Read Sony CDP-CE575 Service Manual online
34
CDP-CE575
•
MAIN BOARD IC301 CXP84648-085Q (SYSTEM CONTROLLER)
Pin No.
Pin Name
I/O
Description
1 to 4
A3 to A6
O
Address signal output to the static RAM (IC302)
5
GND
—
Ground terminal
6 to 13
D0 to D7
I/O
Two-way data bus with the static RAM (IC302)
14
CE
O
Chip select signal output to the static RAM (IC302)
15 to 18
NC
—
Not used (open)
19
WE
O
Write enable signal output to the static RAM (IC302)
20
LOAD OUT
O
Loading motor (M10) drive signal output to the BA6780 (IC11)
21
LOAD IN
O
Loading motor (M10) drive signal output to the BA6780 (IC11)
22
FL CLK
O
Serial data transfer clock signal output to the FL driver (IC801)
23
FL DATA
O
Serial data output to the FL driver (IC801)
24
FL RST
O
Reset signal output to the FL driver (IC801)
25 to 27
A13, A14, A7
O
Address signal output to the static RAM (IC302)
28
DSENS
I
Detect signal input from the disc sensor (D11)
29
NC
—
Not used (open)
30
RST
I
System reset signal input from the reset signal generator (IC603) “L”: reset
For several hundreds msec. after the power supply rises, “L” is input, then it changes to “H”
For several hundreds msec. after the power supply rises, “L” is input, then it changes to “H”
31
EXTAL
I
Main system clock input terminal (10 MHz)
32
XTAL
O
Main system clock output terminal (10 MHz)
33
VSS
—
Ground terminal
34
TX
O
Sub system clock output terminal Not used (open)
35
TEX
I
Sub system clock input terminal Not used (fixed at “L”)
36
AVSS
—
Ground terminal (for A/D converter)
37
AVREF
I
Reference voltage input terminal (+5V)
38
NC
—
Not used (open)
39
VERSION
I
Model Destination setting terminal
40
ADJ
I
Setting terminal for the test mode
41
KEY4
I
Key input terminal (A/D input) (S941 to S845) FADER, PEAK SEARCH, CLEAR, CHECK,
EDIT keys input
EDIT keys input
42
KEY3
I
Key input terminal (A/D input) (S831 to S838) DISC 5, DISC 4, DISC 3, DISC 2, DISC 1,
CONTINUE, SHUFFLE, PROGRAM keys input
CONTINUE, SHUFFLE, PROGRAM keys input
43
KEY2
I
Key input terminal (A/D input) (S821 to S827) MEGA CONTROL, X-FADER NO DELAY,
MENU, m (AMS–), M (AMS+), TIME/TEXT, REPEAT keys input
MENU, m (AMS–), M (AMS+), TIME/TEXT, REPEAT keys input
44
KEY1
I
Rotary encoder key input terminal (A/D input) (S801, S811 to S815) l AMS L (DISC)
PUSH ENTER, H, X, s, EX-CHANGE, DISC SKIP keys input
PUSH ENTER, H, X, s, EX-CHANGE, DISC SKIP keys input
45
NC
—
Not used (open)
46
TSENS
I
Detect signal input from the table sensor (D10)
47
FLT
O
Serial data latch pulse output to the FL driver (IC801)
48
CLK
O
Serial data transfer clock signal output to the CXD2587Q (IC101)
49
NC
O
Not used (open)
50
DATA
O
Serial data output to the CXD2587Q (IC101)
51
SQCK
O
Sub-code Q data reading clock signal output to the CXD2587Q (IC101)
52
SQSO
I
Sub-code Q data signal input from the CXD2587Q (IC101)
53
NC
—
Not used (open)
54
SENSE
I
Internal status (SENSE) signal input from the CXD2587Q (IC101)
55
NC
I
Not used (fixed at “H”)
56
RMIN
I
Remote control signal input from the remote control receiver (IC802)
Click on the first or last page to see other CDP-CE575 service manuals if exist.