DAV-FXG9K, HCD-FXG9K - Sony Audio Service Manual (repair manual). Page 2

2

COMPONENTS  IDENTIFIED  BY  MARK  0  OR  DOTTED  LINE
WITH  MARK  0  ON  THE  SCHEMATIC  DIAGRAMS  AND  IN
THE  PARTS  LIST  ARE  CRITICAL  TO  SAFE  OPERATION.
REPLACE  THESE  COMPONENTS  WITH  SONY  PARTS  WHOSE
PART  NUMBERS  APPEAR  AS  SHOWN  IN  THIS  MANUAL  OR
IN  SUPPLEMENTS  PUBLISHED  BY  SONY.

Video section
Outputs

VIDEO: 1 Vp-p 75 ohms
S VIDEO:
Y: 1 Vp-p 75 ohms
C: 0.286 Vp-p 75 ohms
COMPONENT:
Y: 1 Vp-p 75 ohms
P

B

/C

B

, P

R

/C

R

: 0.7 Vp-p

75 ohms
HDMI OUT: Type A (19 pin)

Inputs

VIDEO: 1 Vp-p 75 ohms
COMPONENT:
Y: 1 Vp-p 75 ohms
P

B

/C

B

, P

R

/C

R

: 0.7 Vp-p

75 ohms

General
Power requirements

220 - 240 V AC, 50/60 Hz

Power consumption

On: 210 W
Standby: 0.3 W (at the
Power Saving Mode)

Dimensions (approx.)

445 

× 71 × 405 mm (w/h/d)

incl. projecting parts

Mass (approx.)

6.0 kg

CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous radiation
exposure.

UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with

the lead free mark due to their particular size)

Unleaded solder has the following characteristics.

• Unleaded solder melts at a temperature about 40 °C higher

than ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350 

°C.

Caution: The printed pattern (copper foil) may peel away if

the heated tip is applied for too long, so be careful!

• Strong viscosity

Unleaded solder is more viscou-s (sticky, less prone to flow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.

• Usable with ordinary solder

It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.

• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be

damaged by heat.

• Keep  the temperature of the soldering iron around 270 °C

during repairing.

• Do not touch the soldering iron on the same conductor of the

circuit board (within 3 times).

• Be careful not to apply force on the conductor when soldering

or unsoldering.

This appliance is
classified as a CLASS 1
LASER product. This
marking is located on the
rear of the unit.

– Back Panel –

• Abbreviation

E3

: AC 240 V area in E model

AUS : Australian model
RU : Russia model
KR : Korea model
SP

: Singapore model

TH : Thai model

Parts No.

KR, SP, TH model

2-682-126-0s

AUS model

2-682-126-2s

E3 model

2-682-126-3s

RU model

2-682-126-4s