Read Sony BDV-IS1000 / BDV-IT1000 / BDV-IT1000ES / HCD-IS1000 / HCD-IT1000 Service Manual online
HCD-IS1000/IT1000/IT1000ES
2
NOTES ON CHIP COMPONENT REPLACEMENT
•
•
Never reuse a disconnected chip component.
•
Notice that the minus side of a tantalum capacitor may be dam-
aged by heat.
aged by heat.
FLEXIBLE CIRCUIT BOARD REPAIRING
•
•
Keep the temperature of soldering iron around 270 °C during
repairing.
repairing.
•
Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
circuit board (within 3 times).
•
Be careful not to apply force on the conductor when soldering
or unsoldering.
or unsoldering.
SAFETY CHECK-OUT
After correcting the original service problem, perform the follow-
ing safety check before releasing the set to the customer:
Check the antenna terminals, metal trim, “metallized” knobs,
screws, and all other exposed metal parts for AC leakage.
Check leakage as described below.
After correcting the original service problem, perform the follow-
ing safety check before releasing the set to the customer:
Check the antenna terminals, metal trim, “metallized” knobs,
screws, and all other exposed metal parts for AC leakage.
Check leakage as described below.
LEAKAGE TEST
The AC leakage from any exposed metal part to earth ground and
from all exposed metal parts to any exposed metal part having a
return to chassis, must not exceed 0.5 mA (500 microamperes.).
Leakage current can be measured by any one of three methods.
1. A commercial leakage tester, such as the Simpson 229 or RCA
The AC leakage from any exposed metal part to earth ground and
from all exposed metal parts to any exposed metal part having a
return to chassis, must not exceed 0.5 mA (500 microamperes.).
Leakage current can be measured by any one of three methods.
1. A commercial leakage tester, such as the Simpson 229 or RCA
WT-540A. Follow the manufacturers’ instructions to use these
instruments.
instruments.
2. A battery-operated AC milliammeter. The Data Precision 245
digital multimeter is suitable for this job.
3. Measuring the voltage drop across a resistor by means of a
VOM or battery-operated AC voltmeter. The “limit” indication
is 0.75 V, so analog meters must have an accurate low-voltage
scale. The Simpson 250 and Sanwa SH-63Trd are examples
of a passive VOM that is suitable. Nearly all battery operated
digital multimeters that have a 2 V AC range are suitable. (See
Fig. A)
is 0.75 V, so analog meters must have an accurate low-voltage
scale. The Simpson 250 and Sanwa SH-63Trd are examples
of a passive VOM that is suitable. Nearly all battery operated
digital multimeters that have a 2 V AC range are suitable. (See
Fig. A)
1.5 k
Ω
0.15
μF
AC
voltmeter
(0.75 V)
voltmeter
(0.75 V)
To Exposed Metal
Parts on Set
Parts on Set
Earth Ground
Fig. A. Using an AC voltmeter to check AC leakage.
CAUTION
Use of controls or adjustments or performance of procedures
other than those specifi ed herein may result in hazardous radia-
tion exposure.
Use of controls or adjustments or performance of procedures
other than those specifi ed herein may result in hazardous radia-
tion exposure.
Ver. 1.1
General
Power requirements
120 V AC, 60 Hz
(US, Canadian models)
(Except US, Canadian
models)
models)
Power consumption
On: 140 W
(HCD-IT1000/
Power Saving mode)
Power consumption
On: 100 W
(HCD-IS1000)
Standby: 0.3 W (at the
Power Saving mode)
Power Saving mode)
Output voltage/current
(DIGITAL MEDIA PORT)
(DIGITAL MEDIA PORT)
DC 5 V/700 mA
LAN (100):
100BASE-TX Terminal
EXTERNAL:
External memory slot (For
connecting the external
memory)
DC output: 5 V 500 mA
Max
connecting the external
memory)
DC output: 5 V 500 mA
Max
Dimensions (approx.)
430 mm × 125 mm × 355
mm (17 in × 5 in × 14 in)
(w/h/d) incl. projecting
parts
430 mm × 125 mm × 385
mm (17 in × 5 in × 15
mm (17 in × 5 in × 14 in)
(w/h/d) incl. projecting
parts
430 mm × 125 mm × 385
mm (17 in × 5 in × 15
1
/
4
in) (w/h/d) with the
wireless transceiver
inserted
wireless transceiver
inserted
Mass (approx.)
10 kg (22 lbs 1 oz)
Design and specifications are subject to change
without notice.
without notice.
Power requirements
220 - 240 V AC, 50/60 Hz
IT1000ES)
Standby: 0.3 W (at the
Tuner Section
(HCD-IS1000: Saudi Arabia, Singapore/
HCD-IT1000: Australian, Saudi Arabia and
Singapore models)
(HCD-IS1000: Saudi Arabia, Singapore/
HCD-IT1000: Australian, Saudi Arabia and
Singapore models)
System
PLL quartz-locked digital
synthesizer
synthesizer
FM tuner section
Tuning range
Tuning range
87.5 MHz - 108.0 MHz
(50 kHz step)
(50 kHz step)
Antenna (aerial)
FM wire antenna (aerial)
Antenna (aerial) terminals 75 ohms, unbalanced
Intermediate frequency
Intermediate frequency
10.7 MHz
AM tuner section
Tuning range
Australian models:
Tuning range
Australian models:
531 kHz - 1,710 kHz (with
the interval set at 9 kHz)
530 kHz - 1,710 kHz (with
the interval set at 10 kHz)
the interval set at 9 kHz)
530 kHz - 1,710 kHz (with
the interval set at 10 kHz)
Middle Eastern models:
531 kHz - 1,602 kHz (with
the interval set at 9 kHz)
the interval set at 9 kHz)
Other models:
531 kHz - 1,602 kHz (with
the interval set at 9 kHz)
530 kHz - 1,610 kHz (with
the interval set at 10 kHz)
the interval set at 9 kHz)
530 kHz - 1,610 kHz (with
the interval set at 10 kHz)
Antenna (aerial)
AM loop antenna (aerial)
Intermediate frequency
450 kHz
This appliance is
classified as a CLASS 1
LASER product. This
marking is located on the
rear exterior.
classified as a CLASS 1
LASER product. This
marking is located on the
rear exterior.
Self-diagnosis Function
When the self-diagnosis function is activated to
prevent the system from malfunctioning, an
error code appears in the front panel display, or
just
prevent the system from malfunctioning, an
error code appears in the front panel display, or
just
appears without any messages on the
entire screen. In these cases, check the
following.
following.
When an error code appears in
the front panel display
the front panel display
When just
appears without
any messages on the entire
screen
screen
Contact your nearest Sony dealer or local
authorized Sony service facility.
authorized Sony service facility.
Error code
Corrective action
Exxxx
Contact your nearest Sony dealer or
local authorized Sony service
facility and give the error code.
local authorized Sony service
facility and give the error code.
SYSTEM
ERROR
ERROR
Turn off the system, then turn it on.
If the system does not work
normally, consult your nearest Sony
dealer or local authorized Sony
service facility.
If the system does not work
normally, consult your nearest Sony
dealer or local authorized Sony
service facility.
SELF DIAGNOSIS FUNCTION
Click on the first or last page to see other BDV-IS1000 / BDV-IT1000 / BDV-IT1000ES / HCD-IS1000 / HCD-IT1000 service manuals if exist.