CX-LEMV300, XR-EMV300 - Sony Audio Service Manual (repair manual). Page 3

Read Sony CX-LEMV300 / XR-EMV300 Service Manual online

3
CX-LEMV300
SERVICING NOTES
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous
radiation exposure.
The laser diode in the optical pick-up block may suffer electrostatic
break-down because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled with
care.
NOTES  ON  LASER  DIODE  EMISSION  CHECK
The laser beam on this model is concentrated so as to be focused on
the disc reflective surface by the objective lens in the optical pick-
up block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.
LASER  DIODE  AND  FOCUS  SEARCH  OPERATION
CHECK
Carry out the “S curve check” in “CD section adjustment” and check
that the S curve waveforms is output three times.
NOTES  ON  HANDLING  THE  OPTICAL  PICK-UP
BLOCK  OR  BASE  UNIT
Notes on chip component replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be dam-
aged by heat.
Flexible Circuit Board Repairing
• Keep the temperature of the soldering iron around 270 ˚C during
repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering or
unsoldering.
Unleaded solder
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size.)
 : LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40
°C higher than
ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350
°C.
Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!
• Strong viscosity
Unleaded solder is more viscous (sticky, less prone to flow) than
ordinary solder so use caution not to let solder bridges occur such
as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 
0
 OR DOTTED LINE WITH
MARK 
0
 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS
LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.
ADVERSEL: 
USYNLIG LASERSTRÅLING NÅR DEKSEL ÅPNES OG 
SIKKERHEDSLÅS BRYTES. UNNGÅ EKSPONERING FOR STRÅLEN.
CAUTION:
INVISIBLE LASER RADIATION WHEN OPEN AND INTERLOCKS 
DEFEATED. AVOID EXPOSURE TO BEAN.
ADVARSEL:
USYNLIG LASERSTRÅLING VED ÅBNING NÅR 
SIKKERHEDSAFBRYDERE ER UDE AF FUNKTION. UNDGÅ UDSAETTELSE FOR 
STRÅLING.
VORSICHT:
UNSICHTBARE LASERSTRAHLUNG. WENN ABDECKUNG GEÖFFNET 
UND SICHEREITSVERRIEGELUNG ÜBERBRÜCKT. NICHT DEM STRAHL 
AUSSETZENSTRÅLING.    
VARO!: 
AVATTAESSA JA SUOJALUKITUS OHITETTAESSA OLET ALT-TIINA 
NÄKYMÄTTÖMÄLLE LASERSÄTEILYLLE. ÄLÄ KÄTSO SÄTEESEEN.
VARNING: 
OSYNLIG LASERSTRÅLING NÄR DENNA DEL ÄR ÖPPNAD OCH 
SPÄRREN ÄR URKOPPLAD. BETRAKTA EJ STRÅLEN.
VIGYÁZAT!: 
A BURKOLAT NYITÁSAKOR LÁTHATATLAN LÉZERSU-GÁRVESZÉLY! 
KERÜLJE A BESUGÁRZÁST!
To prevent fire or shock hazard, do not expose the
unit to rain or moisture.
To avoid electrical shock, do not open the cabinet.
Refer servicing to qualified personnel only.
Do not install the appliance in a confined space, such as
a bookcase or built-in cabinet.
CLASS 1 LASER PRODUCT
LUOKAN 1 LASER LAITE
KLASS 1 LASER APPARAT
This appliance is classified
as a CLASS 1 LASER
product.
This label is located on the
exterior.
To prevent fire, do not cover the ventilation of the apparatus
with newspapers, table-cloths, curtains, etc. And do not
place lighted candles on the apparatus.
To prevent fire or shock hazard, do not place objects filled
with liquids, such as vases, on the apparatus.
Page of 53
Display

Click on the first or last page to see other CX-LEMV300 / XR-EMV300 service manuals if exist.