Read Sony CFM-S1MK2 Service Manual online
CFM-S1MK2
SERVICE MANUAL
RADIO CASSETTE-CORDER
SPECIFICATIONS
E Model
Model Name Using Similar Machanism
NEW
Tape Transport Mechanism Type
MF-M20-117
• Frequency range
FM: Saudi Arabia: 87.6 - 107 MHz
Other models: 87.6 - 108 MHz
MW: 530 - 1 605 kHz
SW1: 2.3 - 7 MHz
SW2: 7 - 22 MHz
Other models: 87.6 - 108 MHz
MW: 530 - 1 605 kHz
SW1: 2.3 - 7 MHz
SW2: 7 - 22 MHz
• Aerials FM/SW: Telescopic aerial
MW: Built-in ferrite bar aerial
• Recording system 2-track 1 channel mono
• Frequency response 80 - 8 000 Hz
• Speaker Full range: 12 cm (4
• Frequency response 80 - 8 000 Hz
• Speaker Full range: 12 cm (4
3
/
4
inches) dia., 6
Ω, cone
type (1)
• Outputs Earphones jack
For 8
Ωimpedance earphones
• Maximum power output 1.4 W
• Power requirements 110 - 120, 220 - 240 V AC
• Power requirements 110 - 120, 220 - 240 V AC
selectable, 50/60 Hz
6 V DC, 4 R20 (size D) batteries
6 V DC, 4 R20 (size D) batteries
• Power consumption AC 8 W
• Battery life
• Battery life
FM recording: Sony R20P: approx. 18 h
Sony alkaline LR20: approx. 50 h
Tape playback: Sony R20P: approx. 12 h
Sony alkaline LR20: approx. 30 h
• Dimensions Approx. 287 X 147 X 110 mm (w/h/d)
(11
3
/
8
X 5
7
/
8
X 4
4
/
8
inches) (incl. projecting parts)
• Mass (incl. batteries) Approx. 2 kg (4 lb. 7 oz)
• Supplied accessory Mains lead (1)
• Supplied accessory Mains lead (1)
Design and specifications are subject to change without
notice.
notice.
Ver. 1.2 2005.03
9-874-212-03
2005C02-1
© 2005.03
Sony Corporation
Personal Audio Group
Published by Sony Engineering Corporation
2
CFM-S1MK2
TABLE OF CONTENTS
Specifications ........................................................................... 1
1.
GENERAL
Location and Function of Controls .................................... 2
Location and Function of Controls .................................... 2
2.
DISASSEMBLY
2-1. Cabinet (Front) ASSY ................................................. 3
2-2. MD ASSY ................................................................... 3
2-3. Record/Playback Head (HRP101),
Reel/Capstan Motor (M101),Belt ............................... 3
2-4. Jack Board, Main Board, Fine Tune Board ................ 4
2-5. Battery Terminal Board, Power Board, ...................... 4
2-6. Note on Instalation ...................................................... 5
2-7. Dial Pointer Setting .................................................... 5
2-1. Cabinet (Front) ASSY ................................................. 3
2-2. MD ASSY ................................................................... 3
2-3. Record/Playback Head (HRP101),
Reel/Capstan Motor (M101),Belt ............................... 3
2-4. Jack Board, Main Board, Fine Tune Board ................ 4
2-5. Battery Terminal Board, Power Board, ...................... 4
2-6. Note on Instalation ...................................................... 5
2-7. Dial Pointer Setting .................................................... 5
3.
ADJUSTMENTS
3-1. Mechanical Adjustments ............................................. 6
3-2. Electrical Adjustments ................................................ 6
3-1. Mechanical Adjustments ............................................. 6
3-2. Electrical Adjustments ................................................ 6
4
. DIAGRAMS ...................................................................... 9
4-1. Block Diagrams ......................................................... 11
4-2. Schematic Diagrams -Main Section (1/2) - ............. 12
4-3. Schematic Diagrams -Main Section (2/2) - ............. 13
4-4. Printed Wiring Boards .............................................. 14
4-2. Schematic Diagrams -Main Section (1/2) - ............. 12
4-3. Schematic Diagrams -Main Section (2/2) - ............. 13
4-4. Printed Wiring Boards .............................................. 14
5.
EXPLODED VIEWS
5-1. Front Cabinet Section ............................................... 16
5-2. Rear Cabinet Section ................................................ 17
5-3. Mechanism Deck Section-1(MF-M20-117) ............. 18
5-4. Mechanism Deck Section-2(MF-M20-117) ............. 19
5-1. Front Cabinet Section ............................................... 16
5-2. Rear Cabinet Section ................................................ 17
5-3. Mechanism Deck Section-1(MF-M20-117) ............. 18
5-4. Mechanism Deck Section-2(MF-M20-117) ............. 19
6.
ELECTRICAL PARTS LIST ........................................ 20
SECTION 1
GENERAL
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK ! OR DOTTED LINE WITH
MARK !ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST
ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE
PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN
SUPPLEMENTS PUBLISHED BY SONY.
MARK !ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST
ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE
PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN
SUPPLEMENTS PUBLISHED BY SONY.
TUNING
PAUSE
STOP/EJECT
FF
REW
PLAY
REC
BAND
VOLUME
OPR/BATT
MIC
FINE TUNING
FUNCTION
@
DPB
This section is extracted from
instruction manual.
instruction manual.
Location and Function of Controls
3
CFM-S1MK2
Chassis(B)
1
4
2
Screws
+ BVTP 3X10
+ BVTP 3X10
pointer
Lug
MD ASSY
Rear assy, cabinet
3
Connector
(CNP102)
(CNP102)
Connector
(CNP101)
(CNP101)
SECTION 2
DISASSEMBLY
Note : Follow the disassembly procedure in the numerical order given.
2-1. CABINET (FRONT) ASSY
2-2. MD ASSY
• The equipment can be removed using the following procedure.
Set
Cabinet (front) assy
JACK board, MAIN board,
FINE TUNE board
FINE TUNE board
BATTERY TERMINAL board,
POWER board
POWER board
MD assy
Record/playback head (HRP101),
Reel/capstan motor (M101), Belt
Reel/capstan motor (M101), Belt
4
1
6
Remove solder (two places)
2
Screws + BVTP 3X14
2
Screws + BVTP 3X14
Lid, Battery case
Cabinet(front) ASSY
Rear assy, Cabinet
Claws
5
Press the STOP/EJECT button
3
Microphone
2-3. RECORD/PLAYBACK HEAD (HRP101),
REEL/CAPSTAN MOTOR (M101), BELT
REEL/CAPSTAN MOTOR (M101), BELT
1
Screws Tapping+B
MD ASSY
4
Record/playback
head (HRP101)
head (HRP101)
7
Reel/capstan
motor (M101)
motor (M101)
3
Screws
+ PTT 2X 5
+ PTT 2X 5
6
Screws + P2X 5
8
Belt
5
Lug (T), plate
2
Guide, tape
4
CFM-S1MK2
2-4. JACK BOARD, MAIN BOARD, FINE TUNE BOARD
2-5. BATTERY TERMINAL BOARD, POWER BOARD
0
8
4
4
4
Chassis(A)
MAIN board
9
Screws + BVTP 3X10
3
Screw +BVTP 3X10
7
Claw
Rear assy, Cabinet
FINE TUNE board
1
Knob(FT)
1
Knob(band)
1
Knob(function)
1
Knob(vol)
1
Knob(sound)
6
Screw +BVTP 3X10
JACK board
1
Knob(tune)
Bracket(PWB)
5
Connector (CNP1)
2
Connector (CNP901)
6
2
4
Remove Solder
Rear assy, Cabinet
POWER board
3
Remove solder
BATTERY TERMINAR board
5
Screws + BVTP 3X10
1
Claw