DAV-S500, DAV-S800, HCD-S800 - Sony Audio Service Manual (repair manual). Page 11

View Sony DAV-S500 / DAV-S800 / HCD-S800 Service Manual online

11
HCD-S500/S800
7. OPTICAL PICK-UP (KHM-240AAA)
1
 Floating screw (+PTPWHM 2.6)
2
 Flexible flat cable
     (9 core)
3
 Flexible flat cable
     (26 core)
4
 Step screw (L)
8
 Three insulators
9
 Optical pick-up
     (KHM-240AAA)
5
 Two step screws (M)
6
 Holder (KHM-240)
7
12
HCD-S500/S800
4-1. VERSION DISPLAY MODE
Procedure:
1.
Press the   A  button on the main unit or   1  button on the
remote commander to turn the set on.
2.
Press three buttons of  
FUNCTION 
,  .
  PREV
    and  A
simultaneously for two seconds.
3.
The message “VER. 1. ** ” is displayed for a moment.
4-2. JOG TEST  MODE
Procedure:
1.
Press the  A   button on the main unit or  1  button on the
remote commander to turn the set on.
2.
Press three buttons of  
BAND 
,  x  and  A  simultaneously.
3.
The fluorescent indicator displays “JOG 0”. The value “JOG
0” increases like +1, +2, +3... if rotating the VOLUME knob
clockwisw,or it decreases like –1, –2, –3,.... if rotating counter-
clockwise.
4.
To exit from this mode, press the  
POWER
  button to turn the
set off.
4-3. KEY TEST  MODE
Procedure:
1.
Press the  A    button on the main unit or  1    button on the
remote commander to turn the set on.
2.
Press three buttons of  
DISPLAY 
,  x  and  A  simultaneously.
3.
The message “KEY NUM 0” is displayed and “0” blinks.
4.
Each time a button is pressed, “KEY NUM 0” value increases.
However, once a button is pressed, it is no longer taken into
account.
5.
When all buttons are pressed, “KEY NUM 11” appears and
the number blinking is stopped.
6.
To exit from this mode, press the  
POWER 
 button to turn the
set off.
4-4. DISPLAY TEST  MODE
Procedure:
1.
Press the  A    button on the main unit or  1    button on the
remote commander to turn the set on.
2.
Press three buttons of 
 BAND 
,  X  and  A  simultaneously.
3.
All segments are turned on.
4.
When the  
NEXT
 >  button is pressed, the display will light
up as follows.
5.
Press the  
NEXT
 >  button, confirm the display.
6.
Press the  
NEXT
 >  button, all segments are turned off.
7.
Every pressing of the  
NEXT
  >    button turns on each
segments in the same order.
8.
To exit from this mode, press the  
POWER
  button to turn the
set off.
4-5. OSD TEST  MODE
Procedure:
1.
Press the  A    button on the main unit or  1    button on the
remote commander to turn the set on.
2.
Set the  
FUNCTION
  to DVD.
3.
While pressing two buttons of  
DISPLAY
  and
 x  simultaneously, turn the VOLUME knob clockwise.
4.
The Test Mode Menu is displayed on the TV screen.
5.
To execute each function, select the number on the remote
commander.
6.
See the following section for explanation in detail.
7.
To exit from this mode, press the  
POWER
  button to turn the
set off.
4-6. DISC TRAY  LOCK
Procedure:
1.
Press the  A    button on the main unit or  1    button on the
remote commander to turn the set on.
2.
Press two buttons of  
DISPLAY
  and  . 
PREV
simultaneously for two seconds.
3.
The message “LOCKED” is displayed and the tray is locked.
(Even if exiting from this mode, the tray is still locked.)
4.
Press two buttons of  
DISPLAY
  and  . 
PREV
 simultaneously for two seconds again.
5.
The message “UNLOCKED” is displayed and the tray is
unlocked.
6.
To exit from this mode, press the  
POWER
  button to turn the
set off.
4-7.
GENERAL  DESCRIPTION
The Test Mode allows you to make diagnosis and adjustment easily
using the remote commander and monitor TV. The instructions,
diagnostic results, etc. are given on the on-screen display (OSD).
[TEST DISC LIST]
Use the following test disc on test mode.
1) DVD reference disc
HLX-501 (J-6090-071-A) (dual layer)
HLX-503 (J-6090-069-A) (single layer)
HLX-504 (J-6090-088-A) (single layer)
HLX-505 (J-6090-089-A) (dual layer)
2) SACD reference disc
HLXA-509 (J-6090-090-A)
Note:
Do not use exiting test disc for DVD.
4-8.
STARTING  TEST  MODE
Set the FUNCTION to DVD with the main unit power on. Next,
while pushing the  x  button and the [DISPLAY] button on the main
unit at the same time, turn the VOLUME knob to the right to start
Test Mode and display the menu shown below on the TV screen. At
the bottom of the menu screen, the model name and revision number
are displayed.
To  execute each function, select the desired menu and press its
number on the remote commander. To exit from Test Mode, press
the [POWER] button.
Test Mode Menu
0. Syscon Diagnosis
1. Drive Auto Adjustment
2. Drive Manual Operation
3. Mecha Aging
4. Emergency History
5. Version Information
6. Video Level Adjustment
                Exit: POWER Key
_
Model
: HCX-1030_xx
Revision : 1.xxx
SECTION 4
TEST MODE
ALL 1 DISCS  AUTO
TITLE
TRACK
CHAPTER
INDEX
HTUNED
M MONO
ST S
dB  REPEAT  1
kHz  PROGRAM
MHz  SHUFFLE
PRO  LOGIC
DIGITAL  FM  AM
NTSC  PBC  ANGLE
D
D
D
D
dts PCM
ALL 1 DISCS  AUTO
TITLE
TRACK
CHAPTER
INDEX
HTUNED
M MONO
ST S
dB  REPEAT  1
kHz  PROGRAM
MHz  SHUFFLE
PRO  LOGIC
DIGITAL  FM  AM
NTSC  PBC  ANGLE
D
D
D
D
dts PCM
Ver 1.6  2003.07
13
HCD-S500/S800
4-9.
SYSCON  DIAGNOSIS
The same contents as board detail check by serial interface can be
checked from the remote commander.
On the Test Mode Menu screen, press 
[0]
 key on the remote
commander, and the following check menu will be displayed.
### Syscon Diagnosis ###
Check Menu
0. Quit
1. All
2. Version
3. Peripheral
4. Servo
5. Supply
6. AV Decoder
7. Video
8. Audio
9. DSD Decoder
_
0.
Quit
Quit the Syscon Diagnosis and return to the Test Mode Menu.
1.
All
All items continuous check
This menu checks all diagnostic items continuously. Normally, all
items are checked successively one after another automatically
unless an error is found, but at a certain item that requires judgment
through a visual check to the result, the following screen is displayed
for the key entry.
### Syscon Diagnosis ###
Diag All Check
No. 2 Version
 2-3. ROM Check Sum
Check Sum = 2005
Press NEXT Key to Continue
Press PREV Key to Repeat
_
For the ROM Check, the check sum calculated by the Syscon is
output, and therefore you must compare it with the specified value
for confirmation.
Following the message, press 
[NEXT]
 key to go to the next item, or
[PREV]
 key to repeat the same check again. To quit the diagnosis
and return to the Check Menu screen, press  x  or 
[ENTER]
 key. If
an error occurred, the diagnosis is suspended and the error code is
displayed as shown below.
### Syscon Diagnosis ###
 3-3. EEPROM Check
Error 03: EEPROM Write/Reed N
Address
: 00000001
Write Data : 2492
Read Data
: 2490
Press NEXT Key to Continue
Press PREV Key to Repeat
_
Press  x  key to quit the diagnosis, or 
[PREV]
 key to repeat the
same item where an error occurred, or 
[NEXT]
 key to continue the
check from the item next to faulty item.
Selecting 2 and subsequent items calls the submenu screen of each
item.
For example, if “5. Supply” is selected, the following submenu will
be displayed.
### Syscon Diagnosis ###
Check Menu
No. 5 Supply
0. Quit
1. All
2. ARP Register Check
3. ARP to RAM Data Bus
4. ARP to RAM Address Bus
5. ARP RAM Check
_
0.
Quit
Quit the submenu and return to the main menu.
1.
All
All submenu items continuous check
This menu checks 2 and subsequent items successively. At the item
where visual check is required for judgment or an error occurred,
the checking is suspended and the message is output for key entry.
Normally, all items are checked successively one after another
automatically unless an error is found.
Selecting 2 and subsequent items executes respective menus and
outputs the results.
For the contents of each submenu, see “Check Items List”.
General Description of Checking Method
2.
Version
(2-2) Revision
ROM revision number is displayed.-
Error: Not detected.
The revision number defined in the source file of ROM (At
the beginning of mass production, the Flash ROM of IC107
is used, but midway it is replaced by the IC108 OTP ROM.
IC107 or IC108) is displayed with four digits.
Below IC107 are all IC107 or IC108.
(2-3) ROM Check Sum
Check sum is calculated.
Error: Not detected.
The 8-bit data are added at addresses 0x000F0000 ~
0x002EFFFF of ROM (IC107) and the result is displayed
with 4-digit hexadecimal number. Error is not detected.
Compare the result with the specified value.
(2-4) Model Type
Model code is displayed.
Error: Not detected.
The model code read from EEPROM (IC101) is displayed
with 2-digit hexadecimal number.
(2-5) Region
Region code is displayed.
Error: Not detected.
The region code determined from the model code is displayed.
14
HCD-S500/S800
3.
Peripheral
(3-2) EEPROM Check
Data write 
→ read, and accord check
Error 03: EEPROM write/read discord
Data 0x9249, 0x2942, 0x4294 are written to addresses
0x00~0xFF of EEPROM (IC101), then read and checked.
Before writing, the data are saved, then after checking, they
are written to restore the contents of EEPROM.
4.
Servo
(4-2) Servo DSP Check
Data write 
→ read, and accord check
Error 12: Read data discord
Data 0x9249, 0x2942, 0x4294 are written to the address
0x602 of RAM in the Servo DSP (IC302), then read and
checked.
(4-3) DSP Driver Test
Test signal data 
→ DSP Driver
Error: Not detected.
Caution: Do not conduct this test with a mechanical deck
connected.
The maximum voltage is applied to the Servo Driver IC
(IC401, IC802). If mechanical deck is connected, the mo-
tor and optics could be damaged. Disconnect mechanical
deck following the output message, then enter specified 4-
or 5-digit number from the remote commander, and press
the 
[ENTER]
. The test is conducted only when the input
data accord. Check the output level, then press the 
[NEXT]
to finish the test.
This test is skipped if “All” is selected.
Supplement: How to disconnect mechanical deck
Disconnect flat cables connected to the CN009 and CN010
of MB-82/85 board. Also, disconnect harness from the
CN402.
5.
Supply
Caution: Do  not conduct this check with a mechanical deck
connected.
An access is made to the stream supply and servo control
IC (IC302) and external RAM (IC303) using check data.
If mechanical deck is connected, the motor and optics
could be damaged. This check is also executed by the “All”
menu item.
Supplement: How to disconnect mechanical deck
Disconnect flat cables connected to the CN009 and
CN010 of DVD board. Also, disconnect harness from
the CN402.
(5-2) ARP Register Check
Data write 
→ read, and accord check
Error 08: ARP register write, and read data discord
Data 0x00 to 0xFF are written to the TMAX register (ad-
dress 0xC6) in ARP (IC302), then they are read and checked.
(5-3) ARP to RAM Data Bus
Data write 
→ read, and accord check
Error 09: ARP 
←→ RAM data bus error
Data 0x0001 to 0x8000 where one bit each is set to 1 are
written to the address 0 of RAM (IC303) connected to the
ARP (IC302) through the bus, then they are read and
checked. In case of discord, written bit pattern and read
data are displayed. If data where multiple bits are 1 are
read, the bits concerned may touch each other. Further, if
data where certain bit is always 1 or 0 regardless of written
data, the line could be disconnected or shorted.
(5-4) ARP to RAM Address Bus
Data write 
→ other address read discord check
Error 10: ARP 
→ RAM address bus error
Caution: Address and data display in case of an error is
different from the display of other diagnosis (de-
scribed later).
Before starting the test, all addresses of RAM (IC303) are
cleared to 0x0000.
First, 0xA55A is written to the address 0x00000, and the
address data are read and checked from addresses 0x00001
to 0x80000 while shifting 1 bit each. Next, the data at that
address is cleared, and it is written to the address 0x00001,
and read and checked in the same manner. This check is
repeated up to the address 0x80000 while shifting the ad-
dress data by 1 bit each.
If data other than 0 is read at the addresses except written
address, an error is given because all addresses were al-
ready cleared to 0. In this check, the error display pattern is
different from that of other diagnosis; read data, written
address, and read address are displayed in this order. How-
ever, the message uses same template, and accordingly ex-
change Address and Data when reading. The following dis-
play, for example,
### Syscon Diagnosis ###
 5-4. ARP to RAM Address Bus
Error 10: ARP - RAM Address B
Address
: 0000A55A
Write Data : 00000000
Read Data
: 00080000
Press NEXT Key to Continue
Press PREV Key to Repeat
_
shows the data 0xA55A was read from address 0x00080000
though it was written to the address 0x00000000. This im-
plies that these addresses are in the form of shadow. Also,
if the read data is not 0xA55A, another error will be present.
(5-5) ARP RAM Check
Data write 
→ read, and accord check
Error 11: ARP RAM read data discord
The program code data stored in ROM are copied to all
areas of RAM (IC303) connected to the ARP (IC302)
through the bus, then they are read and checked if they ac-
cord. If the detail check was selected initially, the data are
written to all areas and read, then the same test is conducted
once again with the data where all bits are inverted between
1 and 0. If discord is detected, faulty address, written data,
and read data are displayed following the error code 11,
and the test is suspended.
15
HCD-S500/S800
6.
AV Decoder
(6-2) 1930 RAM
Data write 
→ read, and accord check
Error 13: AVD RAM read data discord
The program code data stored in ROM (IC107 or IC108)
are copied to all areas oo»RAM (IC504, IC505) connected
to the AVD (IC503) through the bus, then they are read and
checked if they accord. Further, the same test is conducted
once again with the data where all bits are inverted between
1 and 0. If discord is detected, faulty address, written data,
and read data are displayed following the error code 13,
and the test is suspended.
(6-3) 1930 SP
ROM 
→ AVD RAM → Video OUT
Error: Not detected.
The data including sub picture streams in ROM (IC107 or
IC108) are transferred to the RAM (IC504, IC505) in AVD
(IC503), and output as video signals from the AVD (IC503).
They are output from all video terminals (Composite, Y/C).
7.
Video
(7-2) Color Bar
AVD color bar command write 
→ Video OUT
Error: Not detected.
The command is transferred to the AVD, and the color bar
signals are output from video terminals.
They are output from all video terminals (Composite, Y/C).
(7-3) Composit Out
(7-4) Y/C Out
(7-6) Component Out
8.
Audio
(8-2) ARP 
→ 1930
Error 14
: ARP 
→ 1930 video NG
         15
: ARP 
→ 1930 audio NG
(8-3) Test Tone
All channels
2ch Left
2ch Right
Front Left
Front Right
Rear Left
Rear Right
Center
Sub Woofer
9.
DSD Decoder
(9-2) 2752 ID Chack
(9-3) 2752 RAM Check
Check Items List
2) Version
(2-2) Revision
(2-3) ROM Check Sum
(2-4) Model Type
(2-5) Region
3) Peripheral
(3-2) EEPROM Check
4) Servo
(4-2) Servo DSP Check
(4-3) DSP Driver Test
5) Supply
(5-2) ARP Register Check
(5-3) ARP to RAM Data Bus
(5-4) ARP to RAM Address Bus
(5-5) ARP RAM Check
6) AV Decoder
(6-2) 1930 RAM
(6-3) 1930 SP
7)
Video
(7-2) Color Bar
(7-3) Composit Out
(7-4) Y/C Out
(7-6) Component Out
8) Audio
(8-2) ARP 
→ 1930
(8-3) Test Tone
9) DSD Decoder
(9-2) 2752 ID Check
(9-3) 2752 RAM Check
Error Codes List
00: Error not detected
01: RAM write/read data discord
02: Gate array NG
03: EEPROM NG
08: ARP register read data discord
09: ARP 
←→ RAM data bus error
10: ARP 
←→ RAM address bus error
11: ARP RAM read data discord
12: Servo DSP NG
13: 1930 SDRAM NG
14: ARP 
→ 1930 video NG
15: ARP 
→ 1930 audio NG
16: 1910 UCODE download NG
17: System call error (function not supported)
18: System call error (parameter error)
19: System call error (illegal ID number)
20: System call error (time out)
90: Error occurred
91: User verification NG
92: Diagnosis cancelled
16
HCD-S500/S800
4-10.
DRIVE  AUTO  ADJUSTMENT
On the Test Mode Menu screen, press 
[1]
  key on the remote
commander, and the drive auto adjustment menu will be displayed.
## Drive Auto Adjustment ##
Adjustment Menu
0. ALL
1. DVD-SL
2. CD
3. DVD-DL
4. LCD
Exit: RETURN
Normally, 
[0]
 is selected to adjust DVD (single layer), CD, DVD
(dual layer), and SACD in this order. But, individual items can be
adjusted for the case where adjustment is suspended due to an error.
In this mode, the adjustment can be made easily through the
operation following the message displayed on the screen.
The disc used for adjustment must be the one specified for
adjustment. However, for SACD disc, use the player with initial
data if the disc is not available.
Note
:
After parts related to the servo circuit (RF amplifier, DSP, motor
driver, EEPROM (IC101) so on) are replaced, re-adjusting the servo
circuit is necessary. Select “ALL” at “DRIVE AUTO
ADJUSTMENT ” and adjust DVD-SL (single layer), CD and
DVD-DL (dual layer).
0.
ALL
Select 
[0]
  and press 
[ENTER]
  key,  and the servo set data in
EEPROM will be initialized. Then, 1. DVD-SL disc, 2. CD disc, 3.
DVD-DL disc, and 4. SACD disc are adjusted in this order. Each
time one disc was adjusted, it is ejected. Replace it with the specified
disc following the message. Though the message to confirm whether
discs other than SACD disc are adjusted is not displayed, you can
finish the adjustment if pressing the  x  button. During adjustment
of each disc, the measurement for disc type judgment is made. As
automatic adjustment does not judge the disc type unlike
conventional models, take care not to insert wrong type discs. Also,
do not give a shock during adjustment.
1.
DVD-SL (single layer)
Select 
[1]
, insert DVD single layer disc, and press 
[ENTER]
 key,
and the adjustment will be made through the following steps, then
adjusted values will be written to the EEPROM.
DVD Single Layer Disc Adjustment Steps
1. SLED TILT Reset
2. Disc Check Memory SL
3. Wait 300 msec
4. Set Disc Type SL
5. LD ON
6. Spdl Start
7. Wait 1 sec
8. Focus Servo ON 0
9. Auto Track Offset Adjust
10. CLVA ON
11. Wait 500 msec
12. Tracking ON
13. Wait 1 sec
14. Sled ON
15. Check CLV Lock
16. Auto LFO Adjust
17. Auto Focus Offset Adjust
18. Auto Tilt Position Adjust
19. Auto Focus Gain Adjust
20. Auto Focus Offset Adjust
21. EQ Boost Adjust
22. Auto LFO Adjust
23. Auto Track Gain Adjust, Search Check
24. 32Tj Fwd
25. 32Tj Rev
26. 500Tj Fwd
27. 500Tj Rev
28. All Servo Stop
29. Eep Copy Loop Filter Offset
Ver 1.6  2003.07
17
HCD-S500/S800
2.
CD
Select 
[2]
, insert CD disc, and press 
[ENTER]
 key, and the
adjustment will be made through the following steps, then adjusted
values will be written to the EEPROM.
CD Adjustment Steps
1. Sled Tilt Rest
2. Disc Check Memory CD
3. Wait 500 msec
4. Set Disc Type CD
5. LD ON
6. Spdl Start
7. Wait 500 msec
8. Focus Servo ON 0
9. Auto Track Offset Adjust
10. CLVA ON
11. Wait 500 msec
12. Tracking ON
13. (TC Display Start)
14. Wait 1 sec
15. Jitter Display Start
16. Sled ON
17. Check CLV ON
18. Auto LFO Adjust
19. Auto Focus Offset Adjust
20.
21. Auto Focus Gain Adjust
22. Auto Focus Offset Adjust
23. Eq Boost Adjust
24. Auto LFO Adjust
25. Auto Track Gain Adjust, Search Check
26. 32Tj Fwd
27. 32Tj Rev
28. 500Tj Fwd
29. 500Tj Rev
30. All Servo Stop
3.
DVD-DL (dual layer)
Select 
[3]
, insert DVD dual layer disc, and press 
[ENTER]
 key, and
the adjustment will be made through the following steps, then
adjusted values will be written to the EEPROM.
DVD Dual Layer Disc Adjustment Steps
1. Sled Tilt Reset
2. Disc Check Memory DL
3. Wait 500 msec
4. Set Disc Type DL
5. LD ON
6. Spdl Start
7. Wait 1 sec, Layer 1 Adjust
8. Focus Servo ON 0
9. Auto Track Offset Adjust
10. Clva ON
11. Wait 500 msec
12. Tracking ON
13. Wait 500 msec
14. Sled ON
15. Check CLV Lock
16. Auto Loop Filter Offset Auto Focus Adjust
17.
18. Auto Focus Gain Adjust
19. Auto Focus Offset Adjust
20. Eq Boost Adjust
21. Auto Loop Filter Offset
22. Auto Track Gain Adjust, Search Check
23. 32Tj Fwd
24. 32Tj Rev
25. 500Tj Fwd
26. 500Tj Rev, Layer 0 Adjust
27. Fj (L1 -> L0)
28. Auto Track Offset Adjust L0
29. Clva ON
30. Wait 500 msec
31. Tracking ON
32. Wait 500 msec
33. Sled ON
34. Check CLV Lock
35. Auto Focus Filter Offset
36. Auto Focus Adjust
37.
38. Auto Focus Gain Adjust
39. Auto Focus Offset Adjust
40. Eq Boost Adjust
41. Auto Loop Filter Offset
42. Auto Track Gain Adjust, Search Check
43. 32Tj Fwd
44. 32Tj Rev
45. 500Tj fwd
46. 500Tj Rev, Layer Jump Check
47. Lj (L0 -> L1)
48. Lj (L1 -> L0)
49. All Servo Stop
18
HCD-S500/S800
4.
LCD
Select 
[4]
, insert SACD disc, and press 
[ENTER]
 key, and the
adjustment will be made through the following steps, then adjusted
values will be written to the EEPROM. However, if SACD disc is
not available, use the player with initial data, skipping the SACD
adjustment. In this case, you can finish the adjustment if pressing
the  x  button.
SACD Adjustment Steps
1. Sled Tilt Reset
2. Set Disc Type CD
3. LD ON
4. Spdl Start
5. Wait 500 msec
6. Focus Servo ON 0
7. Auto track Offset Adjust
8.
9. CLVA ON
10. Wait 500 msec
11. Tracking ON
12. Wait 1 sec
13. Sled ON
14. Check CLV ON
15. Auto Focus Offset Adjust
17.
18. Auto Focus Gain Adjust
19. Auto Focus Offset Adjust
20. Eq Boost Adjust
21. Auto LFO Adjust
22. Auto Track Gain Adjust
23. 32Tj Fwd
24. 32Tj Rev
25. 500Tj Fwd
26. 500Tj Rev
27. All Servo Stop */
4-11. DRIVE  MANUAL  OPERATION
On the Test Mode Menu screen, select 
[2]
, and the manual operation
menu will be displayed. For the manual operation, each servo on/
off control and adjustment can be executed manually.
## Drive Manual Operation ##
Operation Menu
1. Disc type
2. Servo Control
3. Track/Layer Jump
4. Manual Adjustment
5. Auto Adjustment
6. Memory Check
7. Sacd Water Mark
0. Disc Check Memory
_
Exit: Return
In using the manual operation menu, take care of the following
points. These commands do not provide protection, thus requiring
correct operation. The sector address or time code field is displayed
when a disc is loaded.
1. Set correctly the disc type to be used on the Disc Type
screen.
The disc type must be set after a disc was loaded.
The set disc type is cleared when the tray is opened.
2. After power ON, if the Drive Manual Operation was
selected, first perform “Reset SLED TILT” by opening 1.
Disc Type screen.
3. In case of an alarm, immediately press the  x  button to
stop the servo operation, and turn the power OFF.
Basic operation (controllable from front panel or remote
commander)
[POWER]
Power OFF
 x
Servo stop
[OPEN/CLOSE]
Stop+Eject/Loading
[RETURN]
Return to Operation Menu or Test Mode
Menu
[NEXT]
[PREV]
Transition between sub modes of menu
[1]
 to 
[9]
[0]
Selection of menu items
Cursor UP/DOWN
Increase/Decrease in manually adjusted
value
19
HCD-S500/S800
0.
Disc Check Memory
Disc Check
1. SL Disc Check
2. CD Disc Check
3. DL Disc Check
0. Reset SLED TILT
_
On this screen, the mirror time is measured to judge the disc and it
is written to the EEPROM. First load DVD SL disc and press 
[1]
,
next load CD disc and press 
[2]
, and finally load DVD DL disc and
press 
[3]
.
The adjustment must be executed more than once after default data
were written. External vibration or shock to the player must not be
given. Reference value for DVD is from 10 to 20, and for CD, from
28 to 4F.
Check that the value of CD is larger than that of DVD.
When those values are beyond a range perform this adjustment again.
From this screen, you can go to another mode by pressing 
[NEXT]
or 
[PREV]
 key, but you cannot enter this mode from another mode.
You can enter this mode from the Operation Menu screen only.
1.
Disc Type
Disc Type
1. Disc Type Auto Check
2. DVD SL
12 cm
3. DVD DL
12 cm
4. CD
12cm
5. LCD
12 cm
6. DVD SL
8 cm
7. DVD DL
8 cm
8. CD
8 cm
9. LCD
8 cm
0. Reset SLED TILT
-- SA. ------ SI. --
EMG. 00
DVD SL12cm
On this screen, select the disc type. To select the disc type, press the
number of the loaded disc. The selected disc type is displayed at the
bottom. Selecting 
[1]
 automatically selects and displays the disc
type. In case of wrong display, retry “Disc Check Memory”. Also,
opening the tray causes the set disc type to be cleared. In this case,
set the disc type again after loading.
In performing manual operation, the disc type must be set.
Once the disc type has been selected, the sector address or time
code display field will appear as shown below. These values are
displayed when PLL is locked.
Disc Type
1. Disc Type Auto Check
2. DVD SL
12 cm
3. DVD DL
12 cm
4. CD
12cm
5. LCD
12 cm
6. DVD SL
8 cm
7. DVD DL
8 cm
8. CD
8 cm
9. LCD
8 cm
0. Reset SLED TILT
SA.      SI.    EMG. 00
DVD SL 12 cm
Display when DVD SL 12cm disc was selected
Disc Type
1. Disc Type Auto Check
2. DVD SL
12 cm
3. DVD DL
12 cm
4. CD
12cm
5. LCD
12 cm
6. DVD SL
8 cm
7. DVD DL
8 cm
8. CD
8 cm
9. LCD
8 cm
0. Reset SLED TILT
TC.   :   :    EMG. 00
CD   12 cm
Display when CD 12cm disc was selected
[0]
Reset SLED TILT
Reset the Sled and Tilt to initial position.
[1]
Disk Type Check
Judge automatically the loaded disc. As
the judged result is displayed at the
bottom of screen, make sure that it is
correct.
If Disc Check Memory menu has not
been executed after EEPROM default
setting, the disc type cannot be judged.
In this case, return to the initial menu
and make a check for three types of discs
(SL, DL, CD).
[2]
 to 
[9]
Select the loaded disc. The adjusted
value is written to the address of selected
disc. No further entry is necessary if 
[1]
was selected.
2. Servo Control
Servo Control
1. LD
Off R.Sled FWD
2. SP
Off L.Sled REV
3. Focus
Off
4. TRK.
Off
5. Sled
Off
6. CLVA
Off
7. FCS. Srch Off
0. Reset SLED TILT
SA.      SI.    EMG. 00
DVD SL 12 cm
On this screen, the servo on/off control necessary for replay is
executed. Normally, turn on each servo from 1 sequentially and
when CLVA is turned on, the usual trace mode becomes active. In
the trace mode, DVD sector address or CD time code is displayed.
This is not displayed where the spindle is not locked.
The spindle could run overriding the control if the spindle system is
faulty or RF is not present. In such a case, do not operate CLVA.
20
HCD-S500/S800
[0]
Reset SLED TILT
Reset the Sled and Tilt to initial position.
[1]
LD
Turn ON/OFF the laser.
[2]
SP
Turn ON/OFF the spindle.
[3]
Focus
Search the focus and turn on the focus.
[4]
TRK
Turn ON/OFF the tracking servo.
[5]
Sled
Turn ON/OFF the sled servo.
[6]
CLVA
Turn ON/OFF normal servo of spindle
servo.
[7]
FCS. Srch
Apply  same voltage as that of focus
search to the focus drive to check the
focus drive system.
→ Sled FWD
Move  the sled outward. Perform this
operation with the tracking servo turned
off.
← Sled REV
Move  the sled inward. Perform this
operation with the tracking servo turned
off.
↑ Tilt UP
Move the tilt upward.
↓ Tilt DOWN
Move the tilt downward.
The following menus are normally not used.
3.
Track/Layer Jump
4.
Manual Adjustment
5.
Auto Adjustment
The persons who do not know well about these menus should not
use them.
6. Memory Check
EEPROM Data1
            -– DL –-
 CD LCD
SL
L0
L1
Focus Gain
xx xx
xx
xx
xx
TRK. Gain
xx xx
xx
xx
xx
FCS Balance
xx xx
xx
xx
xx
Focus Bias
xx xx
xx
xx
xx
TRV. Offset
xx xx
xx
xx
xx
L. F. Offset
xx xx
xx
xx
xx
EQ Boost
xx xx
xx
xx
xx
Mirror Time
xx xx
xx
xx
xx
_DOWN: Next Data
CLEAR: Default Set     page.1/2
EEPROM Data1
            -– DL –-
 CD LCD
SL
L0
L1
RF Jitter
xx --
xx
xx
xx
RF Level
xx --
xx
--
--
FE Level
xx --
xx
--
--
FE Balance
xx --
xx
--
--
TRV. Level
xx --
xx
--
--
Analog FRSW
xx xx
xx
xx
xx
PLL DacGain
xx xx
xx
xx
xx
_
 UP  : Prev Data
CLEAR: Default Set     page.2/2
This screen displays current servo adjusted data stored in the
EEPROM. Though adjusted data can be initialized with the 
[CLEAR]
key, they cannot be restored after initialization.
So, before clearing, make a note of the adjusted data.
For reference, the drive has been designed so that the gain center
value is 20 and offset value is 80. Other values will be in a range of
10 to 80. If extreme value such as 00 or FF is set, adjustment will be
faulty. In such a case, check for disc scratch or cable disconnection,
then perform adjustment again.
7. Sacd Water Mark
4-12. MECHA  AGING
### Mecha Aging ###
Press OPEN Key
Abort: STOP key
On the Test Mode Menu Screen, selecting [3] executes the aging of
the mechanism. Start aging with PLAY. During aging, the repeat
cycle is displayed. Aging can be aborted at any time by pressing the
 x  key. After the operation is stopped, press the  x  key or [RETURN]
key again to return to the Test Mode Menu. SEARCH Aging is only
for a CD.

Click on the first or last page to see other DAV-S500 / DAV-S800 / HCD-S800 service manuals if exist.