Read Sony CDP-XE800 Service Manual online
— 2 —
SAFETY-RELATED COMPONENT WARNING !!
COMPONENTS IDENTIFIED BY MARK
!
OR DOTTED
LINE WITH MARK
!
ON THE SCHEMATIC DIAGRAMS
AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERA-
TION. REPLACE THESE COMPONENTS WITH SONY
PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN
THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY
SONY.
This appliance is classified as a
CLASS 1 LASER product.
The CLASS 1 LASER
PRODUCT MARKING is
located on the rear exterior.
CLASS 1 LASER product.
The CLASS 1 LASER
PRODUCT MARKING is
located on the rear exterior.
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous ra-
diation exposure.
other than those specified herein may result in hazardous ra-
diation exposure.
This caution
label is located
inside the unit.
label is located
inside the unit.
TABLE OF CONTENTS
Section
Title
Page
SECTION 1. SERVICING NOTE
...................................... 3
SECTION 2. GENERAL
................................................
4
SECTION 3. DISASSEMBLY
3-1.
Front Panel Assembly ......................................................... 5
SECTION 4. TEST MODE
..............................................
6
SECTION 5. ELECTRICAL BLOCK CHECKING
......
8
SECTION 6. DIAGRAMS
6-1.
Circuit Boards Location ................................................... 10
6-2.
IC Pin Function
• IC801 System Control,
• IC801 System Control,
Fluorescent Indicator Tube Drive (CXP82316-060Q) .. 11
6-3.
Printed Wiring Board — BD Section — .......................... 13
6-4.
Schematic Diagram — BD Section — ............................. 15
6-5.
Printed Wiring Board — Main Section — ....................... 20
6-6.
Schematic Diagram — Main Section — .......................... 23
SECTION 7. EXPLODED VIEWS
7-1.
Front Panel Section .......................................................... 27
7-2.
Chassis Section ................................................................. 28
7-3.
CD Mechanism Section (CDM36-14) .............................. 29
7-4.
Base Unit Section (BU-14) ............................................... 30
SECTION 8. ELECTRICAL PARTS LIST
.................
31
ADVARSEL
: USYNLIG LASERSTRÅLING VED ÅBNING NÅR
SIKKERHEDSAFBRYDERE ER UDE AF FUNKTION. UNDGÅ UDSAETTELSE
FOR STRÅLING.
FOR STRÅLING.
CAUTION
: INVISIBLE LASER RADIATION WHEN OPEN AND
INTERLOCKS DEFEATED. AVOID EXPOSURE TO BEAM.
VARO!
: AVATTAESSA JA SUOJALUKITUS OHITETTAESSA OLET ALT-
TIINA NÄKYMÄTTÖMÄLLE LASERSÄTEILYLLE. ÄLÄ KATSO SÄTEESEEN.
VARNING
: OSYNLIG LASERSTRÅLING NÄR DENNA DEL ÄR ÖPP-
NAD OCH SPÄRREN ÄR URKOPPLAD. BETRAKTA EJ STRÅLEN.
VORSICHT
: UNSICHTBARE LASERSTRAHLUNG, WENN
ABDECKUNG GEÖFFNET UND SICHEREITSVERRIEGELUNG
ÜBERBRÜCKT. NICHT DEM STRAHL AUSSETZEN.
ÜBERBRÜCKT. NICHT DEM STRAHL AUSSETZEN.
ADVARSEL
: USYNLIG LASERSTRÅLING NÅR DEKSEL ÅPNES OG
SIKKERHEDSLÅS BRYTES. UNNGÅ EKSPONERING FOR STRÅLEN.
Notes on chip component replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be
• Notice that the minus side of a tantalum capacitor may be
damaged by heat.
Flexible Circuit Board Repairing
• Keep the temperature of soldering iron around 270˚C
during repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.
Click on the first or last page to see other CDP-XE800 service manuals if exist.