Read Sony DAV-DZ360WA / DAV-DZ361W / HCD-DZ360WA / HCD-DZ361W Service Manual online
SERVICE MANUAL
Sony Corporation
Audio&Video Business Group
Published by Sony Techno Create Corporation
HCD-DZ360WA/DZ361W
DVD RECEIVER
9-889-184-01
2008G04-1
©
2008.07
AEP Model
HCD-DZ360WA
UK Model
HCD-DZ360WA/DZ361W
• HCD-DZ360WA/DZ361W are the amplifi er, DVD/CD and
tuner section in DAV-DZ360WA/DZ361W.
Model Name Using Similar Mechanism
HCD-DZ260/DZ270/HDZ278
Mechanism Type
CDM85-DVBU102
Optical Pick-up Name
KHM-313CAA
This system incorporates with Dolby* Digital and Dolby Pro
Logic (II) adaptive matrix surround decoder and the DTS** Digital
Surround System.
* Manufactured under license from Dolby Laboratories.
Logic (II) adaptive matrix surround decoder and the DTS** Digital
Surround System.
* Manufactured under license from Dolby Laboratories.
“Dolby”, “Pro Logic”, and the double-D symbol are trademarks
of Dolby Laboratories.
of Dolby Laboratories.
** Manufactured under license from DTS, Inc.
“DTS” and “DTS Digital Surround” are registered trademarks
of DTS, Inc.
of DTS, Inc.
SPECIFICATIONS
Amplifi er Section
Stereo mode (rated)
108 W + 108 W (at 3 ohms,
1 kHz, 1% THD)
Surround mode (reference) RMS output power
FL/FR/C/SL/SR*:
FL/FR/C/SL/SR*:
142
watts (per channel at 3
ohms, 1 kHz, 10% THD)
Subwoofer*: 140 watts (at
3 ohms, 80 Hz, 10% THD)
* Depending on the decoding mode settings and the
source, there may be no sound output.
source, there may be no sound output.
Inputs (Analog)
TV (AUDIO IN)
TV (AUDIO IN)
Sensitivity: 450/250 mV
AUDIO IN
Sensitivity: 250/125 mV
Inputs (Digital)
TV (COAXIAL IN/OPTICAL IN)
TV (COAXIAL IN/OPTICAL IN)
Impedance: 75 ohms/-
Outputs (Analog)
Phones
Phones
Accepts low- and high-
impedance
headphones.
Super Audio CD/DVD System
Laser Semiconductor
laser
(Super
Audio
CD/DVD:
λ
= 650 nm)
(CD:
λ = 790 nm)
Emission
duration:
continuous
Signal format system
Signal format system
PAL/NTSC
USB Section
Supported bit rate
MP3 (MPEG 1 Audio Layer-3):
MP3 (MPEG 1 Audio Layer-3):
32 kbps - 320 kbps
WMA:
48 kbps - 192 kbps
AAC:
48 kbps - 320 kbps
Sampling frequencies
MP3 (MPEG 1 Audio Layer-3):
32/44.1/48
MP3 (MPEG 1 Audio Layer-3):
32/44.1/48
kHz
WMA: 44.1
kHz
AAC: 44.1
kHz
(USB) port:
Maximum current:
500 mA
Tuner Section
System
PLL quartz-locked digital
synthesizer
FM tuner section
Tuning range
FM tuner section
Tuning range
87.5 MHz - 108.0 MHz (50
kHz
step)
Antenna (aerial)
FM wire antenna (aerial)
Antenna (aerial) terminals 75 ohms, unbalanced
Intermediate frequency
Intermediate frequency
10.7 MHz
AM tuner section
Tuning range
Tuning range
531 kHz - 1,602 kHz (with
the interval set at 9 kHz)
Antenna (aerial)
AM loop antenna (aerial)
Intermediate frequency
450 kHz
Video Section
Outputs
VIDEO: 1 Vp-p 75 ohms
R/G/B: 0.7 Vp-p 75 ohms
HDMI OUT: Type A (19
pin)
– Continued on next page –
Ver. 1.0 2008.07
HCD-DZ360WA/DZ361W
2
SAFETY-RELATED COMPONET WARNING!
COMPONENTS IDENTIFIED BY MARK
0 OR DOTTED LINE
WITH MARK
0 ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS
REPLACE THESE COMPONENTS WITH SONY PARTS
WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS
MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
SPECIAL COMPONENT NOTICE
The components identifi ed by mark
The components identifi ed by mark
9 contain confi dential infor-
mation.
Strictly follow the instructions whenever the components are re-
paired and/or replaced.
Strictly follow the instructions whenever the components are re-
paired and/or replaced.
Model
Part No.
DZ360WA
3-273-765-9[]
DZ361W
3-875-160-3[]
MODEL IDENTIFICATION
– Back Panel –
– Back Panel –
General
Power requirements
220 V - 240 V AC, 50/60 Hz
Power consumption
DAV-DZ360WA: On:
DAV-DZ360WA: On:
170
W
Standby: 0.3 W (at the
Power Saving mode)
DAV-DZ361W: On:
125
W
Standby: 0.3 W (at the
Power Saving mode)
Output voltage (DIGITAL MEDIA PORT)
DC
DC
5
V
Output current (DIGITAL MEDIA PORT)
700
700
mA
Dimensions (approx.)
430 mm
× 66 mm × 385 mm
(w/h/d) incl. projecting parts
430
mm
× 66 mm × 415 mm
(w/h/d) with the wireless transceiver
inserted
Mass (approx.)
Mass (approx.)
4.2 kg
Design and specifi cations are subject to change
without notice.
without notice.
Parts No.
HCD-DZ360WA/DZ361W
3
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40 °C higher
• Unleaded solder melts at a temperature about 40 °C higher
than ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350 °C.
Caution: The printed pattern (copper foil) may peel away if
about 350 °C.
Caution: The printed pattern (copper foil) may peel away if
the heated tip is applied for too long, so be careful!
• Strong
viscosity
Unleaded solder is more viscous (sticky, less prone to fl ow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
also be added to ordinary solder.
NOTES ON CHIP COMPONENT REPLACEMENT
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be dam-
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be dam-
aged by heat.
FLEXIBLE CIRCUIT BOARD REPAIRING
• Keep the temperature of soldering iron around 270 °C during
• Keep the temperature of soldering iron around 270 °C during
repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.
Laser component in this product is capable of emitting radiation
exceeding the limit for Class 1.
exceeding the limit for Class 1.
This appliance is classifi ed as
a CLASS 1 LASER product.
This marking is located on the
rear or bottom exterior.
a CLASS 1 LASER product.
This marking is located on the
rear or bottom exterior.
CAUTION
Use of controls or adjustments or performance of procedures
other than those specifi ed herein may result in hazardous radia-
tion exposure.
Use of controls or adjustments or performance of procedures
other than those specifi ed herein may result in hazardous radia-
tion exposure.
About This Operating
Instructions
• The instructions in this Operating Instructions
describe the controls on the remote. You can
also use the controls on the unit if they have the
same or similar names as those on the remote.
also use the controls on the unit if they have the
same or similar names as those on the remote.
• The Control Menu items may vary depending
on the area.
• “DVD” may be used as a general term for a
DVD VIDEO, DVD+RW/DVD+R, and DVD-
RW/DVD-R.
RW/DVD-R.
• Measurements are expressed in feet (ft) for
North American models.
• The default setting is underlined.
About the S-AIR function
The system is compatible with the S-AIR
function, which allows transmission of sound
between S-AIR products wirelessly.
The following S-AIR products can be used with
the system:
function, which allows transmission of sound
between S-AIR products wirelessly.
The following S-AIR products can be used with
the system:
• Surround amplifier (supplied): You can enjoy
surround speaker sound wirelessly.
• S-AIR receiver (optional): You can enjoy
system sound in another room.
The S-AIR receiver can be purchased as an
option (the S-AIR product lineup differs
depending on the area).
option (the S-AIR product lineup differs
depending on the area).
Notes or instructions for the surround amplifier
or S-AIR receiver in this operating instructions
refer only to when the surround amplifier or
S-AIR receiver is used.
For details on the S-AIR function, see “Using an
S-AIR Product”.
or S-AIR receiver in this operating instructions
refer only to when the surround amplifier or
S-AIR receiver is used.
For details on the S-AIR function, see “Using an
S-AIR Product”.
HCD-DZ360WA/DZ361W
4
5
GB
Playable Discs
1)
MP3 (MPEG1 Audio Layer 3) is a standard format defined by ISO/MPEG which compresses audio data. MP3 files
must be in MPEG1 Audio Layer 3 format.
n
o
c
I
s
c
i
t
s
i
r
e
t
c
a
r
a
h
C
o
g
o
l
c
s
i
D
e
p
y
T
O
E
D
I
V
D
V
D
•
O
E
D
I
V
D
V
D
• DVD-R/DVD-RW in DVD
VIDEO format or video mode
• DVD+R/DVD+RW in DVD
VIDEO format
VR (Video
Recording) mode
Recording) mode
• DVD-R/DVD-RW in VR (Video
Recording) mode (except for
DVD-R DL)
DVD-R DL)
D
C
o
i
d
u
A
r
e
p
u
S
•
D
C
o
i
d
u
A
r
e
p
u
S
)
s
c
s
i
d
0
.
2
d
n
a
1
.
1
.
r
e
V
(
D
C
O
E
D
I
V
•
D
C
O
E
D
I
V
• Super VCD
• CD-R/CD-RW/CD-ROM in video
CD format or Super VCD format
D
C
o
i
d
u
A
•
D
C
• CD-R/CD-RW in audio CD format
n
i
M
O
R
-
D
C
/
W
R
-
D
C
/
R
-
D
C
•
–
D
C
A
T
A
D
DATA CD format, containing MP3
files
files
1)
, JPEG image files
2)
, and
DivX video files
3)4)
, and
conforming to ISO 9660
5)
Level 1/
Level 2, or Joliet (extended format)
/
W
R
-
D
V
D
/
R
-
D
V
D
/
M
O
R
-
D
V
D
•
–
D
V
D
A
T
A
D
DVD+R/DVD+RW in DATA
DVD format, containing MP3
files
DVD format, containing MP3
files
1)
, JPEG image files
2)
, and
DivX video files
3)4)
, and
conforming to UDF (Universal
Disk Format)
Disk Format)
