AWP-ZP5, CX-LZP5 - Sony Audio Service Manual (repair manual). Page 2

2

System

Compact disc and digital
audio system

Laser

Semiconductor laser
(

λ=780 nm)

Emission duration:
continuous

Frequency response

2 Hz – 20 kHz

FM stereo, FM/AM superheterodyne tuner

FM tuner section

Tuning range
US, CND model:

87.5 – 108.0 MHz
(100-kHz step)

Other models:

87.5 – 108.0 MHz
(50-kHz step)

Antenna

FM lead antenna

Antenna terminals

75 ohms unbalanced

Intermediate frequency 10.7 MHz

AM tuner section

Tuning range
US, CND model:

530 – 1,710 kHz
(with the tuning interval
set at 10 kHz)
531 – 1,710 kHz
(with the tuning interval
set at 9 kHz)

AEP, UK model:

531 – 1,602 kHz
(with the tuning interval
set at 9 kHz)

E51, MY, SP, TW model: 530 – 1,710 kHz

(with the tuning interval
set at 10 kHz)
531 – 1,602 kHz
(with the tuning interval
set at 9 kHz)

Antenna

AM loop antenna, external
antenna terminal

Intermediate frequency 450 kHz

Power requirements
US, CND model:

120 V AC, 60 Hz

AEP, UK model:

230 V AC, 50/60 Hz

TW model:

120 V AC, 50/60 Hz

E51, MY, SP model:

110 – 120, 220 – 240 V
AC, 50/60 Hz
Adjustable with voltage
selector

Power consumption
AEP, UK model:

40 W
0.3 W (in Power Saving
mode)

US, CND model:

40 W

E51, MY, SP, TW model: 45 W
Dimensions (w/h/d) incl. projecting parts and controls
Amplifier/Tuner/CD section:

Approx. 108 

× 224.8 ×

327.1 mm

Mass
Amplifier/Tuner/CD section

Approx. 4.4 kg

• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be

damaged by heat.

• Keep the temperature of soldering iron around 270°C during

repairing.

• Do not touch the soldering iron on the same conductor of the

circuit board (within 3 times).

• Be careful not to apply force on the conductor when soldering

or unsoldering.

Boards requiring use of unleaded solder are printed with the lead
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with

the lead free mark due to their particular size)

Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40 

°C higher than

ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to about
350 

°C.

Caution: The printed pattern (copper foil) may peel away if the

heated tip is applied for too long, so be careful!

• Strong viscosity

Unleaded solder is more viscou-s (sticky, less prone to flow) than
ordinary solder so use caution not to let solder bridges occur such
as on IC pins, etc.

• Usable with ordinary solder

It is best to use only unleaded solder but unleaded solder may also
be added to ordinary solder.

• Abbreviation

CND

: Canadian model

E51

: Chilean and Peruvian model

MY

: Malaysia model

SP

: Sinpapore model

TW

: Taiwan model

0

0

0