Read Sony CMT-PX333 / HCD-PX333 Service Manual online
91
HCD-PX333
Pin No.
Pin Name
I/O
Description
46
MD/CD POWER
O
Power down detection signal output to the MD mechanism controller (IC1001) and CD
mechanism controller (IC1101)
mechanism controller (IC1101)
47
TR RELAY
O
Standby relay (RY991) control signal output (“L”: standby, “H” : power on)
PC LINK/KEY BOARD (CN104) ON/OFF control signal output (“H”: on, “L” : off)
48
RECMUTE
O
Muting on/off control signal output of tape output signal “L”: muting on
49
DIMMER
O
LCD back light on/off control signal output “H”: LED on
50
GC POWER
O
Not used (open)
51
KBD CHK
I
Key board check signal input terminal
52
LED MD-PAUSE
O
LED drive signal output of the X (MD) indicator (D605) “H”: LED on
53
LED MD-PLAY
O
LED drive signal output of the N (MD) indicator (D604) “H”: LED on
54
LED CD-PAUSE
O
LED drive signal output of the X (CD) indicator (D603) “H”: LED on
55
LED CD-PLAY
O
LED drive signal output of the N (CD) indicator (D602) “H”: LED on
56
LED MD-REC
O
LED drive signal output of the REC indicator (D606) “H”: LED on
57
LED STANDBY
O
LED drive signal output of the I/1 indicator (D601) “H”: LED on
58
BVDD
—
Power supply terminal (+5V)
59
BVSS
—
Ground terminal
60
LED DATA
O
Serial data output terminal for LED driver Not used (open)
61
LED CLK
O
Serial data transfer clock signal output terminal for LED driver Not used (open)
62
LED CE1
O
Chip select signal output terminal for LED driver Not used (open)
63
LED CE2
O
Fan motor (M901) drive signal output “H”: fan motor on
64
LED CLEAR
O
Reset signal output terminal for LED driver Not used (open)
65, 66
FUNC1, FUNC2
O
Function selection signal output terminal Not used (open)
67
HEADPHONE IN
I
Headphone in detection signal input “H”: headphone in
68
ENC VOL A
I
Jog dial pulse input from the rotary encoder A phase input Not used (fixed at “L”)
69
ENC VOL B
I
Jog dial pulse input from the rotary encoder B phase input Not used (fixed at “L”)
70
ENC JOG 1A
I
Jog dial pulse input from the rotary encoder A phase input Not used (fixed at “L”)
71
ENC JOG 1B
I
Jog dial pulse input from the rotary encoder B phase input Not used (fixed at “L”)
72, 73
DEVICE3,
DEVICE2
—
Not used (fixed at “L”)
74
AVDD
—
Power supply terminal (+5V)
75
AVSS
—
Ground terminal
76
AVREF
I
Reference voltage (+5V) input terminal
77, 78
LID SW1,
LID SW2
I
Switch input terminal Not used (fixed at “L”)
79 to 82
DIST 1 to DIST 4
I
Model destination setting terminal
83
LEVEL-L
I
L-ch level input terminal Not used (fixed at “L”)
84
LEVEL-R
I
L-ch level input terminal Not used (fixed at “L”)
85
KEY1
I
Key input terminal (A/D input) S601 to S606 (I/1, x (CD), N X CD, M >,
TUNING +, VOLUME –, VOLUME + keys input)
TUNING +, VOLUME –, VOLUME + keys input)
86
KEY2
I
Key input terminal (A/D input) S621 to S628 (. m TUNING –, FUNCTION,
PLAY MODE TUNING MODE, REPEAT STEREO/MONO, REC MODE, REC/REC IT,
CD SYNC NORMAL, CD SYNC HIGH keys input)
PLAY MODE TUNING MODE, REPEAT STEREO/MONO, REC MODE, REC/REC IT,
CD SYNC NORMAL, CD SYNC HIGH keys input)
87
KEY3
I
Key input terminal (A/D input) S631 to S637 (Z MD, x (MD), . m, N X MD,
M >, Z CD, TUNER/BAND keys input)
M >, Z CD, TUNER/BAND keys input)
88
KEY4
I
Key input terminal (A/D input) Not used (fixed at “H”)
89
NMI
I
Non-maskable interrupt input terminal Fixed at “L” in this set
90
KBD CLK
I
Key board data reading clock signal input terminal
91
KEY RM INT
I
Interrupt signal input from function keys or remote control receiver
Click on the first or last page to see other CMT-PX333 / HCD-PX333 service manuals if exist.