Read Sony DAV-TZ130 Service Manual online
HBD-TZ130
3
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40 °C higher
• Unleaded solder melts at a temperature about 40 °C higher
than ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350 °C.
Caution: The printed pattern (copper foil) may peel away if
about 350 °C.
Caution: The printed pattern (copper foil) may peel away if
the heated tip is applied for too long, so be careful!
• Strong
viscosity
Unleaded solder is more viscous (sticky, less prone to fl ow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
•
Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
also be added to ordinary solder.
NOTES ON CHIP COMPONENT REPLACEMENT
•
•
Never reuse a disconnected chip component.
•
Notice that the minus side of a tantalum capacitor may be dam-
aged by heat.
aged by heat.
FLEXIBLE CIRCUIT BOARD REPAIRING
•
•
Keep the temperature of soldering iron around 270 °C during
repairing.
repairing.
•
Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
circuit board (within 3 times).
•
Be careful not to apply force on the conductor when soldering
or unsoldering.
or unsoldering.
For European models:
Laser component in this product is capable of emitting radiation
exceeding the limit for Class 1.
exceeding the limit for Class 1.
This appliance is classifi ed as
a CLASS 1 LASER product.
This marking is located on the
rear exterior of unit.
a CLASS 1 LASER product.
This marking is located on the
rear exterior of unit.
CAUTION
Use of controls or adjustments or performance of procedures
other than those specifi ed herein may result in hazardous radia-
tion exposure.
Use of controls or adjustments or performance of procedures
other than those specifi ed herein may result in hazardous radia-
tion exposure.
• Abbreviation
AR :
AR :
Argentina
model
AUS :
Australian
model
BR
: Brazilian model
CH
: Chinese model
CND : Canadian model
E3
E3
: 240V AC area in E model
E12
: 220 – 240V AC area in E model
E32
: 110 – 240V AC area in E model
SAF
: South African model
SP
: Singapore model
TH :
Thai
model
Model
Part No.
SP model
GSE200276-0001
AUS model
GSE200276-0004
TH model
GSE200276-0007
CH model
GSE200276-0008
E32 model
GSE200276-0009
US model
GSE200276-0011
CND model
GSE200276-0012
E3, SAF model
GSE200276-0013
E12 model
GSE200276-0015
AR model
GSE200276-0017
BR model
GSE200276-0018
MODEL IDENTIFICATION
– Back Cabinet –
– Back Cabinet –
Parts No.
Ver. 1.2
Click on the first or last page to see other DAV-TZ130 service manuals if exist.