Read Sony CFD-S100L Service Manual online
1
CD
Model Name Using Similar Mechanism CFD-S200L
Section
CD Mechanism Type
KSM-213RDP
Optical Pick-up Name
KSS-213R
TC
Model Name Using Similar Mechanism CFD-S200L
Section Tape Transport Mechanism Type
MF-S200
SERVICE MANUAL
CFD-S100L
CD RADIO CASSETTE-CORDER
CD player section
System
System
Compact disc digital audio system
Laser diode properties
Material: GaAlAs
Wave length: 780 nm
Emission duration: Continuous
Laser output: Less than 44.6
Wave length: 780 nm
Emission duration: Continuous
Laser output: Less than 44.6
µW
(This output is the value measured at a distance of
about 200 mm from the objective lens surface on
the optical pick-up block with 7 mm aperture.)
about 200 mm from the objective lens surface on
the optical pick-up block with 7 mm aperture.)
Spindle speed
200 r/min (rpm) to 500 r/min (rpm) (CLV)
Number of channels
2
Frequency response
20 - 20,000 Hz +1/–2 dB
Wow and flutter
Below measurable limit
Radio section
Frequency range
Frequency range
FM: 87.5 - 108 MHz
MW: 531 - 1,611 kHz (9 kHz step)
MW: 531 - 1,611 kHz (9 kHz step)
530 - 1,610 kHz (10 kHz step)
LW: 153 - 279 kHz
IF
FM: 10.7 MHz
MW/LW: 450 kHz
MW/LW: 450 kHz
Aerials
FM: Telescopic aerial
MW/LW: Built-in ferrite bar aerial
MW/LW: Built-in ferrite bar aerial
SPECIFICATIONS
– Continued on next page –
Cassette-corder section
Recording system
Recording system
4-track 2 channel stereo
Fast winding time
Approx. 120 sec. with Sony cassette C-60
Frequency response
TYPE I (normal): 80 - 10,000 Hz
General
Speaker
Speaker
Full range: 10 cm dia.,
3.2 ohms, cone type (2)
3.2 ohms, cone type (2)
Outputs
Headphones jack (stereo minijack)
For 16 - 68 ohms impedance headphones
For 16 - 68 ohms impedance headphones
Maximum power output
4.6 W
Power requirements
For CD radio cassette-corder:
230 V AC, 50 Hz
9 V DC, 6 size D (R20) batteries
230 V AC, 50 Hz
9 V DC, 6 size D (R20) batteries
Power consumption
AC 20 W
Ver. 1.3 2006.03
9-877-016-04
2006C04-1
© 2006.03
Sony Corporation
Personal Audio Division
Published by Sony Techno Create Corporation
AEP Model
UK Model
2
Battery life
For CD radio cassette-corder:
FM recording
Sony R20P: approx. 13.5 h
Sony alkaline LR20: approx. 20 h
Tape playback
Sony R20P: approx. 7.5 h
Sony alkaline LR20: approx. 15 h
CD playback
Sony R20P: approx. 2.5 h
Sony alkaline LR20: approx. 7 h
Dimensions
Approx. 386
×
166
×
252 mm (w/h/d)
(incl. projecting parts)
Mass
Approx. 3.3 kg (incl. batteries)
Supplied accessories
Main lead (1)
Design and specifications are subject to change without
notice.
notice.
CFD-S100L
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK
0
OR DOTTED LINE
WITH MARK
0
ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE
PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR
IN SUPPLEMENTS PUBLISHED BY SONY.
REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE
PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR
IN SUPPLEMENTS PUBLISHED BY SONY.
CAUTION
Use of controls or adjustments or performance of proce-
dures other than those specified herein may result in haz-
ardous radiation exposure.
dures other than those specified herein may result in haz-
ardous radiation exposure.
Flexible Circuit Board Repairing
•
Keep the temperature of the soldering iron around 270˚C during
repairing.
repairing.
•
Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
circuit board (within 3 times).
•
Be careful not to apply force on the conductor when soldering
or unsoldering.
or unsoldering.
Notes on Chip Component Replacement
•
Never reuse a disconnected chip component.
•
Notice that the minus side of a tantalum capacitor may be dam-
aged by heat.
aged by heat.
NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK
OR BASE UNIT
OR BASE UNIT
The laser diode in the optical pick-up block may suffer electrostatic
breakdown because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic breakdown and also use
the procedure in the printed matter which is included in the repair
parts.
The flexible board is easily damaged and should be handled with
care.
breakdown because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic breakdown and also use
the procedure in the printed matter which is included in the repair
parts.
The flexible board is easily damaged and should be handled with
care.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused on
the disc reflective surface by the objective lens in the optical pick-
up block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.
the disc reflective surface by the objective lens in the optical pick-
up block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.
This Compact Disc player is
classified as a CLASS 1
LASER product.
The CLASS 1 LASER
PRODUCT mark is located
at the bottom.
classified as a CLASS 1
LASER product.
The CLASS 1 LASER
PRODUCT mark is located
at the bottom.
3
TABLE OF CONTENTS
1. SERVICING NOTES
......................................................... 4
2. GENERAL
............................................................................ 5
3. DISASSEMBLY
3-1. Cabinet Top Assy ................................................................ 7
3-2. Cabinet Front Assy, Cabinet Rear Assy .............................. 7
3-3. Wires ................................................................................... 8
3-4. MD Block ............................................................................ 8
3-5. Cassette Door Assy ............................................................. 9
3-6. LCD Board, Control (4) Board ........................................... 9
3-7. Main Board ....................................................................... 10
3-8. Tuner Board ....................................................................... 10
3-9. Power Board ...................................................................... 11
3-10. CD Lid ............................................................................... 11
3-11. CD Block Assy .................................................................. 12
3-12. Optical Pick-up ................................................................. 12
3-13. R/P Head (HRP301), TC Board ........................................ 13
3-14. Motor Assy (M801), Main Belt (B), Sub Belt (B) ............ 13
3-2. Cabinet Front Assy, Cabinet Rear Assy .............................. 7
3-3. Wires ................................................................................... 8
3-4. MD Block ............................................................................ 8
3-5. Cassette Door Assy ............................................................. 9
3-6. LCD Board, Control (4) Board ........................................... 9
3-7. Main Board ....................................................................... 10
3-8. Tuner Board ....................................................................... 10
3-9. Power Board ...................................................................... 11
3-10. CD Lid ............................................................................... 11
3-11. CD Block Assy .................................................................. 12
3-12. Optical Pick-up ................................................................. 12
3-13. R/P Head (HRP301), TC Board ........................................ 13
3-14. Motor Assy (M801), Main Belt (B), Sub Belt (B) ............ 13
4. MECHANICAL ADJUSTMENTS
............................... 14
5. ELECTRICAL ADJUSTMENTS
Tape Section .......................................................................... 14
Tuner Section ......................................................................... 15
CD Section ............................................................................ 16
Tuner Section ......................................................................... 15
CD Section ............................................................................ 16
6. DIAGRAMS
6-1. IC Pin Description ............................................................. 17
6-2. Circuit Boards Location .................................................... 17
6-3. Block Diagram – CD Section – ......................................... 18
6-4. Block Diagram – Main Section – ...................................... 19
6-5. Printed Wiring Board – CD Section – ............................... 20
6-6. Schematic Diagram – CD Section – .................................. 21
6-7. Printed Wiring Board – Tuner Section – ........................... 22
6-8. Schematic Diagram – Tuner Section – .............................. 23
6-9. Printed Wiring Boards – Main Section – .......................... 24
6-10. Schematic Diagram – Main Section (1/2) – ...................... 25
6-11. Schematic Diagram – Main Section (2/2) – ...................... 26
6-12. Printed Wiring Board – TC Section – ............................... 27
6-13. Schematic Diagram – TC Section – .................................. 28
6-14. Printed Wiring Boards – Control Section – ....................... 29
6-15. Schematic Diagram – Control Section – ........................... 30
6-16. Printed Wiring Boards – Display Section – ...................... 31
6-17. Schematic Diagram – Display Section – ........................... 32
6-18. Printed Wiring Boards – Power Supply Section – ............ 33
6-19. Schematic Diagram – Power Supply Section – ................. 34
6-20. IC Block Diagrams ............................................................ 35
6-2. Circuit Boards Location .................................................... 17
6-3. Block Diagram – CD Section – ......................................... 18
6-4. Block Diagram – Main Section – ...................................... 19
6-5. Printed Wiring Board – CD Section – ............................... 20
6-6. Schematic Diagram – CD Section – .................................. 21
6-7. Printed Wiring Board – Tuner Section – ........................... 22
6-8. Schematic Diagram – Tuner Section – .............................. 23
6-9. Printed Wiring Boards – Main Section – .......................... 24
6-10. Schematic Diagram – Main Section (1/2) – ...................... 25
6-11. Schematic Diagram – Main Section (2/2) – ...................... 26
6-12. Printed Wiring Board – TC Section – ............................... 27
6-13. Schematic Diagram – TC Section – .................................. 28
6-14. Printed Wiring Boards – Control Section – ....................... 29
6-15. Schematic Diagram – Control Section – ........................... 30
6-16. Printed Wiring Boards – Display Section – ...................... 31
6-17. Schematic Diagram – Display Section – ........................... 32
6-18. Printed Wiring Boards – Power Supply Section – ............ 33
6-19. Schematic Diagram – Power Supply Section – ................. 34
6-20. IC Block Diagrams ............................................................ 35
7. EXPLODED VIEWS
7-1. Main Section ..................................................................... 38
7-2. Cabinet Front Section ........................................................ 39
7-3. Cabinet Top Section .......................................................... 40
7-4. Cabinet Rear Section ......................................................... 41
7-5. Tape Mechanism Section .................................................. 42
7-6. CD Mechanism Section .................................................... 43
7-2. Cabinet Front Section ........................................................ 39
7-3. Cabinet Top Section .......................................................... 40
7-4. Cabinet Rear Section ......................................................... 41
7-5. Tape Mechanism Section .................................................. 42
7-6. CD Mechanism Section .................................................... 43
8. ELECTRICAL PARTS LIST
......................................... 44
CFD-S100L
4
CFD-S100L
CHUCK PLATE JIG ON REPAIRING
On repairing CD section, playing a disc without the lid (CD), use
Chuck Plate Jig.
• Code number of Chuck Plate Jig: X-4918-255-1
Chuck Plate Jig.
• Code number of Chuck Plate Jig: X-4918-255-1
SECTION 1
SERVICING NOTES
LASER DIODE AND FOCUS SEARCH OPERATION
CHECK
CHECK
1. Turn ON the [OPERATE] button and press [CD] button to CD
position.
2. Open the CD lid.
3. Turn on S801 with screwdriver, etc. as following figure.
4. Press the N X (CD) button.
5. Confirm the laser diode emission while observing the objecting
3. Turn on S801 with screwdriver, etc. as following figure.
4. Press the N X (CD) button.
5. Confirm the laser diode emission while observing the objecting
lens. When there is no emission, Auto Power Control circuit or
Optical Pick-up is broken.
Objective lens moves up and down three times for focus search.
Optical Pick-up is broken.
Objective lens moves up and down three times for focus search.
S801