Read Sony CMT-CP11 / CMT-CP11K / HCD-CP11 Service Manual online
29
Pin No.
Pin Name
I/O
Description
30
RDS-ON
O
Power supply on/off control signal output of the tuner pack (+7.5V) and RDS decoder (IC804)
(RDS decoder: used for the AEP and UK models only)
LED drive signal output of the TUNER indicator (D855) “H”: tuner power on (LED on)
(RDS decoder: used for the AEP and UK models only)
LED drive signal output of the TUNER indicator (D855) “H”: tuner power on (LED on)
31
HP-CHK
I
Headphone check detection signal input terminal
32
TC-SW
I
Half detect (side A and B) switch and cassette in detect switch input terminal (A/D input)
33
TRAY-SW
I
Disc tray position detect switch (S901, 902) input terminal (A/D input)
“L”: close position, “M”: open position, “H”: moving
“L”: close position, “M”: open position, “H”: moving
34
KEY3
I
Key input terminal (A/D input) S817 to S822, S824 and S825 (STANDBY I/
u, CD, TUNER,
TAPE, MD/VIDEO, DSG, TUNER BAND, CD SYNC keys input)
35
KEY2
I
Key input terminal (A/D input) S801 to S808 (TUNING MODE, CD
^/p/+/=, PLAY
MODE, REPEAT, CD EJECT
6 keys input)
36
KEY1
I
Key input terminal (A/D input)
S809 to S816 (TAPE
S809 to S816 (TAPE
9 (/p/)/0/P, REC r, TUNING +/– keys input)
37
SIMUKE
I
Destination setting terminal (A/D input)
38
RESET
I
System reset signal input from the reset signal generator (IC803) “L”: reset
For several hundreds msec. after the power supply rises, “L” is input, then it changes to “H”
For several hundreds msec. after the power supply rises, “L” is input, then it changes to “H”
39
EXTAL1
I
Main system clock input terminal (4.19 MHz)
40
XTAL1
O
Main system clock output terminal (4.19 MHz)
41
VSS
—
Ground terminal
42
XTAL2
O
Sub system clock output terminal (500 kHz) Not used (open)
43
EXTAL2
I
Sub system clock input terminal (500 kHz) Not used (fixed at “L”)
44
AVREF
I
Reference voltage (+5V) input terminal (for A/D conversion)
45
AVSS
—
Ground terminal (for A/D conversion)
46
VL
O
Liquid crystal display bias on/off control signal output terminal
47 to 49
VLC3 to VLC1
—
Power supply terminal for the liquid crystal display bias
50 to 53
COM0 to COM3
O
Common drive signal output to the liquid crystal display (LCD801)
54 to 85
SEG0 to SEG31
O
Segment drive signal output to the liquid crystal display (LCD801)
86
REC-BIAS
O
Recording bias on/off selection signal output to the HA12203NT (IC352)
“L”: bias on, “H”: bias off
“L”: bias on, “H”: bias off
87
REC-MUTE
O
Recording muting on/off selection signal output to the HA12203NT (IC352)
“L”: muting on, “H”: muting off
“L”: muting on, “H”: muting off
88
DOLBY
O
Dolby NR on/off selection signal output to the HA12203NT (IC352)
“L”: dolby on, “H”: dolby off
“L”: dolby on, “H”: dolby off
89
VDD
—
Power supply terminal (+5V)
90
NC
—
Connected to power supply (+5V)
91
VSS
—
Ground terminal
92
TX
O
Sub system clock output terminal (32.768 kHz)
93
TEX
I
Sub system clock input terminal (32.768 kHz)
94
CD-ON
O
Power supply on/off control signal output of the CD block (+5V)
LED drive signal output of the CD indicator (D852) “H”: CD power on (LED on)
LED drive signal output of the CD indicator (D852) “H”: CD power on (LED on)
95
REC/PB
O
Recording/playback selection signal output to the BA3126N (IC350) and HA12203NT (IC352)
“L”: playback mode, “H”: recording mode
“L”: playback mode, “H”: recording mode
96
L-MUTE
O
Line muting on/off selection signal output to the HA12203NT (IC352)
“L”: muting on, “H”: muting off
“L”: muting on, “H”: muting off
97
LINE OUT-MUTE
O
Muting on/off control signal output terminal “H”: muting on
98
TC-ON
O
Power supply on/off control signal output of the cassette holder back light
LED drive signal output of the TAPE indicator (D854) “H”: back light on (LED on)
LED drive signal output of the TAPE indicator (D854) “H”: back light on (LED on)
99
WP
I
Wakeup control signal input terminal
100
CD-SCOR
I
Subcode sync (S0+S1) detection signal input from DSP on the CD block (at CD function)
Click on the first or last page to see other CMT-CP11 / CMT-CP11K / HCD-CP11 service manuals if exist.