CMT-C5, HCD-C5 - Sony Audio Service Manual (repair manual). Page 37

Read Sony CMT-C5 / HCD-C5 Service Manual online

37
HCD-C5
5. USING THE CONTINUOUSLY RECORDED DISC
* This disc is used in focus bias adjustment and error rate check.
The following describes how to create a continuous recording
disc.
1. Insert a disc (blank disc) commercially available.
2. Press the  . 
“R”
  or  >
 “R”
   button and display “CREC 1MODE”
(C35).
3. Press the  
ENTER/YES “R”  
button again to display “CREC 1
MID”.
Display “CREC 1(0300)” and start to recording.
4. Complete recording within 5 minutes.
5. Press the  
MENU/NO “R”
  button and stop recording .
6. Press the  
MD 
Z  button and remove the disc.
The above has been how to create a continuous recorded data for
the focus bias adjustment and error rate check.
Note:
 Be careful not to apply vibration during continuous recording.
6. CHECKS PRIOR TO REPAIRS
These checks are performed before replacing parts according to
“approximate specifications” to determine the faulty locations. For
details, refer to “Checks Prior to Parts Replacement and Adjustments
in MD” (see page 30).
6-1. Temperature Compensation Offset Check
When performing adjustments, set the internal temperature and room
temperature to 22 to 28ºC.
Procedure:
1. Press the  
“R”
  or  
“R”
  button to display “TEMP
CHECK” (C12).
2. Press the  
ENTER/YES “R”
  
button.
3. “T=@@(##) [OK]” should be displayed. If “T=@@ (##) [NG]”
is displayed, it means that the results are bad.
(@@ indicates the current value set, and ## indicates the value
written in the non-volatile memory.)
6-2. Laser Power Check
Before starting adjustment;
The laser power adjustment value changes depending upon the types
of the optical pick-up (KMS-260B or KMS-260E).
Check the type of the optical pick-up before starting adjustment.
(See the illustrations “The method of identifying the optical pick-
up” on page 41)
Before checking, check the Iop value of the optical pick-up.
(Refer to 8. Recording and Displaying the Iop Information (see page
40))
Connection:
Procedure:
1. Set the laser power meter on the objective lens of the optical
pick-up. (When it cannot be set properly, press the  m
 “R”
  button
or  M 
“R”
  button to move the optical pick-up.)
Connect the digital volt meter to CN105 pin 1 (I+3V) and
CN105 pin 2 (IOP).
2. Then, press the  
“R”
  or  
“R”
  button and display
“LDPWR CHECK” (C13).
3. Press the  
ENTER/YES “R”
  
button once and display “LD 0.9mW$
  ”. Check that the reading of the laser power meter becomes
specified value.
4. Press the
ENTER/YES “R”
button once more and display “ LD
7.0mW$    ”. Check that the reading the laser power meter and
digital volt meter satisfy the specified value.
Specified Value:
Laser power meter reading :
Digital voltmeter reading : Optical pick-up displayed value 
±
 10%
5. Press the  
MENU/NO  “R”
  button and display “LDPWR
CHECK” (C13) and stop the laser emission.
(The  
MENU/NO “R”
  button is effective at all times to stop the
laser emission.)
Note:
After step 4, each time the  
ENTER/YES “R”  
button is pressed, the
display will be switched to “LD 0.7W$    ”and “LD 6.2mW$    ”
“LD WP 
 $    ”. Nothing needs to be performed here.
Checking Location: BD (MD) board (see page 44)
6-3. Iop Compare
The current Iop value at laser power 7.0 mW output and reference
Iop value (set at shipment) written in the nonvolatile memory are
compared, and the rate of increase/decrease will be displayed in
percentage.
Note:
Perform this function with the optical pick-up set at room tempera-
ture.
Procedure:
1. Press the  . 
“R”
  or  >
 “R”
  button to display “Iop Compare”
(C27).
2. Press the  
ENTER/YES “R”  
button and start measurements.
3. When measurements complete, the display changes to “
±
 xx%
yy”.
xx is the percentage of increase/decrease, and OK or NG is
displayed at yy to indicate whether the percentage of increase/
decrease is within the allowable range.
4. Press the  
MENU/NO “R”
  button to end.
Optical pick-up
objective lens
laser
power meter
+
BD (MD) board
digital voltmeter
CN105 pin 
1
 (I+3V)
CN105 pin 
2
 (IOP)
KMS260B
20101
H0576
lOP = 57.6 mA in this case
lOP (mA) = Digital voltmeter reading (mV)/1 (
)
(Optical pick-up label)
For details of the method for
checking this value, refer to 
“8. Recording and Displaying
the Iop Information”
SPECIFIED VALUE
KMS-260B
KMS-260E
0.85 to 0.91 mW
0.90 to 0.96 mW
KMS-260B
KMS-260E
7.0 to 0.2 mW
7.25 to 0.25 mW
Page of 97
Display

Click on the first or last page to see other CMT-C5 / HCD-C5 service manuals if exist.