Read Sony DAV-LF1H Service Manual online
US Model
Canadian Model
AEP Model
UK Model
E Model
Australian Model
Chinese Model
DAV-LF1H
HCR-LF1H/SA-LF1H
SERVICE MANUAL
DVD HOME THEATRE SYSTEM
Sony Corporation
Home Audio Division
Published by Sony Techno Create Corporation
9-887-282-03
2006J16-1
© 2006.10
• DAV-LF1H is composed of following models. As for the service
manual, it is issued for each component model, then, please
refer to them.
refer to them.
Ver. 1.2 2006. 10
COMPONENT MODEL NAME
HCR-LF1H is composed of HCD-LF1H, AC-LF1HR, SA-WSLF1H.
SA-LF1H is composed of SS-CTLF1H/TSLF1H/TSLF1HW, SA-TSLF1H.
SA-LF1H is composed of SS-CTLF1H/TSLF1H/TSLF1HW, SA-TSLF1H.
The units that are required for the system operation check during repair service
Unit.
required for checking
required for checking
Unit to be checked
DVD player:
HCD-LF1H
Subwoofer:
SA-WSLF1H
Front speaker:
SS-TSLF1H
Center speaker:
SS-CTLF1H
Surround speaker (L):
SA-TSLF1H
AC adaptor:
AC-LF1HR
Surround speaker (R):
SS-TSLF1HW
Remote commander:
RM-ADP011
HCD-LF1H
Subwoofer:
SA-WSLF1H
Front speaker:
SS-TSLF1H
Center speaker:
SS-CTLF1H
Surround speaker (L):
SA-TSLF1H
AC adaptor:
AC-LF1HR
Surround speaker (R):
SS-TSLF1HW
Remote commander:
RM-ADP011
DVD player:
HCD-LF1H
HCD-LF1H
Subwoofer:
SA-WSLF1H
SA-WSLF1H
Front speaker:
SS-TSLF1H
SS-TSLF1H
Center speaker:
SS-CTLF1H
SS-CTLF1H
Surround speaker
(L): SA-TSLF1H
(L): SA-TSLF1H
AC adaptor:
AC-LF1HR
AC-LF1HR
Surround speaker
(R): SS-TSLF1HW
(R): SS-TSLF1HW
*1 Only the defective unit.
Units with mark: The units that are required for the system operation check during repair service.
(However, there can be a case that some units of the system need to not be brought into repair shop depending on the unit.that become defective.)
Units with mark: The units that are required for the system operation check during repair service.
(However, there can be a case that some units of the system need to not be brought into repair shop depending on the unit.that become defective.)
*1
EXCEPT
US, CND
US, CND
DAV-LF1H
DAV-LF1H
–
HCR-LF1H
HCD-LF1H
HCD-LF1H
AC-LF1HR
AC-LF1HR
SA-WSLF1H
SA-WSLF1H
–
SA-LF1H
SS-TSLF1H
SS-TSLF1H
SS-CTLF1H
SS-CTLF1H
SA-TSLF1H
SA-TSLF1H
SS-TSLF1HW
SS-TSLF1HW
Package Main
CONTROL UNIT (DVD Player)
AC ADAPTOR
SUBWOOFER
Package Speaker
FRONT SPEAKER
CENTER SPEAKER
SURROUND SPEAKER (L ch)
SURROUND SPEAKER (R ch)
DAV-LF1H
2
1
4
2
6
6
7
5
3
8
9
10
11
12
13
14
15
17
16
18
20
19
21
23
24
22
25
19
●DIR-R3
●DIR-T1
●CALIBRATION
MIC
MIC
●STAND
(HCD-LF1H)
(HCD-LF1H)
●STAND COVER
●SCREW
(HCD-LF1H)
(HCD-LF1H)
●AJUSTER and
CUSHON
(SS-CTLF1H)
CUSHON
(SS-CTLF1H)
●STAND
and FOOT
(SS-CTLF1H)
and FOOT
(SS-CTLF1H)
●SCREW
(SS-CTLF1H)
(SS-CTLF1H)
●SCREW
(SS-TSLF1H,
SA-TSLF1H,
SS-TSLF1HW)
(SS-TSLF1H,
SA-TSLF1H,
SS-TSLF1HW)
●POST
(SS-TSLF1H,
SA-TSLF1H,
SS-TSLF1HW)
(SS-TSLF1H,
SA-TSLF1H,
SS-TSLF1HW)
●BASE
(SS-TSLF1H,
SA-TSLF1H,
SS-TSLF1HW)
(SS-TSLF1H,
SA-TSLF1H,
SS-TSLF1HW)
●CORD CLAMP
(SA-TSLF1H)
(SA-TSLF1H)
●SPEAKER
ADAPTOR
and COVER
(SS-TSLF1H,
SA-TSLF1H,
SS-TSLF1HW)
ADAPTOR
and COVER
(SS-TSLF1H,
SA-TSLF1H,
SS-TSLF1HW)
PARTS LIST
1-479-753-11 REMOTE COMMANDER (RM-ADP011)
1-501-807-12 ANTENNA (FM) (EXCEPT US, CND)
1-501-807-12 ANTENNA (FM) (EXCEPT US, CND)
0
1-569-008-21 ADAPTOR, CONVERSION (E41)
1-754-059-12 ANTENNA, LOOP (AM)
1-754-147-41 ANTENNA (FM) (US, CND)
1-754-059-12 ANTENNA, LOOP (AM)
1-754-147-41 ANTENNA (FM) (US, CND)
1-769-108-11 CORD, CONNECTION (YELLOW:1.5m)
(VIDEO)(EXCEPT AEP, UK, RU)
0
1-770-019-61 ADAPTOR, CONVERSION PLUG (UK, EA3, HK)
1-832-445-11 CORD (WITH CONNECTOR) (SPEAKER)
1-832-445-11 CORD (WITH CONNECTOR) (SPEAKER)
(GREEN:3.5m/ WHITE, RED:5m/ GRAY:10m)
2-687-406-11 MANUAL, INSTRUCTION (ENGLISH)(US, CND)
2-687-406-21 MANUAL, INSTRUCTION (ENGLISH)(AEP, UK)
2-687-406-21 MANUAL, INSTRUCTION (ENGLISH)(AEP, UK)
2-687-406-31 MANUAL, INSTRUCTION
(FRENCH, GERMAN, ITALIAN, DUTCH)(AEP)
2-687-406-41 MANUAL, INSTRUCTION
(SPANISH, POLISH, SWEDISH)(AEP)
2-687-406-51 MANUAL, INSTRUCTION (RUSSIAN)(RU)
2-687-406-61 MANUAL, INSTRUCTION (ENGLISH)
2-687-406-61 MANUAL, INSTRUCTION (ENGLISH)
(TW, SP, EA3, HK, E41, AUS)
2-687-406-71 MANUAL, INSTRUCTION (FRENCH, SPANISH)
(MX, SP, EA3, E41)
2-687-406-81 MANUAL, INSTRUCTION (FRENCH) (CND)
2-687-406-91 MANUAL, INSTRUCTION (ARABIC) (EA3)
2-687-407-11 MANUAL, INSTRUCTION
2-687-406-91 MANUAL, INSTRUCTION (ARABIC) (EA3)
2-687-407-11 MANUAL, INSTRUCTION
(TRADITIONAL CHINESE) (TW, SP, HK)
2-687-407-21 MANUAL, INSTRUCTION (KOREAN) (KR)
2-687-407-31 MANUAL, INSTRUCTION
2-687-407-31 MANUAL, INSTRUCTION
(SIMPLIFIED CHINESE) (CH)
2-687-448-11 MANUAL, INSTRUCTION
(DANISH, FINNISH) (AEP)
2-687-448-21 MANUAL, INSTRUCTION (PORTUGUESE) (AEP)
2-687-448-31 MANUAL, INSTRUCTION (GREEK) (AEP)
2-687-448-41 MANUAL, INSTRUCTION
2-687-448-31 MANUAL, INSTRUCTION (GREEK) (AEP)
2-687-448-41 MANUAL, INSTRUCTION
(CZECH, HUNGARIAN)(AEP)
2-687-448-51 MANUAL, INSTRUCTION (TURKISH) (AEP)
2-687-448-61 MANUAL, INSTRUCTION (SLOVAK) (AEP)
2-890-349-01 COVER (REMOTE CONTROL)
2-890-349-01 COVER (REMOTE CONTROL)
1
A-1071-985-A IR RECEIVER (DIR-R3)
2
A-4718-204-A IR TRANSMITTER (DIR-T1)
3
1-542-644-11 MEASUREMENT MIC (STEREO)
(Calibration mic)
4
2-675-790-01 PANEL (AL-STAND)
5
2-675-791-01 BRACKET (STAND)
6
4-225-252-01 CUSHION (FOOT)
7
4-240-123-01 SCREW (4X12)
8
A-1183-454-A COVER (STAND) ASSY
(Control unit stand cover)
9
3-703-685-21 SCREW (+BV 3X8) (black, small)
10
2-678-887-01 JOINT, CENTER (Adjuster)
11
2-678-927-01 CUSHION, JOINT (for Adjuster)
12
2-678-888-01 STAND, CENTER (Center speaker base)
13
4-255-545-01 FOOT (for Center speaker base)
14
7-682-580-04 SCREW +B 5X25 (silver, large)
15
A-1182-059-A POLE ASSY (Post)
16
A-1182-060-A BASE ASSY (Base)
17
A-1182-058-A BRACKET ASSY
(Speaker adaptor/Speaker adaptor cover)
18
2-678-898-01 CLAMP, CORD
19
2-048-751-01 SCREW +BVTP 3.5X14 TYPE2 (black, medium)
20
7-682-576-04 SCREW +B 5X12 (silver, small)
21
7-682-565-09 SCREW +B 4X16 (black, large)
22
2-678-862-01 DECORATION, BASE
23
2-678-892-01 COVER, BASE
24
2-678-905-01 BASE
25
4-251-067-01 PACKING (AL FRONT)
Ref. No.
Part No.
Description
Remark
•
Abbreviation
AUS
AUS
: Australian model
CH
: Chinese model
CND : Canadian model
E41
E41
: 230 V AC area in E model
EA3
: Saudi Arabia model
HK
: Hong Kong model
KR
: Korean model
MX
: Mexican model
RU
: Russian model
SP
: Singapore model
TW
: Taiwan model
Ver. 1.2
The components identified by mark 0 or
dotted line with mark 0 are critical for safety.
Replace only with part number specified.
dotted line with mark 0 are critical for safety.
Replace only with part number specified.
Les composants identifiés par une marque 0
sont critiques pour la sécurité.
Ne les remplacer que par une pièce portant le
numéro spécifié.
sont critiques pour la sécurité.
Ne les remplacer que par une pièce portant le
numéro spécifié.
3
DAV-LF1H
ASSEMBLING AND CONNECTING THE SYSTEM
Before connecting, attach the stands to the control unit and the speakers.
Tip
We recommend that you spread a cloth on the floor to avoid damaging the floor when assembling.
Assembling the control unit
Attach the stand to the control unit.
Use the parts illustrated below.
Use the parts illustrated below.
Tip
You can install the control unit on a wall using an optional kit (not supplied).
1
Hook the studs of the control unit on the keyslots of the control unit stand, then secure
the control unit with the screw.
the control unit with the screw.
Control unit (1)
Control unit stand (1)
Control unit stand cover
(1)
Screw (black, small)
(1)
Control unit
Control unit stand
,
SYSTEM CONTROL cord
Hook the SYSTEM CONTROL
cord in the clamp on the control
unit stand.
cord in the clamp on the control
unit stand.
Screw (black, small)
2
Attach the control unit stand cover to the control unit stand.
Snap the control unit stand cover onto the control unit stand.
Control unit stand cover
Control unit stand
,
Draw the SYSTEM CONTROL cord
through the opening of the control unit
stand cover.
through the opening of the control unit
stand cover.
Assembling the speakers
Attach the stands and connect the speaker cords to the center speaker, front speakers, and surround
speakers.
speakers.
About connecting speaker cord
The connector and color tube of the speaker cords are the same color as the label of the speaker to be
connected.
connected.
To avoid short-circuiting the speakers
Short-circuiting of the speakers may damage the system. To prevent this, be sure to follow these
precautions when connecting the speakers. Make sure the bare wire of each speaker cord does not touch
another speaker terminal or the bare wire of another speaker cord, such as shown below.
precautions when connecting the speakers. Make sure the bare wire of each speaker cord does not touch
another speaker terminal or the bare wire of another speaker cord, such as shown below.
Note
Be sure to match the speaker cord to the appropriate terminal on the components: 3 to 3, and # to #. If the cords
are reversed, the sound will lack bass and may be distorted.
To assemble the center speaker
Use the parts illustrated below.
Tip
You can install the center speaker on a wall using an optional kit (not supplied).
Center speaker (1)
Adjuster (1)
Center speaker
base (1)
Speaker cord
(green) (1)
Screws
(silver, large) (2)
Label on the rear of the
speaker: Green
Color tube
(–)
(+)
Gray
Black
Do not catch the
speaker cord insulation
in the SPEAKER jack.
speaker cord insulation
in the SPEAKER jack.
Stripped speaker cord is
touching another speaker
terminal.
touching another speaker
terminal.
Stripped cords are touching each
other due to excessive removal of
insulation.
other due to excessive removal of
insulation.
1
Secure the adjuster and center speaker base with the screws.
To adjust the angle of the center speaker
You can set the angle by adjusting the position of the screws.
Center speaker
Screws (silver, large) (2)
* Adjust the length of
the speaker cord
before securing.
before securing.
m
Center speaker base
Adjuster
Speaker cord
*
(green)
Draw out the speaker cord through the slit on the
center speaker base.
center speaker base.
Insert the projections of
the adjuster into the
holes of the center
speaker.
the adjuster into the
holes of the center
speaker.
Gray
Black
Screws
12
°
ASSEMBLING THE SYSTEM
This section is extracted
from instruction manual.
from instruction manual.
DAV-LF1H
4
To assemble the front and surround speakers
Attach the speaker stands to the front and surround speakers. The procedure of assembling for the
surround speaker (L) (the left surround speaker) is slightly different from the others. (The surround
speaker (L) has the IR receiver.) Any difference in procedure is clearly indicated in the text, for
example, “For the surround speaker (L).”
surround speaker (L) (the left surround speaker) is slightly different from the others. (The surround
speaker (L) has the IR receiver.) Any difference in procedure is clearly indicated in the text, for
example, “For the surround speaker (L).”
Use the parts illustrated below.
1)
The front speakers and surround speaker (R) are identical. To discriminate between the speakers, see the label on
the rear of each speaker.
Front speaker (L) (left front speaker): White label
Front speaker (R) (right front speaker): Red label
Surround speaker (R) (right surround speaker): Gray label
the rear of each speaker.
Front speaker (L) (left front speaker): White label
Front speaker (R) (right front speaker): Red label
Surround speaker (R) (right surround speaker): Gray label
2)
Surround speaker (L) (left surround speaker): Blue label
3)
When unpacking, the speaker adaptor cover is attached to the speaker adaptor.
Tip
You can install the front speakers and the surround speakers on a wall using an optional kit (not supplied).
Front speakers
and surround
speaker (R)
1)
(3)
Surround
speaker (L)
2)
(1)
Post (4)
Base (4)
Speaker
adaptor
3)
(4)
Speaker
adaptor cover
3)
(4)
Speaker cords
(3) (white, red,
(3) (white, red,
gray)
Cord clamp (1)
Screws
silver, small (8)
black, large (12)
black, medium (1)
IR
receiver
receiver
Fully-assembled illustration
The speaker that has the IR receiver is the surround speaker (L) (left surround speaker), the speaker
that is connected to the surround speaker (L) is the surround speaker (R) (right surround speaker),
and others are the front speakers.
that is connected to the surround speaker (L) is the surround speaker (R) (right surround speaker),
and others are the front speakers.
1
Insert the post into the base, and secure the base with screws. (for all speakers)
* Do not remove the screw that is attached to the post. The screw is to prevent the speaker from slipping.
IR receiver
Front speaker (L): White label
Front speaker (R): Red label
Front speaker (R): Red label
Surround speaker (R):
Gray label
Gray label
Speaker
system cord
system cord
White
Red
Surround speaker (L):
Blue label
Blue label
Base
Post
Post cover
(upper part)
,
Screws (black, large) (3)
Bottom of the base
Cord clamp
For the surround
speaker (L)
speaker (L)
Screw (black, medium)
Screw
*
Secure the cord clamp
with the screw.
with the screw.
4
(For the surround speaker (L))
Draw the speaker cord first, then draw the speaker system cord into the post.
Draw the speaker cord first, then draw the speaker system cord into the post.
Tip
Tilt the post so that the cords are drawn smoothly.
For the next procedure of the surround speaker (L), skip to step 7.
Speaker cord
Post
Speaker system cord
,
Fold back the speaker cord
about 100 mm and twist
together.
After drawing through, untwist
and straighten out the speaker
cord.
about 100 mm and twist
together.
After drawing through, untwist
and straighten out the speaker
cord.
Post
Speaker system
cord
cord
Hook the speaker
cord and speaker
system cord in the
cord clamp.
cord and speaker
system cord in the
cord clamp.
Bottom of the base
2
Remove the post cover, slide the speaker adaptor onto the post, adjust the height of the
speaker adapter, and secure it with the screws. (for all speakers)
speaker adapter, and secure it with the screws. (for all speakers)
Note
Keep the post cover handy, so you can replace it later.
3
(For the surround speaker (L))
Connect the connector of the speaker cord to the speaker.
Connect the connector of the speaker cord to the speaker.
Screws
Speaker
adaptor
adaptor
,
Post
Hook
(upper part)
(upper part)
,
Post cover
Screws
Loosen (but do
not remove) the
screws before
attaching.
Loosen (but do
not remove) the
screws before
attaching.
About the height of the speaker
The height of the speaker top is A + 390 mm.
(A: Between the top of the speaker adaptor and top of the
base.)
base.)
Lowest position: A = 570 mm, Speaker top = 960 mm
Highest position: A = 910 mm, Speaker top = 1,300 mm
Rear of the surround speaker (L)
Connector (gray)
Speaker cord