
Wipe the disc from the center out.
• Do not use solvents such as benzine, 
thinner, commercially available cleaners, or 
anti-static spray intended for vinyl LPs.

Download Sony DVP-NC615 / DVP-NC655P / HT-5500D Service Manual (Repair Manual)

Here you can view online and download Sony DVP-NC615 / DVP-NC655P / HT-5500D Service Manual in PDF. DVP-NC615 / DVP-NC655P / HT-5500D service manual will guide through the process and help you recover, restore, fix, disassemble and repair Sony DVP-NC615 / DVP-NC655P / HT-5500D Audio. Information contained in service manuals typically includes schematics / circuit diagrams, wiring diagrams, block diagrams, printed wiring boards, exploded views, parts list, disassembly / assembly, pcb.