Read Sony CMT-WS2D / HCD-WS2D Service Manual online
2
HCD-WS2D
MODEL IDENTIFICATION
– Rear Panel –
– Rear Panel –
Model
Part No.
AEP, UK
2-580-682-0
[]
RU
2-580-682-2
[]
SP6
2-580-682-5
[]
E3
2-580-682-6
[]
HK
2-580-682-7
[]
• Abbreviation
E3
: 240 V AC Area in E model.
HK
: Hong Kong model.
RU
: Russian model.
SP6
: Singapore and Malaysia models.
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous radiation
exposure.
other than those specified herein may result in hazardous radiation
exposure.
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
•
Unleaded solder melts at a temperature about 40
°
C higher
than ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350
°
C.
Caution: The printed pattern (copper foil) may peel away if
the heated tip is applied for too long, so be careful!
•
Strong viscosity
Unleaded solder is more viscou-s (sticky, less prone to flow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
Unleaded solder is more viscou-s (sticky, less prone to flow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
•
Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
Notes on chip component replacement
•
Never reuse a disconnected chip component.
•
Notice that the minus side of a tantalum capacitor may be
damaged by heat.
damaged by heat.
Flexible Circuit Board Repairing
•
Keep the temperature of the soldering iron around 270
°
C
during repairing.
•
Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
circuit board (within 3 times).
•
Be careful not to apply force on the conductor when soldering
or unsoldering.
or unsoldering.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK
0
OR DOTTED LINE
WITH MARK
0
ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE
PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR
IN SUPPLEMENTS PUBLISHED BY SONY.
REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE
PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR
IN SUPPLEMENTS PUBLISHED BY SONY.
Laser component in this product is capable of emitting radiation
exceeding the limit for Class 1.
exceeding the limit for Class 1.
This appliance is classified as
a CLASS 1 LASER product.
This markng is located on the
rear exterior.
a CLASS 1 LASER product.
This markng is located on the
rear exterior.
General
Power requirements
European and Russian models:
European and Russian models:
230 V AC, 50/60 Hz
Other models:
120 V or 220 – 240 V AC,
50/60 Hz
Adjustable with voltage
selector
50/60 Hz
Adjustable with voltage
selector
Power consumption
50 watts
0.3 watts (in Power Saving
mode)
0.3 watts (in Power Saving
mode)
Dimensions (w/h/d) (excl. speakers)
Approx. 254.5
×
136
×
346.5 mm
Mass
Approx. 3.4 kg
Design and specifications are subject to change
without notice.
without notice.
Part No.
Click on the first or last page to see other CMT-WS2D / HCD-WS2D service manuals if exist.