Read Sony BMZ-K1 / CX-BK1 Service Manual online
25
CX-BK1
SECTION 6
MECHANICAL ADJUSTMENTS
•
TAPE MECHANISM DECK SECTION
Note:
Tape deck is not loaded in US model.
Precaution
1. Clean the following parts with a denatured alcohol-moistened
swab:
record/playback heads
pinch rollers
erase head
rubber belts
capstan
idlers
2. Demagnetize the record/playback head with a head
demagnetizer.
3. Do not use a magnetized screwdriver for the adjustments.
4. After the adjustments, apply suitable locking compound to the
4. After the adjustments, apply suitable locking compound to the
parts adjusted.
5. The adjustments should be performed with the rated power
supply voltage unless otherwise noted.
Torque Measurement
2.94 – 7.84 mN • m
(30 to 79 g • cm)
(0.42 – 1.11 oz • inch)
0.15 – 0.6 mN • m
2 to 6 g • cm
(0.03 – 0.08 oz • inch)
2.94 – 7.84 mN • m
(30 to 79 g • cm)
(0.42 – 1.11 oz • inch)
2.94 – 7.84 mN • m
(30 to 79 g • cm)
(0.42 – 1.11 oz • inch)
6.86 – 17.64 mN • m
(70 to 179 g • cm)
(0.98 – 2.49 oz • inch)
9.8 mN • m
(100 • cm or more)
(1.4 oz • inch or more)
9.8 mN • m
(100 • cm or more)
(1.4 oz • inch or more)
Mode
Torque meter
CQ-102C
CQ-102C
CQ-102RC
CQ-102RC
CQ-201B
CQ-403A
CQ-403R
Meter reading
FWD
FWD
back tension
back tension
REV
REV
back tension
back tension
FF/REV
FWD tension
REV tension
SECTION 7
ELECTRICAL ADJUSTMENTS
Note:
Tape deck is not loaded in US model.
Precaution
1. Demagnetize the record/playback head with a head
demagnetizer.
2. Do not use a magnetized screwdriver for the adjustments.
3. After the adjustments, apply suitable locking compound to the
3. After the adjustments, apply suitable locking compound to the
parts adjust.
4. The adjustments should be performed with the rated power
supply voltage unless otherwise noted.
5. The adjustments should be performed in the order given in
this service manual. (As a general rule, playback circuit ad-
justment should be completed before performing recording
circuit adjustment.)
justment should be completed before performing recording
circuit adjustment.)
6. The adjustments should be performed for both L-CH and R-
CH.
7. Switches and controls should be set as follows unless other-
wise specified.
• Test Tape
Tape
Signal
Used for
P-4-A100
10 kHz, – 10 dB
Azimuth Adjustment
WS-48B
3 kHz, 0 dB
Tape Speed Check
0 dB = 0.775 V
DECK SECTION
2. Turn the adjustment screw and check output peaks. If the peaks
do not match for L-CH and R-CH, turn the adjustment screw
so that outputs match within 1dB of peak.
so that outputs match within 1dB of peak.
Screw
position
position
L-CH
peak
peak
within
1dB
1dB
Output
level
level
L-CH
peak
peak
R-CH
peak
peak
within
1dB
1dB
Screw
position
position
R-CH
peak
peak
Record/Playback Head Azimuth Adjustment
Procedure:
1. Mode: Playback
1. Mode: Playback
set
SPEAKER board
SPEAKER terminal (JK502)
L-CH, R-CH
SPEAKER terminal (JK502)
L-CH, R-CH
+
–
–
level meter
test tape
P-4-A100
(10 kHz, – 10 dB)
P-4-A100
(10 kHz, – 10 dB)
Click on the first or last page to see other BMZ-K1 / CX-BK1 service manuals if exist.