BDV-E500W, HCD-E500W - Sony Audio Service Manual (repair manual). Page 21

HCD-E500W

Procedure:
1.  Turn on the set.
2.  Input the following signal from Signal Generator to FM antenna 

input directly.

Carrier frequency : A = 87.5 MHz, B = 98 MHz, C = 108 MHz
Deviation 

: 75 kHz

Modulation 

: 1 kHz

ANT input 

: 35 dBu (EMF)

Note: Use 75 ohm coaxial cable to connect signal generator and the set. 

You cannot use video cable for checking.

 

Use signal generator whose output impedance is 75 ohm.

3.  Set to FM tuner function and tune A, B and C signals.
4. Confi rm “TUNED” is lit on the display for A, B and C signals.

When the selected station signal is received in good condi-

tion, “TUNED” is displayed.

J-6090-199-A

BLX-104

Single Layer

J-6090-200-A

BLX-204

Dual Layer

3-702-101-01

CD (YEDS-18)

J-6090-088-A

HLX-504

Single Layer (NTSC)

J-6090-089-A

HLX-505

Dual Layer (NTSC)

J-6090-077-A

HLX-506

Single Layer (PAL)

J-6090-078-A

HLX-507

Dual Layer (PAL)

Note: Refer to the service manual of BDP-BX1/S350 (Part No. 9-883-

989-1[]) (page 1-3 to 1-14E) for the use of BLX-104/204.

1. BLX-104
Procedure:
1. Select 

23.976Hz/1080p.

2.  Play “4.Motion picture”.
3.  Check whether player can play back or not.
4.  Check each outputs.
 Video:
 Composite/S 

Video/component/HDMI.

 Audio:
 Speaker 

out.

*  When 1080/24p monitor is nothing, 1080i (59.94Hz or 50Hz) 

can use instead of 1080/24p.

 

However this is temporary correspondence.

*  When the output of HDMI is 1080p, the signal of Composite/S 

Video/Component are not output.

 

It is necessary to lower the output of HDMI to 1080i or less.

2. BLX-204
Procedure:
1.  Select 1080i (59.94Hz or 50Hz).
2.  Play “4.Motion picture”.
3.  Check whether player can play back or not.
 

(Check the picture and sound output)

3. CD (YEDS-18)
Procedure:
Check whether player can play back or not.
(Check the sound output)

4.  HLX-504/505 (NTSC), HLX-506/507 (PAL)
Procedure:
1.  After displayed Main Menu, select “1.Video Signal”.
2.  Play “1.Color bar 100%”.
 

(Check the picture and sound output)

3.  Return to Menu.
4.  Play “Demonstration 4:3” or “Demonstration 16:9”.
 

(Check the picture and sound output)

4-1-2.  Playback operation confi rmation
Confi rm operation in each signal/output mode of test disc (BLX-
104/204) according to the content of the repair.

Note: “AV Sync.” doesn’t operate.

4-2. Networking Confi rmation
Confi rm it according to the following procedure when you confi rm 
the connection of the network.

Note: Do not execute “Network Diagnostic” of “Set up” of the home 

menu with only the router connected.

Procedure:
1.  Connect the router with the set with LAN cable.
2.  Turn on the power of the set and the router.
3.  Press the [HOME] button on the remote commander, and the 

home menu is displayed.

4.  Select “Set up” 

→ “Network Settings” → “Internet Settings”, 

and press the [3] button on the remote commander.

5. Confi rm “Use DHCP” is displayed in “IP Address Acquisi-

tion”, and confi rm IP address are displayed in “IP Address”, 
“Subnet Mask” and “Default Gateway”.

Internet Settings

IP Address Acquisition

Use DHCP

IP Address

XXX.XXX.XXX.XXX

DNS Server Acquisition

Auto Acquisition

DNS Server (Primary)

XXX.XXX.XXX.XXX

Subnet Mask

XXX.XXX.XXX.XXX

Default Gateway

XXX.XXX.XXX.XXX