BDV-IS1000, BDV-IT1000, BDV-IT1000ES, HCD-IS1000, HCD-IT1000 - Sony Audio Service Manual (repair manual). Page 4

The laser diode in the optical pick-up block may suffer electrostat-
ic break-down because of the potential difference generated by the 
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic break-down and also 
use the procedure in the printed matter which is included in the 
repair parts.
The fl exible board is easily damaged and should be handled with 
care.

NOTES  ON  LASER  DIODE  EMISSION  CHECK
The laser beam on this model is concentrated so as to be focused 
on the disc refl ective surface by the objective lens in the optical 
pickup block. Therefore, when checking the laser diode emission, 
observe from more than 30 cm away from the objective lens.

UNLEADED  SOLDER
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution:  Some printed circuit boards may not come printed with 

the lead free mark due to their particular size)

Unleaded solder has the following characteristics.
•  Unleaded solder melts at a temperature about 40 °C higher 

than ordinary solder.

 

Ordinary soldering irons can be used but the iron tip has to be 
applied to the solder joint for a slightly longer time.

 

Soldering irons using a temperature regulator should be set to 
about 350 °C.
Caution: The printed pattern (copper foil) may peel away if 

the heated tip is applied for too long, so be careful!

• Strong 

viscosity

 

Unleaded solder is more viscous (sticky, less prone to fl ow) 
than ordinary solder so use caution not to let solder bridges 
occur such as on IC pins, etc.

•  Usable with ordinary solder
 

It is best to use only unleaded solder but unleaded solder may 
also be added to ordinary solder.

RELEASING  THE  DISC  TRAY  LOCK
The disc tray lock function for the antitheft of an demonstration 
disc in the store is equipped.

Releasing Procedure:
1.  Press the [

?/1

] button to turn on the system.

2.  Touch the [FUNCTION] sensor to select “DVD”.
3.  Touch the [

x

] and [

Z

] sensors simultaneously and hold down 

unit “UNLOCKED” displayed on the fluorescent indicator 
tude (around 5 seconds).

Note: When “LOCKED” is displayed, the disc slot lock is not released by 

turning power on/off with the [?/1] button.

NOTE  WHEN  PARTS  THAT  CANNOT  BE  SUPPLIED  
ARE  REPLACED
There are parts that cannot be exchanged with single parts in this 
set. The following parts are damaged, exchange the entire mounted 
board.
DSP board 

: IC5021

HD board 

: IC504, IC708, IC710

MB-126 board 

: IC101, IC104, IC105, IC204, IC205, IC307, 

IC308, IC501, IC601, IC602, IC700, IC701, 
IC8001, L8001, L8002, X401

T-SENSOR board  : IC121

J-6090-199-A

BLX-104

Single Layer

J-6090-200-A

BLX-204

Dual Layer

3-702-101-01

CD (YEDS-18)

J-6090-088-A

HLX-504

Single Layer (NTSC)

J-6090-089-A

HLX-505

Dual Layer (NTSC)

J-6090-077-A

HLX-506

Single Layer (PAL)

J-6090-078-A

HLX-507

Dual Layer (PAL)

Note: Refer to the service manual of BDP-BX1/S350 (Part No. 9-883-

989-1[]) (page 1-3 to 1-14E) for the use of BLX-104/204.

1. BLX-104
Procedure:
1. Select 

23.976Hz/1080p.

2. Play 

“4.Motion 

pictures”.

3.  Check whether palyer can play back or not.
4.  Check each outputs.
 Video:
 Composite/S 

Video/component/HDMI.

 Audio:
 Speaker 

out.

*  When 1080/24p monitor is nothing, 1080i (59.94Hz or 50Hz) 

can use instead of 1080/24p.

 

However this is temporary correspondence.

*  When the output of HDMI is 1080p, the signal of Composite/S 

Video/Component are not output.

 

It is necessary to lower the output of HDMI to 1080i or less.

2. BLX-204
Procedure:
1.  Select 1080i (59.94Hz or 50Hz).
2. Play 

“4.Motion 

pictures”.

3.  Check whether player can play back or not.
 

(Check the picture and sound output)

3. CD (YEDS-18)
Procedure:
Check whether player can play back or not.
(Check the sound output)

4.  HLX-504/505 (NTSC), HLX-506/507 (PAL)
Procedure:
1.  After displayed Main Menu, select “1.Video”.
2.  Play “1.Color bar 100%”.
 

(Check the picture and sound output)

3.  Return to Menu.
4.  Play “Demonstration 4:3” or “5.Demonstration 16:9”.
 

(Check the picture and sound output)