Read Sony CMT-DF1 / HCD-DF1 Service Manual online
2
HCD-DF1
TABLE OF CONTENTS
1.
SERVICING NOTES
...............................................
3
2.
GENERAL
...................................................................
5
3.
DISASSEMBLY
3-1.
Disassembly Flow ...........................................................
6
3-2.
Panel Left, Panel Right ....................................................
6
3-3.
Cabinet Rear Block .........................................................
7
3-4.
Cabinet Front Block ........................................................
7
3-5.
Mech Deck (H-21), DECK Board ...................................
8
3-6.
MAIN Board ....................................................................
8
3-7.
OP Assy (KHM-313AHC) ..............................................
9
4.
TEST MODE
.............................................................. 10
5.
MECHANICAL ADJUSTMENTS
....................... 10
6.
ELECTRICAL ADJUSTMENT
............................ 11
7.
DIAGRAMS
7-1.
Block Diagram – MAIN Section – .................................. 13
7-2.
Block Diagram
– PANEL/POWER SUPPLY Section – ........................... 14
– PANEL/POWER SUPPLY Section – ........................... 14
7-3.
Printed Wiring Board – DECK Board – .......................... 16
7-4.
Schematic Diagram – DECK Board – ............................. 17
7-5.
Printed Wiring Board – MICROPHONE Board – ........... 18
7-6.
Schematic Diagram – MICROPHONE Board – ............. 18
7-7.
Printed Wiring Board – MAIN Board – .......................... 19
7-8.
Schematic Diagram – MAIN Board (1/4) – .................... 20
7-9.
Schematic Diagram – MAIN Board (2/4) – .................... 21
7-10. Schematic Diagram – MAIN Board (3/4) – .................... 22
7-11. Schematic Diagram – MAIN Board (4/4) – .................... 23
7-12. Printed Wiring Board – PANEL Board – ........................ 24
7-13. Schematic Diagram – PANEL Board – ........................... 25
7-14. Printed Wiring Boards – POWER SUPPLY Section – .... 26
7-15. Schematic Diagram – POWER SUPPLY Section – ........ 27
7-11. Schematic Diagram – MAIN Board (4/4) – .................... 23
7-12. Printed Wiring Board – PANEL Board – ........................ 24
7-13. Schematic Diagram – PANEL Board – ........................... 25
7-14. Printed Wiring Boards – POWER SUPPLY Section – .... 26
7-15. Schematic Diagram – POWER SUPPLY Section – ........ 27
8.
EXPLODED VIEWS
8-1.
PANEL Section ............................................................... 31
8-2.
PANEL Board Section ..................................................... 32
8-3.
Tape Deck Section ........................................................... 33
8-4.
DVD Section ................................................................... 34
8-5.
Cabinet Rear Section ....................................................... 35
9.
ELECTRICAL PARTS LIST
................................ 36
Notes on chip component replacement
•
Never reuse a disconnected chip component.
•
Notice that the minus side of a tantalum capacitor may be
damaged by heat.
Flexible Circuit Board Repairing
•
Keep the temperature of the soldering iron around 270 ˚C
during repairing.
•
Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
•
Be careful not to apply force on the conductor when soldering
or unsoldering.
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous radiation
exposure.
other than those specified herein may result in hazardous radiation
exposure.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK
0
OR DOTTED LINE
WITH MARK
0
ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE
PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR
IN SUPPLEMENTS PUBLISHED BY SONY.
REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE
PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR
IN SUPPLEMENTS PUBLISHED BY SONY.
Frequency response
DVD (PCM 48 kHz):
2 Hz
2 Hz
−
22 kHz (
±
1 dB)
CD: 2 Hz
−
20 kHz (
±
1 dB)
Tape deck section
Recording system
4-track 2-channel stereo
Tuner section
FM stereo, FM/AM superheterodyne tuner
FM tuner section
Tuning range
87.5
−
108.0 MHz (50 kHz step)
Antenna
FM lead antenna
Antenna terminals
75 ohms unbalanced
Intermediate frequency
10.7 MHz
AM tuner section
Tuning range
Canadian model:
Canadian model:
530
−
1,710 kHz
Other models:
531
−
1,602 kHz
Antenna
AM loop antenna
Antenna terminals
External antenna terminal
Intermediate frequency
450 kHz
General
Power requirements
European and Russian models:
European and Russian models:
230 V AC, 50/60 Hz
Australian model:
230
−
240 V AC, 50/60 Hz
Korean model:
220 V AC, 60 Hz
Taiwan model:
120 V AC, 50/60 Hz
Other models:
120 V, 220 V, 230
−
240V
AC, 50/60 Hz
Adjustable with voltage selector
Adjustable with voltage selector
Power consumption:
30 watts
Dimensions (w/h/d) (excl. speakers):
Approx. 169
×
218
×
201 mm
Mass (excl. speakers)
Approx. 2.6 kg
Design and specifications are subject to change
without notice.
without notice.
This appliance is
classified as a CLASS 1
LASER product. This
marking is located on the
rear exterior.
classified as a CLASS 1
LASER product. This
marking is located on the
rear exterior.
Click on the first or last page to see other CMT-DF1 / HCD-DF1 service manuals if exist.