Read Sony CDP-LSA1 Service Manual online
6
4
GB
Getting Started
Hooking Up the System
Overview
This section describes how to hook up the CD player to
a receiver or other components such as an MD deck.
Be sure to turn off the power to all components before
you start connecting them.
a receiver or other components such as an MD deck.
Be sure to turn off the power to all components before
you start connecting them.
i.LINK
S200
:
i.LINK
S200
b
*
You can connect components to either i.LINK S200
connector.
What cords will I need?
i.LINK connecting cable (supplied) (1)
Unpacking
Check that you have received the following items:
• i.LINK connecting cable (1)
• Remote commander (remote) (1)
• i.LINK connecting cable (1)
• Remote commander (remote) (1)
Before using the supplied remote
The supplied remote already contains a battery. Before
using the remote, pull out the insulating sheet to allow
the power to flow from the battery.
using the remote, pull out the insulating sheet to allow
the power to flow from the battery.
To avoid battery leakage
If you don’t use the remote for an extended period of time,
remove the battery to avoid possible damage from battery
leakage and corrosion.
leakage and corrosion.
z
When to replace the battery
Under normal conditions, the battery should last for
about six months. When the remote no longer operates
about six months. When the remote no longer operates
the player, replace the battery with a new one.
Notes on lithium battery
• Keep the lithium battery out of the reach of the children.
Should the battery be swallowed, immediately consult a
doctor.
• Wipe the battery with a dry cloth to assure a good contact.
• Be sure to observe the correct polarity when inserting the
battery.
• Do not hold the battery with metallic tweezers, otherwise a
short-circuit may occur.
WARNING
Battery may explode if mistreated.
Do not recharge, disassemble, or dispose of in fire.
CDP-LSA1
Receiver*
Signal flow
To a mains
Getting Started
MD deck, etc.*
l
;
;
Getting Started
5
GB
Getting Started
Hookups
Connecting the player to a receiver
Connect the receiver to the i.LINK S200 connector with
the i.LINK connecting cable (supplied). Make sure all
connections are firm. If not, there will be no sound
from the speakers.
Connect the receiver to the i.LINK S200 connector with
the i.LINK connecting cable (supplied). Make sure all
connections are firm. If not, there will be no sound
from the speakers.
v
v
v
v
:
i.LINK S200
i.LINK S200
Notes
• Do not connect the mains lead of any component until all
the connections have been completed.
• Do not allow any metal object to enter the i.LINK S200
connector as this may short-circuit the connector and
damage the components.
z
The other i.LINK S200 connector can be used to
connect other components
connect other components
The following i.LINK components can be used with the
player:
• STR-LSA1 receiver
• MDS-LSA1 MD deck
• MDS-LSA1 MD deck
Be sure to use the Sony i.LINK S200 connecting cable
(4 pins - 4 pins ).
z
For general information about i.LINK
See “About i.LINK” on page 16.
Connecting the mains lead
Connect the mains lead to a mains.
Removing the protective bar
Remove the attached protective bar and retain it for
use when transporting the player at a later time.
use when transporting the player at a later time.
DISP
LAY
When you connect the mains lead to a mains, the disc
tray will close automatically after a while.
tray will close automatically after a while.
Where do I go next?
Now you’re ready to use your player.
If you aren’t familiar with how to play CDs, go to the section
“Playing a CD” on page 6.
Then, go to the following sections for other operations.
If you aren’t familiar with how to play CDs, go to the section
“Playing a CD” on page 6.
Then, go to the following sections for other operations.
Receiver
CDP-LSA1
Signal flow
Attaching the protective bar
When transporting the player, be sure to attach the
protective bar (which you removed at the time you
unpacked the player) onto the disc tray, and use
adhesive tape to secure the bar. If you fail to
attach the protective bar, the player may be
damaged during transport.
protective bar (which you removed at the time you
unpacked the player) onto the disc tray, and use
adhesive tape to secure the bar. If you fail to
attach the protective bar, the player may be
damaged during transport.
1
With the disc tray opened, disconnect the
mains lead.
mains lead.
2
Place the protective bar on the disc tray as
shown below.
shown below.
DISP
LAY
3
Push the disc tray with your fingers to close it.
DISP
LAY
Slowly push both sides of the disc tray as
shown above.
4
Secure the protective bar with adhesive tape.
DISP
LAY
l
;
A
A
A
Click on the first or last page to see other CDP-LSA1 service manuals if exist.