Read Sony CDP-XE700 Service Manual online
— 2 —
SAFETY-RELATED COMPONENT WARNING !!
COMPONENTS IDENTIFIED BY MARK
!
OR DOTTED
LINE WITH MARK
!
ON THE SCHEMATIC DIAGRAMS
AND IN THE PARTS LIST ARE CRITICAL TO SAFE
OPERATION. REPLACE THESE COMPONENTS WITH
SONY PARTS WHOSE PART NUMBERS APPEAR AS
SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.
This appliance is classified as
a CLASS 1 LASER product.
The CLASS 1 LASER
PRODUCT MARKING is
located on the rear exterior.
a CLASS 1 LASER product.
The CLASS 1 LASER
PRODUCT MARKING is
located on the rear exterior.
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous ra-
diation exposure.
other than those specified herein may result in hazardous ra-
diation exposure.
Notes on chip component replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be
• Notice that the minus side of a tantalum capacitor may be
damaged by heat.
Flexible Circuit Board Repairing
• Keep the temperature of soldering iron around 270˚C
during repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.
This caution
label is located
inside the unit.
label is located
inside the unit.
TABLE OF CONTENTS
Section
Title
Page
SECTION 1. SERVICING NOTE
...................................
3
SECTION 2. GENERAL
...................................................... 4
SECTION 3. DISASSEMBLY
3-1.
Front Panel Assembly ......................................................... 5
SECTION 4. TEST MODE
..............................................
6
SECTION 5. ELECTRICAL BLOCK CHECKING
......
8
SECTION 6. DIAGRAMS
6-1.
Circuit Boards Location ................................................... 10
6-2.
IC Pin Function
• IC801 System Control,
• IC801 System Control,
Fluorescent Indicator Tube Drive (CXP82316-069Q) .. 11
6-3.
Printed Wiring Board — BD Section — .......................... 13
6-4.
Schematic Diagram — BD Section — ............................. 15
6-5.
Printed Wiring Board — Main Section — ....................... 20
6-6.
Schematic Diagram — Main Section — .......................... 23
SECTION 7. EXPLODED VIEWS
7-1.
Front Panel Section .......................................................... 27
7-2.
Chassis Section ................................................................. 28
7-3.
CD Mechanism Section (CDM36-14) .............................. 29
7-4.
Base Unit Section (BU-14) ............................................... 30
SECTION 8. ELECTRICAL PARTS LIST
.................
31
ADVARSEL
: USYNLIG LASERSTRÅLING VED ÅBNING NÅR
SIKKERHEDSAFBRYDERE ER UDE AF FUNKTION. UNDGÅ UDSAETTELSE
FOR STRÅLING.
FOR STRÅLING.
CAUTION
: INVISIBLE LASER RADIATION WHEN OPEN AND
INTERLOCKS DEFEATED. AVOID EXPOSURE TO BEAM.
VARO!
: AVATTAESSA JA SUOJALUKITUS OHITETTAESSA OLET ALT-
TIINA NÄKYMÄTTÖMÄLLE LASERSÄTEILYLLE. ÄLÄ KATSO SÄTEESEEN.
VARNING
: OSYNLIG LASERSTRÅLING NÄR DENNA DEL ÄR ÖPP-
NAD OCH SPÄRREN ÄR URKOPPLAD. BETRAKTA EJ STRÅLEN.
VORSICHT
: UNSICHTBARE LASERSTRAHLUNG, WENN
ABDECKUNG GEÖFFNET UND SICHEREITSVERRIEGELUNG
ÜBERBRÜCKT. NICHT DEM STRAHL AUSSETZEN.
ÜBERBRÜCKT. NICHT DEM STRAHL AUSSETZEN.
ADVARSEL
: USYNLIG LASERSTRÅLING NÅR DEKSEL ÅPNES OG
SIKKERHEDSLÅS BRYTES. UNNGÅ EKSPONERING FOR STRÅLEN.
The laser component in this product
is capable of emitting radiation
exceeding the limit for Class 1.
is capable of emitting radiation
exceeding the limit for Class 1.
MODEL IDENTIFICATION
— BACK PANEL —
— BACK PANEL —
4-978-904-1
π: AEP, German model
4-979-904-8
π: UK model
Click on the first or last page to see other CDP-XE700 service manuals if exist.