DAV-DZ10, HCD-DZ10 - Sony Audio Service Manual (repair manual). Page 19

19

Be sure to use the DVD disc that matches the signal standards of
your region.

• 

CD

YEDS-18  (Part No.: 3-702-101-01)
PATD-012 (Part No.: 4-225-203-01)

• DVD SL (Single Layer)

NTSC : HLX-503 (Part No.: J-6090-069-A)

HLX-504 (Part No.: J-6090-088-A)

PAL    : HLX-506 (Part No.: J-6090-077-A)

• DVD DL (Dual Layer)

NTSC : HLX-501 (Part No.: J-6090-071-A)

HLX-505 (Part No.: J-6090-089-A)

PAL    : HLX-507 (Part No.: J-6090-078-A)

The Mirror Time and IOP measurement allows you to make
diagnosis and adjustment simply by using the remote commander
and monitor TV. The instructions, diagnosis results, etc. are given
on the on-screen display (OSD).
Be sure to execute the Mirror Time and IOP measurement when a
BU (Base Unit) is replaced.

While pressing the  

x  

and  A  buttons simultaneously, turn

VOLUME +  with the DVD player in power on.
The Test Mode starts, then the menu shown below will be displayed
on the TV screen.

The menu above is the Remocon Diagnosis Menu screen which
consists of six main function. At the bottom of the menu screen, the
model name and IF-con version. To enter Mirror Time
Adjustment menu, press button  2 “R”  on the remote commander
to enter Drive Manual Operation menu. To exit from the Test Mode,
press the power button on the remote commander.

The Drive Manual Operation menu consists of five main function.
By pressing  2 “R”  button on the remote commander in the Remocon
Diagnosis Menu, the screen will appear as below.

Remocon Diagnosis Menu

0. External Chip Check
1. Servo Parameter Check
2. Drive Manual Operation
3. Emergency History
4. Version Information
5. Video Level Adjustment

Model Name : DSX0_ XX
IF-con

: V

Syscon

: Ver.

er. XX.XX (XXXX)

X.XXX

*

1

*1: Changes depending on destination 

Drive Manual Operation

1. Servo Control
2. Track/Layer Jump
3. Manual Adjustment
4. Tray Aging Mode
5. MIRR time Adjust
0. Return to Top Menu

To enter Mirror Time Adjustment, press  5 “R”  button on the remote
commander. The screen will appear as below.

There are five main commands in the Mirr time Adjust menu as
shown in the figure above. The functions of each command are
described in the following page.

1. CD MIRR time Check
This command checks the Mirror time value for CD disc.

2. DVD MIRR time Check
This command checks the Mirror time value for DVD disc.

3. Threshold
This command displays the threshold value between CD and DVD
mirror time.

4. Save to EEPROM
This command saves an adjusted mirror time value to the EEPROM.

5. Default set MIRR time
This command will set CD and DVD mirror time to firmware default
value.

[Open] / [Close]
Pressing the   A   button controls the tray for disc change during
mirror time adjustment.
[0] Return to previous menu
Press the  0 “R”  button to return to previous menu.

In order to execute mirror time adjustment, the following standard
procedures must be followed.

(1) In power on, while pressing the  

x  

and  A  buttons

simultaneously, turn  VOLUME +  .

(2) Select “2. Drive Manual Operation”.

MIRR time Adjust Menu

1. CD MIRR time Check:
2. DVD MIRR time Check:
3. Threshold:
4. Save to EEPROM
5. Default set MIRR time

[Open] Tray open [Close] Tray close
[0] Return to previous menu

Remocon Diagnosis Menu

0. External Chip Check
1. Servo Parameter Check
2. Drive Manual Operation
3. Emergency History
4. Version information
5. Video Level Adjustment

Model  Name
IF-con

: Ver. XX.XX (XXXX)

Syscon

: Ver. X.XXX

: DSX0_ XX

*

1

*1: Changes depending on destination